HONEYWELL HOME T3 THERMOSTAT WIRING CONNECTIONS AND SETUP
Vložit
- čas přidán 24. 12. 2020
- RTH6360D1002 Honeywell home T3 / home owners thermostat get it at most home improvement stores. How to wire it up and configure it to your specific needs weather he 1 heat only, 1 cool only or heat pump
MY Amazon Affiliate links
Get It here 👇
amzn.to/42JoGBn - Honeywell T3 thermostat
#d2dnyac #thermostat - Jak na to + styl
Thanks this video help me to fix my new thermostat 👍🏻
Glad it helped
Oh my goodness!!! This video was SO incredibly helpful! Thank you so much for talking the time to explain each setting & the associated wiring. Life saver!
Perfect video. Took just minutes to do. I only had 2 wires and a jumper so the comments and replies were very helpful as well there.
Thanks for stopping by
This video was super helpful ... Ive got a 2 wire setup for a ducted heater here in Australia and I couldn't figure it out till I watched this video .. A simple R to W connection made everything just work .. .Thanx again :)
Good job my friend
Thanks for stopping by
Thank you. My ancient floor heater wasn’t working with the schedule. So I watched your video and programmed it to no schedule and it turned on. I could not get anyone out here to work on my heater. It’s winter here and I have been using my oven to heat my house. Thank you so much again.
Thanks for watching
Great video! VERY informative for the DYIr. Thank you.x
I was a little bit frustrated because I installed a DIY heat pump system and when I put my thermostat in cool, air was coming out hot and vice versa. You saved me the day! Thank you!
Thanks for watching
Thank you!! This video was extremely helpful.
Thanks for stopping by
I am so grateful 🙏 thank you for this!!
Thank you for watching
Excelente video, thanks ,I set up my thermostat watching this tutorial
EXCELLENT detailed instructions! 😁
Excellent video,thank you!
Thank you for stopping by
This video was great! Thank you
Thanks for watching
Thank you! You helped me a lot!
Thank you for stopping by
Good job this video is awesome
Thank you soo much this helped me a lot saved me from calling a tech 😊
Thanks for watching
This video help alot thank you so much
Thank you for stopping by
Big up general u just save my life
Thank you for stopping by
Blessed love breddrin. Your video help me out big time.
Thanks for stopping by
Thank you for the breakdown
Thanks for watching
Thank you very much sir. Good job
Thanks for stopping by
thanks for your time
Thanks for watching
Thank you so much!
Thank you for stopping by
Thank you 👍
Thanks for stopping by
You the man 👍🏾
Thanks for watching
Nice
great vid
Thank you for stopping by
really helped ty
Thanks for watching
Thank you so much for this! It didn't exactly match my failed Bryant thermostat wiring, which I could find a wiring diagram for, but I couldn't find one anywhere for this Honeywell, and wasn't getting heat out of my heat pump. Thanks to your verbal wiring diagram, I'm all set now!
👍thank you for stopping by
Boss brilliant ! Sounds like a yaaaad man!
🇯🇲 💯 thanks for stopping by
Saved me also, i couldn't figure out why it was sending a signal to turn on the compressor outside. Had just the inside coming on.
Thanks for watching
Very very helpful from a DIY’er. Many thanks.
Thanks for stopping by
Nice informative and clear instructions. I purchased the RTH6360 thermostat. I have steam heat with two wires coming from wall, which terminals do I use? Thank you in advance.
R and W
Thanks for the tutorial
I'm installed a T3 programmable with a heat pump is you explain where the wires go that is fine but in may case only have 5 wires to work, The previous thermostat had the RH jump to RCR and W2 jump to E is in the instructions said no jumping wires whats the next step
Okay so with 5 wires you had terminals RH/RC . G. Y. O/B. W2/E connected on the old thermostat?
Please give a better description of terminal connections used on old the thermostat
Just note what wires are connected to your thermostat before you remove it. My thermostat used the Blue wire as the ground wire and there was no black wire. They might have done that because it's the Downstairs Thermostat. If you take a picture of your old Thermostat wiring that makes things easier. Your old lugs are labeled so you will know what function each wire has even if one might not be the same color. The installer might have run into a bad wire in the harness and used a different colored wire in the harness instead.
Good
Good job 👏 mine is working fine but l am having problems with the fan. The fan is set to auto but it keeps running. What should I do
Does it continuously runs?
Does it say heat or cool on on the screen?
I have a conventional setup for my thermostat(multi stage heating and cooling). In my older thermostat Y2(black)Y(Yellow)G(Green)C(Blue)
W2(White)W(Orange)R(red one wire) and it works. When I wire it the same on the T3(R one wire tab up for RC) Convnetionial Forced Air Heat and Electric Forced Air I get nothing but warm air on cool mode. What could be the problem?
@Sawyer Mookie does the heating work?
What if you have a heat pump system but you have an auxiliary cable also?
Thank you so much for all of the information and understanding.
I changed the stat in my apartment with a heat pump set up. I have double checked my wiring and made sure it is correct. The issue I am having is that I am not getting power to the stat unless I have batteries in it?
It’s like the power supply isn’t working . Yet the stat is functioning properly once batteries are in it. It’s got me scratching my head. I was wondering if you could help me out?
Is the C wire connected?
I wish I could upload photos to CZcams lol
Yes the c wire is connected
This model told me I had to have batteries bc the supplied power wire setup doesn't work on my model RTH6360D1002
@@billyjohns7258 thank you dude!
Yea I ended up coming to that same conclusion but dear god that was confusing.
I ended up hook a voltmeter to the wire to figure that out haha!
They only put that on the 16th page waaaay at the bottom in brackets. Fun times
My old two wire setup had W and R connected. With a small jump wire from the R to RC. How would I duplicate this on this new model? Or do I even need to?
