Video

Very nice video, soak the ends in a cup of hot water for a few minutes and then they will slide on more easily?

Two of our zones run across the slipped area from right to left. We have noticed that there are sections remaining dry. Would the angled nozzles be better on these sloped sections?

Extremely helpful. Thank u

This video could have been done in 3min. Way too much non value added talk

Thanks for the explanation. I thought this would solve my problem, but I didn't. I have a Rainbird 5000plus that doesn't spin. It comes up when watering, but only sprays in one direction. I can adjust the radius with the screw, it can be turned from right to left and back. I took out the head and cleaned it with water and found no abnormality, put it back, but it does not turn. Water pressure is fine, other heads work fine. What could be the reason?

What do you do with the remaining wires that you don’t need on the solenoid end. Tape it with electrical tape or leave open?

Do those solenoid valves go bad and cause the system not to turn on?

What if i had a 1 amp solenoid? Would a 22 Gauge be enough? I feel like 18 is to thick.

recently had to do an extraction. This tool didn't actually work. Took a Kershaw folder knife jammed it in and bingo. One twist and out it came.

Had to change my parents sprinkler. Huge help and major time save. Thank you.

Great video! A couple ?? 1) to move the left stop clockwise - the reverse of what you did - going from 9 to 8 o’clock - you have to turn it counter clockwise 7,6,5….10,9, right? 2) I’ve seen pros twist the head counterclockwise to move the left stop like you did. But while sprinkler is working. I think I read that you shouldn’t do it with water on. Thoughts?

Omg thank u so much!!! It was so easy! Your instructions saved my girl life ♥️♥️♥️♥️♥️♥️ sending you lots of love ❤️

……. absolutely no help whatsoever ..,…..

This is the single most useful channel on CZcams...

Thanks man. Just fixed mine with these instructions 👍

How do you shorten the distance?

THANK YOU!!!

THANKS ever so much! This widow SO appreciative.

It’s incredible how no video anywhere explains what to do if the rotors are spinning the opposite direction and then won’t have any stopping point

"Fuse" reads in zone one and won't turn on. I've unplugged the system; it worked once, but it went back to reading the same for zone one. Can't find fuse to change. Any suggestions?

THIS VIDEO WAS EXTREMELY USELESS! UNLESS YOU SHOW HOW TO DO IT IN A YARD SETTINGS! WHAT'S THE POINT! I COULD NOT GET IT DO ADJUST WHILE THE SPRINKLER WAS RUNNING!!!!!

Thank you for your video!

Thank you!

Tyu sir ! A great explanation!!

Is "funny pipe" the same thing as "swing pipe?"

Why not use 3/4” funny pipe instead of half inch? By going 1/2” you are effectively reducing the water flow to that sprinkler head, right?

You tell us “Do it the RIGHT way so it doesn’t happen again.” Well, then you should tell us what IS the right way within this same video.

Excellent point about how a 90-degree spray lays down twice as much water to an area than a 180-degree. Nice!

You may want to edit this video to add in some B-Roll close-up footage of the exact way to install that nozzle. Do you drop in the lower portion first or the upper portion of that red nozzle first and then snap it in place? You state a couple times the “45-degree angle” but you don’t tell us whether the bottom of that red nozzle goes in first or the top. I think some B-Roll close-up video there would clarify that and make it crystal clear. Nice video. Keep up the good work.

I’m in marketing, so I’ll say Excellent job in keeping it short and to the point; just the facts! Perfect!

Thanks a lot, showing these basic steps is very helpful for DIY beginners like me!❤

Does those nozzles fit on the rainbird 3504?

I have a white wire that’s been cut and I found it when the pipe near it got a leak. I think the guy who worked on my system cut both but I just found it. My system has 7 zones. Your wires are all in that nice black sheath, this white wire is super tiny and just laying nearby all on its own. I haven’t even found both ends. So frustrating. Can you tell me what to look for when I go to Lowe’s because I’m going to need more wire, I think I’ll have trouble getting ends to meet otherwise but not sure what wire I’ll need. I have the wire caps with grease inside then go into a larger encasement.

Thanks guy.

At about 5:35 in the video you mentioned that you were gonna talk about the nozzle. But you NEVER did.

Thanks man this thing was driving me CRAZY. instructions given didnt show the hole inside the arrow.

OK. Pardon my last comment. I see you have given me the link. I now have the chart.

How can I get a copy of the chart for my future reference? Great video.

How do you take the OLD blue insert out?

Did You Know Other Brand Of Sprinkler That built With Check Valve?pls

Worked like a charm. Thanks!

Where I Can Find This Valve , I Couldn't find In Home Depot

I Have Being Tired For Two Days Fixed That , I am Going To Go To Home Depot To Get That , I Hope Working For Me Too, Thank You For The Info

This is the problem I have, got your check valve but it will not snap in, these are rainbird heads

How do you connect the common wire if you have multiple valve boxes in different areas of your yard?

Straight and to the point. Very easy to understand. Thank you

Surprised you aren't using a nozzle pulling tool. Once you pull it up, you can clamp the pipe so it stays up and doesn't slip back in until you unclamp it. Best $10 I've spent on my sprinklers!

How to get a broken barbed end out of the hose? My 90 degree broke right at the elbow and having a terrible time getting the barbed end out of the hose.

So nice when someone can explain things in a simple direct way. A true teacher.

Excellent presentation, thank you.