Video

Hi Mr Rockwell, unsure if you will reply after 2 years, but do you have a rough value for the amount of current that the camera draws?

It’s a little bit all over the place and for a new bee you don’t show everything

Thanks

For a long range flight is it really good? fpv model airplane flight

Thank you great video

Thank you for this detailed explanation. Would you make a video on the applications you are using for these batteries. I am going to use mine on an EDF Jet 90mm. Would a 6s 6p of 4500mah and 50A be enough to keep the jet in the air. Also would you explain how the readings during flying of these batteries work? In Lipo I start landing when the 6s announce me a voltage say about 22v. But I noted in case of LIion the reading is 2000 , then the pilot said still 1500 and it’s time to land.. I am not sure what the number 1500 he was talking about, is it mah !? . Also , how these batteries are rated 50A, then the pilot says he was able to pull 120 amps, are the Amps of each battery added together? Many question marks ⁉️

Hej, odličan tutorial prijatelju! Svaka čast na ovim informacijama. Btw, vidim da si iz Osijeka, ja sam živio prije na Jugu2, odmah sam prepoznao polj.institut! Nevjerojatno! :) E, samo još jedno pitanje - pretpostavljam da je ovo 4000 mah? Novi sam u svijetu BNF dronova, pa oprosti ako je glupo pitanje. Napravio bih sam 8000 mah za Chimera7... nedavno mi se orig.baterija prilikom slijetanja drona oštetila, i jedna od šest ćelija je riknula. Molim te savjet frende! Sretno letenje želim! Pozdrav!

Hello thx for this video but which uart to activate on betaflight for esc? :/ please

Great video. I’ve been wondering how to build an xS2P battery in that configuration. Thanks 🤘

Hello Mr rockwell, hav you ever fabricated a 6S2P battery? if yes would you have a diagram to share? thank you

what nickel strip thickness did you use in this pack ?

Where to put last balance charger wire? (first after red) On cell no. 8 ? On charger says one cell is at 0.00V Why?

Does it matter what wires your using to connect the cells

I'm not sure how you went from 3 black balance leads to 5

How do I wire vtx? What uart?

still is a somewhat respectable clock speed today 😭

Great way to explain the conections, ty

why not bms??

The radiation field is also big?

What kind of tape is that you used to tape the ends of the batts and tape the batts together?

Hello, I purchased 2 BLITZ E80 Pro 4-IN-1 ESCs and a BLITZ F7 Pro Flight Controller, but I have a power problem for my DJI VTX. I thought it was a defective card, so I bought a new BLITZ F7 Pro Flight and I still have the same problem. I tested my VTX directly on battery, it works. Can you help me please

What gyro cw do u use in betaflight 4.3.1?

What antenna is on your VTX

Should I use these batteries for a 6s2p pack for 7" drone ? I calculated the weight = 840g. Where the 18650 @6s2p = 528g. That's 312g more if I use the 21700. Which one you think I should use ?

It's Great when one can find the *Very* Spot Welder that I'm after! I'm watching and listening avidly so far and it looks like I am buying it via ebay! EDIT* Absolutely worthy of a Sub and a Like for good measure!

nice, do you have the link to the 3d printed part?

That thing is massive 😂. Wow i have the small one. I didnt know they got that big lol

Did you used to have a "how to build a 6s2p pack" video up and take it down? I could have sworn you had one up!

Lol looks like it’s falling apart inside left area by the nose 🧐

Very calm and complete video. thx for that ^^

So this is not with mpu6000???

the cable which connects the ES. and the FC it's correctly wired? I think you have to change some cables which are not in the right position.

The iNAV not working on this controller. Wery pity...

Since it's bridged both sides negative. Both sides positives. Connecting both negative to positive on both sides just for extra current? Hard to explain Guess this why I seen nickel steps in box shape. I want to do a 6S2P or 3P or 4P Just nervous. I want to use molicel p45b

How is the spot welder after 2 years sir? Are you still using it?

I want to wire tbs diversity nano, but I am already plugging the air unit in the two ports next to each other, tell me where to plug the tbs diversity nano receiver? Thank you 🙏🏼

I finally made my 4s2p 18650 pack thanks to you and it works great I used sanyo 10amp 3500 mah batteries, I now want to build a pack with same configuration but 4s 3p whats your thoughts on this please? I'm trying for more mah. But if pack is any taller the hatch won't close on my ar wing pro. Any advise would be appreciated. Thanks again

Great video!

how to make stick?

Hi, I've got the same module, first time I powered it on I waited about a minute (cloudy weather) and it got 3D fix, the blue light lit up. Next time when I power it on I get solid blue light immediately and I can't get GPS fix. Also GPS tab in betaflight now doesn't show any sat signal levels or any other signs of activity. Do you know what it can be? I can't find anywhere what does solid blue light mean on this module.

Very helpful! I WAS scared to try this until you showed the WAY!!!!!!

I will be doing this, should I pre charge any of the batteries and if so how much and which ones? Would be good if you could respond asap

Did you use the 4s2p 18650 pack that you built for this flight? Seems like low voltage most of flight. Thanks for all your videos

Can you help with a question? Why do you have two sma inputs on the antenna?

Have you tried this 6s pack in your wing? Just wondering difference in the 4s2p 18650 pack vs this pack in flight? Thanks

I'm also building this same pack for a ar wing pro, just wondering roughly how much flight time you get with this pack on your wing? Thanks

😒 𝐩𝓻Ỗ𝓂Ø𝓈Ｍ

This is only video around on how to do 4s2p 18650 what were calling a stick battery pack so thanks, I'm going to give this a try as soon as my batteries arrive and have watched this several times but still worried about folding it up just somewhat confusing, so i guess on the balance leads cell one will show one cell voltage, cell 2 twice the voltage and so on are the cells in order I mean side by side? Great video thanks new subscriber

i have a yellow led on what does it mean ?

What a firmwire mess Hobbywing! So in the end correct target is "HOBBYWING_XROTORF7CONV" , or "Hobbywing f7 con" or "FFLYOOF7DUAL" , just change the manual guys?! Thank you for the video! HobbyWing should produce one to set things straight about this board. O, and what is that nonsense about "Zadig tool" we must use first...