Video

Dang thats super unlucky.

I have the same problem, but mine is totally burnt. I tried to remove the mosfet and it worked fine, but the light indicators is not turning off even the lights are powered off. Draining the battery, what should I do to fix it? Thanks

Bruthaaa eeuuuuuhhh.....

Gooch ball 5.0

Bros got an ant colony in his fan

Hiya. Newbie here. I see that next to the BIOS chip it is marked as U12 on the pcb. Are all those marked as 'Uxx' bios chips as well? I was looking at a WD PCB and do see U21 and U23 quite close to the MOTOR IC. U22 seems to be next to the RAM/MEMORY I am looking high and low for MOSFET/FET chips but am not able to identify one. Any advice?

Kindly help me out where to download the diagram for the macbook pro

DONT ORDER 5000 AT A TIME AMIGO

Aigh

maybe you can help. i hooked up a power cord to a HD and apparently it was backwards.. how do i test polarity so i don't do this again. and i think i need to swap a BIOS chip but how do i know what donor to get?

Thank you for the video. My old MacBook has not green light and is not charging, but it works fine when the battery has charge some juice in it. I'm gonna wing it and try replacing the ISL6259 directly. Let's see how it goes XD

I appreciate that you mention calibration and clearing the codes. It would be awesome if you would post a video showing how to perform both of those tasks.

I'm going to attempt to do this to save a hard drive. I wonder how important is the size of the nozzle in the heat gun? I've bought a heat gun from amazon and the only nozzle it has is 9mm diameter. From your video it looks like the nozzle you used was smaller than that.

19:40 what did you change the temp to? and airflow?

They definitely do it right before bringing it in

You have some unreleased anger

Ende pre mim essas placa com defeitos

yes

Can't believe they clip though the case

Bad boi. No beef with the hdmi port 😡

16:15 are you looking threw the microscope as you do this? Or are you looking at a screen? 16:50 what is a fillet? my volume all the way up and can barely hear you

I let a shop change the chip but it shows still the wrong hard drive. The chip definitely got changed but it is as if it has the wrong board(new donor board) even if it has the BIOS from the old board. Any knowledge why this could be? Board was the WD 2060-800067-001

That reminds me I need to buy some of those roach clip board holder things

Really enjoyed this fix!

Buena explicación

Where can I get that replacement part?

Hey just wanted to let you know I was able to fix my laptop which had this same issue. I used a small blob of solder like you said in other comments and it worked! Thanks dude.

What can I do if the solder on the capacitors doesn't melt?

Do you perhaps have a link/website? I ordered exactly these but received the wrong one. They are rather dark brown and the width of the caps is equal to the depth

Dear, I have same model laptop, power on Apple logo appear and restart and off 20v and 0 amp, pls. help me out where I have to check thanks....

Awesome video

hi, do you know which capacitor I need for the mainboard 820-00875-a (a1708), I can't find anything about it

great video but what happens if the bios chip is not near the end of the board as yours was? how is the heat applied then?

I hate that bios chips are even a thing... NO ONE is able to swap them from my donor board around where I live so I spent $100 to do it myself... Thanks for making this video.

How much does a respectable technician charge for this service? If I provide the new board and the faulty board.

Is there anywhere i can send my board for the bios to be swapped. I got a new one from ebay, and blasted both bios chips with 450 degrees, 550, and 650 for several minutes and neither will budge!

You started with 325-350 temperature but increased it when the chip did not come out. What was the final temperature you used to remove the chip?

Hi ikow this is an old post but hopefully I can get some reply, Is it the backlight on the screen is the problem with this one cause thats the problem I have .Thank you

Hi friend do you have bios? Thank yoy

Simple and Beautiful Work, tks.

GOod afternoon, hope be well, i have an HDD of 320 Wester digital caviar blue, at work i have one broken with the exact same board part. My HDD is recognized by the motherboard, but i cannot get access to the data or info of partitions and disk capacity, If i do the change of the board can i get back the info stored? if i disconnect the disk suddenly appears the capacity used but of course i cannot access.

Did you ever upgrade the battery pack? I just bought two 18650 3500mAh 10A batteries that say they have an integrated protection circuit built in. I guess I don't need to reuse that circuit protection strip? Looks like I'll have to mod the battery compartment a little to accommodate the slightly larger batteries.

Que valor numerico tiene el componente U1, seria tan amable por favor. Que el de mi lampara se exploto y no tengo manera de saber que datashet es.

I want to do a swap plate, can i use the board that came from the old plate into the donor drive?

thank you for being the only video on youtube that helped me fix my speaker. Had no clue how to take it apart, the sound was distorted, and it wouldn't turn on unless it was on charge. I took it apart and everything magically fixed itself.

Hello thanks for the great video I have the exact same issue but do not have the original PCB anymore. Is there a work around? Thanks!

Can you fix a nitendo switch with a wifi module that isnt working even thought it was never opened before?

i got the same board works fine but no light and will not charge nice video though

My g14 has a flickering brightness problem at 100% brightness it flashes bright then dials down what could be the problem?

Thank you for making this video. I have this exact same worklight and have, what I believe to be the same problem that you had on this video except that on mine it's much more obvious because the mosfet is burned. I just need to get a new mosfet to fix it. Also I've been thinking of replacing the charging port with an USBC one. Have you tried this?