Galax GTX 1080 Ti Hall of Fame Graphics Card Repair - POSTs With No Image and a Backlit Monitor
Vložit
- čas přidán 5. 09. 2024
- I no longer accept electronics for repair. If you are looking for technicians to fix your electronics or repair advice, consider the newly opened GraFix Repair Discord below.
Discord: / discord
If you wish to have priority in getting repair advice at the discord server and be able to access the full server, you'll need to subscribe to the server's Patreon below.
/ grafixgpu
Everytime a HOF or KINGPIN card is repaired an angel gets its wings.
Don't forget the Lightning Series from MSI. The 1080Ti Lightning Z is also a very good OC card and runs very cold.
@@basti8878 Absolutely! I have a MSI 980 Ti Lightning and i love this card, im sure its the best 980 Ti ever made and i never got more than 62 degrees on full load!
Your skills are unbelievable, a living GPU encyclopedia, what were the odds of
the fix
that reveal of another hall of fame 1080ti was hilarious lol
Man, As an enthusiast, I really love those type of videos.
I am by no means an expert or know how to repair cards, but, I know where to send my card when it dies out of the blue on ambient water cooling overclocking session !
Somebody doesn't know the difference between an ohm and a kilohm. They meant to put in a 116 ohm resistor, and put on a 116 kilohm resistor. Lol, a very subtle difference, just . . . y'know . . . 3 orders of magnitude.
Some poor probably underpaid sweating Chinese electrician you mean xd
Generally speaking resistors should never be measured in a circuit as other components interfere with the reading. For smd components, if one pin is grounded, the best is just to move it out so that only the ground pin is connected and take the measurement.
success, well done! the closing summaries are nice.
If there were captions for these videos it would just be words with no spaces.
All killer, no filler.
I don't think neither of us would mind a longer video. If possible I would love to see all the steps you take.
Hi Tech, this video is certainly not too long. It is just packed with useful information.
Crazy PCB, also love how the power connector has burn marks on it. Of course it does. I'm glad this beast gets another chance.
Hey man , your vids are awesome.
You explain things clearly and straight to the point !
Cheers
Love the way you explain everything in depth and helps me a lot in diagnosing GPUs. Keep it up
Should have checked for bad caps to see. If that's why resistance was so low
I have a problem with my GTX 1070 gigabyte. Sometimes it boot with black screen on the moniter ( imean moniter is turning on with blacklight screen). What could be the problem? . Please help me
I have a guide video to run MATs. You should watch it.
@@TechCemetery but sometimes it's working 100% fine with no memory errors and nothing just working 100%
can you please make a video about how to use the pcie socket tester in order to detect if the cpu is dead or not, thanks
when u pull up your another HOF card it make me wooowww lmaooo
Great video! Love the MS paint schematic.
I liked that you are adding jokes it the video
it makes your videos more interesting
keep it up!!
Well played I wish I was as smart as you, I have the same card, today I herd a pop and some smoke came out, computer turned off, tried again same thing, removed card and computer turns on. Is there any chance the card could be fixed or you think it's definitely dead? Or could it be the PCI express slot, I can't check till tomorrow, I tried to take the top plate off the card to have a look but it broke the thermal paste so I have to get some more.
Hey man i have a question. Love your channel btw. I am wanting to learn gpu repair myself, although i find it pretty difficult. How did you start learning? Trial and error? Watching CZcams vids?
Thanks in advance
oh wow that's a cool looking card
Hello, does anyone know what Heat station he uses?
Big fan bro....@Tech Cemmetry!!!
YOU ARE THE BEAST, I LOVE YOUR VIDEOS
I bought a $60 EVGA 1080 Ti SC2 Black Edition today and it's got a similar issue... Card doesn't seem to get any power. Fans don't spin, no output, PC doesn't detect it, but the PC _does_ boot... Any idea what the issue could be? I know you have another video on an SC2 1080 Ti but that one was for PC not powering on at all
Thank you!. Love your vids especially since I happen to have 3 broken video cards. :) I have 2 x GTX3070s and no idea what the issue is. One artifacts after some time especially on some games, and the other one just goes to a black screen (no video signal) during game play. Its not a heating issue with either as it can happen very quickly and monitoring shows normal temps. I have checked all voltage rails are ok. And memory tests show no errors :( I have no idea.
For the artifacting one it's memory.
2 dead 3070's?? Jesus, 30 series really likes to die huh? 1 year old man...
@@TechCemetery How do I figure out which memory module? Running the memory test shows no errors.
200 ohm when it should be 800+ and a normal dead GPU but still fixable?!! Never heard of before, I would really know the reason for that!
Awesome video
Hi,
I have a palit jetstream 1080ti. I found out it has only 20 ohms on PEX rail. What can it be? Can you point me out please?
Oh a rare white pcb, nice 👌
Hi, I really like your videos. Keep it up with the same spirit.
I have an evga gtx 1050 ti sc and I have a few questions.
1. All measurements are fine - voltages, ohms, but there is no image on the screen. I tested with mobo with second PCI-E with another video card and in the device manager shows it (1050 ti), take the driver, but immediately after that it gives me the exclamation mark and code 43. After the system restarted, when I went to check the manager, the exclamation mark disappeared, but there is still no image.
