Video

If these calipers have a radial mount and the same parameters from the mount to the center of the caliper, adapter will definitely work for you

@@_demon1k_ I’m sorry about that I meant 6 pistons and I have the rotors that goes with them and break line

@@KamGlobaI If you're talking about the 6 piston hellcat calipers you only need the srt steering knuckles, otherwise you can't install them, there is no adapter for those calipers

🤣 When you know everything in this world, there's no hurry.

I have shown the rest of the repair parts in the following videos

I don’t sell ready-made adapters, I can only sell a 3d model for manufacturing in your city

I don’t sell ready-made adapters, I can only sell a 3d model for manufacturing in your city

@@_demon1k_how much for the 3d model?

@@345Jo The cost of the model is 50€=55$=75CA$

You don't need to remove the steering wheel to remove the dash, just push it toward you and down.

Thanks! I’m going to be doing this soon. Do you recommend removing all the duct work sections (driver, passenger, and the center section that’s screwed to the dash panel) out all together? Looks like you kept the drivers section in the car when you did yours.

@@brandonsmith5827 You must remove all sections of the air duct or you will not be able to remove the instrument panel without damaging the windshield heating duct.

@@brandonsmith5827 To remove the air ducts unscrew the screws at the racks, remove the clip in the center and be sure to remove the screw that is behind the dashboard, this screw is the most difficult to access

Is there just one screw back there and is that the one you show in your video?

No, completely different headlights

I bought it on eBay

@@_demon1k_ can you please provide the link? Thank you

@@ma93256 www.ebay.com/itm/324916320246

@@_demon1k_ thank you! 🙏🏼

@@ma93256 you are welcome

Yeah, it's not everyone's favorite, but that's not me, my car has a stock exhaust.

Compare it to a Ford, Chevy or anyone's top trim V8 cars.. Its just louder on a cold start.

I don't get it either.

@@relguiatmont7336 I agree with you 100%

Nice joke 🤣

@@_demon1k_ not a joke.. i see you, have never been in a monster... look up competition car or home stereos.. SPL is everything you're missing.. 150db literally just get you in the club.. & no you dont need to be rich just good with numbers..

czcams.com/video/j8555LP-oaQ/video.htmlsi=3X6iqsNhOnkPrX1V

czcams.com/video/j8555LP-oaQ/video.htmlsi=3X6iqsNhOnkPrX1V

@@Thatrandomwhiteguy Would love to watch and listen to your competition car. A stereo system is a whole other topic of conversation

No, no, no, no, I try not to do that😅

You have to rev the motor for a very long time for the battery problem to show up. No problem with the fuses

@@_demon1k_ So you’ve changed the spark plugs?

@@ChryslerLeBaro No, I haven't, but I still have low mileage so I was surprised to see such a malfunction

No, full tank

Yeah, you're right.

No

It does, it takes a lot of time and wipes to clean off the glue between the touchscreen and the screen

I'm not sure it would be easier that way, it would require removing more parts to get to the side markers

If you have 4 piston brembo calipers, you don't need adapters because you have SRT knuckles. Just buy 6-piston calipers and hellcat brake disks.

Aluminum is also metal and can be straightened, but only small bends, I was just practicing on this hood, but such damage should not be repaired

Thank you so much😍

Thanks

I can sell you a 3D model of the adapter and you make it in your city on any milling or CNC machine. You will need Brembo GT calipers 6 or 8 piston calipers for 380-410mm/34mm brake disk (for today it is the newest model) or any available in your country Brembo calipers with radial mount for such disk, for example from Audi, Porsche, Mercedes or Bmw.

@@_demon1k_ what do you want for this? The idea with Porsche calipers Sounds wonderful, i only have to Look what Modell These calipers use (have no idea of Porsche 😌) are the screw holes of all brembo caliper are the same ?

