Video

Thank you for the advice, Everything works be alive and well!

After reading everyone's comments. The fix is easy. The black sensor is the switch, the LED emitter must have failed (yellow LED). 2 wires going to the black pickup sensor switch from the black sensor, red and blue. The red is power, but that red also feeds two other reed switches, so don't cut that wire. The blue wire is the control wire for the sensor to the motherboard. All you have to do is cut the blue wire and splice it onto the power red wire. What I did was strip some insulation off the red wire, cut the blue wire, then wrap the blue wire to the red. Add some electrical tape, and done.

Use a high wattage aquarium heater jnstead, much safer. I have one in my Amazon basket waiting as we speak

you are just nit picking !

Many thanks for posting this video playboy

I had that truck Modifier. No exaggeration there. I loved that thing.

Great vid, thanks. Do you experience any corrosion with it being in chlorinated water?

I am going for a DIY hot tub, how long do you think it would take with just the immersion heater? and since you unplug when getting into the hot tub, how long do you think it would stay warm? i know you dont have the exact answer but what about a ballpark?

Does this not do the same thing as holding down the select button for 10 seconds or so?

If you soap the bead at the before roll up the stick, it would be much easier

Thanks for posting this video. My model has red and black cables on the left side and blue and white cables on the right side. Both are connected to the same plate clip. I cut everything 10 cm before the clip and wired all red and white cable and all black and blue cable and got the same result. Regards

Your info saved my igloo ice maker, thank you for the video! Woohoo

Dude this worked bro. I definitely appreciate it!!

Easy Peasy... Works like a charm... I'm glad I had the same model... No guessing witch wire was what... 5 minutes and I'm making ice...

How big of a solar generator would you need to run this cost free

1500 degrees? I don’t think so. 1500watts maybe.

es muy comun que marque add wather y lo mas probable es que tenga falso contacto en el panel donde se conecta ka bombita de agua

Thank you very much for your video! It's solved my problem instantly! Much appreciated!

Cant you just add hot water from the kitchen??

Thanks!!

i swear i got 2 degrees per hour in the winter. but then i've got the 85 or 90 inch tub- 4-5 person max. def will try an immersion heater

Did you get the green board at your Lowes store, or did you special order it? They don't have it at my local store and can't find it in their phones.

Mine's working OK now. Only one wire Blue/Black needed to be joined up. The other (Red) was power and was the same on both sides. No harm to cut/join the red wire, just not needed.

I think you just have to connect the two blue wires together and you can leave the red alone.

Do you leave the spa running 24/7? I have mine getting delivered in 24 hours.

Thanks for showing how to unclip the bulb from the wire. All other youtubes showed the grey connector where you pinch the two ears. You showed what I have, a black connector with a single detente in the middle. I couldn't have figured it out since I could not see the connector and had to work by touch only. Thanks!

I’ve been hearing water in pots like a pioneer woman 😂

Don’t cut the red on the right side, it’s the power for the sensor to water fill tray

I put 2" sheet insulation down between my inflatable tub and the cement slab. I also have a second cover called and EnergySense cover, so my tub will heat about 4 ° an hour.

Do you know what to do if the control arm just keeps moving? It will move like it’s going to make ice and then immediately go back to the drain position and just back and forth and won’t stop 😭

Looks like way too much work, I'll pay someone .

I’m doing the same kinda thing with my car right now! Nice!

Both are excellent. I would never say no to either.

It's not degrees. It's actually Watts. I could be wrong unless you like really hot hot tubs.😅

This shit going back too Walmart

On different models, the circuit board is different. I have a Model ICEB26HN55. You just need to follow the different wires to see which goes where.

Be real careful using that technique of driving up on a 4 by 4.... Every now and then the wheel will flip up and slap your fender, potentially causing $hundreds of damage.

Thanks for the vid, from 🏴󠁧󠁢󠁳󠁣󠁴󠁿

ROFLMAO😂😂😂😂😂😂

I appreciated this review! Several cases on my list of possible buys, was nice to see each put in and out!

Cool..I can lose 5 720E to one 2…😂😂😂😂

Okay so what I learned from this is that it's worth my time to just go to Discount Tire and ask them to pop my tires off 😂

Nice job. I’ve used solder butt connectors before too. I’ve moved back to crimping lately. If it’s good for aerospace and military applications, I’m sure it’s good enough for my ride. I’ve seen issues with solder, so why not stick to something that works. I use heat shrink to keep elements out and expect that connection will be good until the wires rot away. I like the switch idea for the halos. Mine only has one halo ring unfortunately, so I am adding a relay to switch my halos off with turn signals. I had to grind off those same tabs on my lights (Oracle lighting) to get a proper fit, and drill a small hole in back for light vent, but otherwise, similar nice fit. Anyway nice job. Great looking mods on your car!

Thank you !

I fixed my ice maker doing this. My wires on one side were red and black and the other side white and brown. I put the red and brown together and white and black. It’s making ice.

Thank you! I followed what you did, except just used the wire i cut going to the left and connected directly the the right side.

Very cool! Now I'm need a Pizza. Looked so good.

Thank was wondering if i could use my old immersion heater with the tub! Used it 30 years to heat my horses oats in winter

Great vid. Shows just how extensive a 'simple' body rework and paint can be. Not just a scuff and shoot on these classics!

Great Job!