2. When I open gpu-z, it gives me almost nothing. 0 mb memory, no pixel shaders, no sensors, nothing specific. I tried using a programmer to flash the BIOS with several revisions, but with no success
So I suspect a few things:
1. The BIOS chip itself
2.Bad memory bank
3. The main processor itself
4. Bad resistor on the line to the BIOS
I know it's hard without the card in front of you, but I'd appreciate it if you could give me some advice.Thank you.
I see he couldn’t be bothered answering your question. Typical big ego, no personality individual.
I've always wondered... would it be possible to solder another 1GB memory chip onto a 1080 ti and make it 12GB after a bios/fw mod? Or how many components (if any) are missing besides the chip?
That is a beautiful GTX 1080 TI PCB
I have a Radeon RX 5600 XT 6gb, the card is mine if i manage to fix it, but can't figure out what to do, and goes like this:
It has 4 ports: 3 Display ports and one HDMI, literally one of the DPorts is toasted, burned, the others ports are visually intact, when the card is put in the motherboard it don't give up any image (in the screen appears: No Signal), no beeps are heard, AND the PC starts as ever (i know because the intro of windows sounds normally), i try without the fans shortly and the card don't warm or heat at all, when i put the fans these move, but the rest of the card is still cold, any ideas?
\Hello. I have gtx1070which have all voltages ok but not detected. Reflashed vbios, reflowed, but still not detected. Any hint?
Love the videos as always!, ive got a gtx 1650 that had a short on 12v replaced mosfet drivers to remove short, all working except card only seems to get to 40 degrees and its showing 240% tdp around 250 watts from the pcie connector and had 1 single 6 pin plug on it, any ideas?
Watch my Strix 1080 Ti video where the card is stuck at 139mhz
@@TechCemetery the clock speed is showing the 1500-1700 range, could it still be same issue?
It should be similar.
@@TechCemetery cheers will have a look, cant see an INA 3221 on the board any ideas what else it could be labelled? thanks in advance
@@rosspaginton8212 Some of the Turing cards use a different chip called an NCP45491
can you plz explain error code 43 : cuda error, reset of oc memory required
Where do you get your "dead core well over 95% of the time" statistics? I wonder how many of those are actually cases where the problem was indeed on the PCB and technically repairable, but it was just too much work to diagnose and actually fix (like some random 0402 or smaller passive failed).
Experience and intuition and confirmed with a thermal camera.
i think he meant low resistance on that rail means bad day for GPU core. not any broken gpu has bad core.
Seem problem on titan x pascal, can you do a video
At 1:40 that caps are looking kinda sus.
What do you use for your rework station?
Would it be possible to include an affiliate link for the station in your next video ?
Thank you
Quick 861DW. If you use the Amazon affiliate link in the description and search for "Quick 861DW" and purchase it, I'll get a commission.
I have a really similiar issue on a asus vega 64. Where i cant get the memory voltage. Aits around 200 mv only. Any recommendations ? It does not have the doubeler thing but a normal vrm
that card already looks very sus with those burn marks 😮
Sir I have 1070 graphic card its working but not detecting I search for troubleshooting I got one shot component but I don't know what is it the name mission on it (470 75cra d) sir please help me
Great reapir, I wonder what happened to that resistor, those fail so rarely!
BTW, anyone knows the 2070 Super correct core resistance on 1V rail?
Roughly 10 Ohms
@@TechCemetery Thank you :) I was told that the chip is dead, but my suspicion was it could be just very small resistance:)
PEX is very low on modern GPUs, as long as it's not below 5 when the GPU is at room temperature I wouldn't worry about it.
I like so much your videos
bro do you know good vga card repair helping forums ?
I have GTX 1080 ti that won't power on I found a burned chip.how can get I get the board PCP schematic for the board to no what to test
You won't since they are not released.
your best bet is to find one of gpu technicians, for repairs. we are plenty and we all have discord channels to get in touch.
@@Dmiliunas What is average usual price for repair?
I have a 1080ti with a short on the base 12v rails, no visible damage, what would I check next?
Assume it's a MOSFET or Powerstage. I have quite a few "Computer Won't Power On" videos you should watch.
@@TechCemetery thanks, will go and check them all out
I have a Titan X than I need to repair, can I send to you?
hi . can u help me with a question?
Ask away
Hey James
I hope you are well
Who can we contact in the European region for repairs ?
Alternatively I can send my GPU to you
Thanks
My discord server is linked in the description. There are a couple Technicians listed who live in and around the EU.
Ger repair does gpus. hes good technician. come to cemeterys discord for more info
*slow claps*
cfa
Good job!!! greetings from Greece!! I know its a bit awkward demand but if u please talk a bit slower. For me not have native language English i need to stop and repeat some times the video.I know your brain work like this too fast that's why u talk too fast but not all people can follow :P ( i know there is a speed option in video but i like to have it normal ).
You can adjust the video playback speed to 0.75 or lower to slow down the talking.
Shit.
You talk too fast
watch video slower. while he does talk fast, it helps to keep video shorter, and some ppl are naturally fast talkers. we all are different and yet we all are the same :)
Why are you talking and mumling so fast??!!
ZOTAC GTX 980 4GB blackscreen when i install driver what is possible issue? i tried old and new driver same issue