@@dominikgsell469 For example, calipers like the ones in the photo forums.quattroworld.com/rs4b7/msgs/98644.phtml It is important that they can be installed on large brake disks, because the disk from the hellcat is 390/34mm. It is important that the mounting holes are 200mm and the distance from the holes to the caliper axle is 55mm I used this caliper, its price in Europe is 450 euros a piece www.brembo.com/en/car/sporting-use/gt-braking-systems

@@dominikgsell469 For 3D model cost, write me on instagram or better yet email me at slepushkin.oleg@gmail.com I will need to understand in what format you will need the model or drawings

@@_demon1k_ ok i will thx :-)

I need to understand what kind of steering knuckle is used on your car, if the same as on a rear wheel drive Challenger or Charger then my adapter will work for you and I can sell you a 3d model or drawings for fabrication. If you are using a different knuckle then you will need to design a different adapter, but I don't have data on the Durango range of knuckles at this time.

I have a charger 6 Piston front caliper for my Dodge Durango RT V8 2015 5.7 and my knuckle number is PSA46700. I want to adapt that brembo calipers to my Durango you think that is possible. Thank you for your help.

@@JulioHernandez-zx1sv There is not much place to mount the hellcat caliper to the steering knuckle via an adapter, as the hellcat caliper is laterally mounted to the steering knuckle . So I used a caliper with a radial mount so that an adapter of sufficient strength could be made. In your case, it would be easiest to mount the caliper without an adapter to the steering knuckle and use a two-piece brake disc like on a Charger or Challenger Hellcat, but fabricate a new center section to fit the required caliper outreach. I think that would be the easiest way to install these calipers.

Thank you for such an appreciation of my work

Thanks

I’m doing my Charger rt.

I can sell 3D model or blueprints to make the adapter. The adapter can be made on any CNC or milling machine in your city. I used new generation Brembo GT series calipers with radial mounts. You can buy them from a Brembo dealer: www.brembo.com/en/car/sporting-use/gt-braking-systems

Yes, on all v8 you can add the performance brake package as an option and then you have brakes like a hellcat

No, only on car monitors of 2016 year of release from the manufacturer panasonic, before 2016 were put magnetos from the manufacturer Harman and they do not have this problem, there screens are originally from two parts - the screen and touchscreen

68258750AC

Thanks

What are they? I have a 2006 dodge magnum srt8 and just got 2016 hellcat 6 piston calipers and 2 piece rotors. Could I use this product? It looks just like yours.

@@jeremymcclain891 If you have the magnum version of the srt8, you don't need additional adapters, you already have the srt front steering knuckles that the 6 piston calipers from hellcat mount to

I can provide a 3d model or drawings to make the adapter. To buy a model write to me in instagram or email

@_demon1k_ how do I get them?

No, hellcat calipers can be installed on RT only with SRT knuckles, because hellcat calipers are side mount (end mount). The adapter is designed to fit Brembo radial mount calipers without replacing the knuckles on RT, SXT, GT models

Yes, I plan to develop an adapter for jeep but right now I don't have a steering knuckle to scan the dimensions

Let me know if you need parts to scan. I have a 2006 dodge magnum srt8 and would love to use your adapters. We can work something out. I could send you parts to scan. You should come to America, and get out of there til things get better.

@@jeremymcclain891 Thanks! This adapter is designed for cars that don't have srt steering knuckles so you can install big brakes like on a hellcat. On models that use the srt steering knuckles, the brakes from the Hellcat can be installed without modification.

Hemi

wrote a reply on instagram

This was to gain experience working with aluminum. Later I did as you say)

Thanks

write me a message on Instagram (instagram.com/_demon1k_/) or email (slepushkin.oleg@gmail.com)

@@_demon1k_did you make a new ig account?

front fascia - 68258730AB air dam - 68258745AB

To separate the touchscreen from the screen, I used a string to separate the screens.

No, SRT steering knuckles are only needed to use the hellcat calipers. But they are heavier than the new generation of Brembo calipers and installing a set of hellcat brakes is more expensive. Here's a video of the full installation: czcams.com/video/pvNdbHZm2WI/video.htmlsi=kmxQ6S6uVYJea1QZ