Just connect one wire to R and the other to W and you are good to go
D2D NY Real World HVAC Simplified great advice. It’s up and running. Thanks for the tutorial.
So if I have just plain ole furnace heat with radiators, all I have to do is connect the R wire and the C wire ?
I have two wires to work with.
R and W
I have followed your settings for the conventional but my heat/cool is not turning on. Do you know what could be wrong?
Was there an issue with your system prior to replacing the thermostat?
Have wood/oil combo furnace. Replacing wood thermostat with this. In the 205 program section which option should I choose?
If your furnace is forced air there’s an option for that! If it heats your home via hot water or steam radiator there’s an option for that, the type of isn’t relevant there’s no option for that
Hi, thanks for your video. I have 5 wires controlling a heat pump with aux/ emergency, and A/C
White, red, yellow, green, blue. There were 2 jumpers W2 to WE and RC to RH. I see you said the T3 thermostat takes care of the red/24 volt just needing one.
Does the same apply to the W2 to WE jumper? My Aux is blowing cold. The blue wire was on O/B so I put it in O/B
Should my white wire be moved to W2 ?
O/B must go to O/B from old to new!
Set 221 to 1 and put the wire from w/we to E so now you can turn on that backup heat from emergency heat mode on the thermostat
@@D2DNYAC ok thanks got it all wired correctly and it is working. One question in the emergency mode it runs 3 minutes every 10 minutes. Is there a way to adjust the cycle rate on the T3?
That was on a 40 degree night just to check emergency mode.
Just bought a Honeywell T3 thermostat. My old Honeywell is not reading correctly on the temperature, AC companies said I should replace it. I only have four wires, white for heating, yellow for air conditioning, green for fan, red for power 24 v. Seems pretty basic white to W yellow to Y green to G red to R. Hooked mine all up to the gray shaded plugins. Something's wrong my blower turns on and my heater but not my air conditioning cooler. All the wires were stuck in correctly nothing loose. Do you have any demonstrations on four wires, what could be the the problem, I ended up putting my older thermostat back on everything works.
Based on what you’re saying 2 things .The grey slider between RC and RH /R ( it should be in up position) or in the configuration/ setup menu you selected heating only
great video, mine will not start forced air/heat only?
Perhaps it's not the thermostat, try fan on option, if that works you should consider calling a pro
I’m having an issue with where to add my wires. My current thermostat has R-red, Y-yellow, G-green, C-Black, O- orange and W-white.
I’m not sure where to put the wires for heat since the instructions say do not use w. Where do I connect my orange and white wires?
Do you have a heat pump? If so connect all wires according to how you remove them from old thermostat and place the white wire on E emergency heating or w2 auxiliary heating
My old Lux system on program waits for the correct time before it turns on then turns off when the correct temperature is reached. Turns on again if it drops a degree or more, maybe more than a few minutes.
This T3 starts hours early and it turns off when it reaches set temp and turns on again for a minute to keep set temp. It will stay off longer. Is this normal and is the short heat cycle bad for the furnace? I dont know why it turns on again even if set temp is shown.
Sounds okay, looks like the thermostat is "anticipating"
Why is my thermostat not responding. The display is on but when I select fan on nothing happens. Thanks for your help
Perhaps it’s not your thermostat the issue!, did you hear a click in the thermostat after putting fan to on?
Great video! After it's installed, how do you remove it to replace the batteries? I don't want to break anything when I try to remove it. Thanks!
Just simply grasp it firmly and pull off the wall!
@@D2DNYAC Thanks! I didn't want to force anything. I appreciate your help!
@D2D NY Real World HVAC Simplified. I have a question i recently redid my thermostat with that exact model. But it keep on switching between hot and cold air. The old thermostat had jumper wires. In the manual it says to take the jumper wires but never says to put it in the new thermostat. Do i put the jumper wires into the new thermostat??
Check the mode selection it maybe on auto as opposed to cooling or heating!! If by jumper you mean rc, rh / r thats read done by the slider on the base being in the up position
How do you chnage the settings if you already hit done
Re enter the setup menu
If old thermostat has a jumper between Rc and rh do you use on new thermostat ? Do you set to 1 wire and red goes into R ?
@David Smith on this thermostat the jumper is built in so just connect R!
It says cool and auto fan on the screen but the fan continuously running.
Iam going to change to vine 610 or vine 919.
Which one is better out of the two.
What happens when you turn system mode to off?
Old one has a Rc-red wire and a jumper to RH do I just slide it down and put it in RC? Or will I need to put it in R and jump it to RC?
Don't touch the slider and you will be fine!
I should probably watch the entire video before commenting, but one of my wires aren't the same color. Im trying to replace this old thermostat, it's old maybe 1970's thermostat. The wires on the back of the original one all correlate to the colors of the wires. The only one that doesn't is a beige wire running to w2.
Well put it on W2 on the new thermostat
Can you help me please?
I’m trying to replace old Honeywell to T5 Honeywell and I put all the wires to their matching. the heat works but the cooling is giving me heating too.
I don’t know which wire should I change?
Red-R
Green-g
Yellow-y
Black-c
Orange-o-B
White- w
Also have 2 more wires in the old one but their wasn’t attached to any wires: blue and pink .
Answer in the video you have a heat pump system it appears!!
I am replacing an old Honeywell thermostat that had three wires to it. It had a total of three wires. A red wire to the R terminal and both a white and a black wire to the W terminal. How do I connect the Honeywell T3 to these three wires?
@alberta high school chemistry just mirror the connections Red R and both white and black to W then in the setup select heat only and 0 cool
@@D2DNYAC I attached the black wire to the W connection and the white wire to the W2 connection. Is that wrong? I have a fan running, but no heat.
@albert high school chemistry unless you can verify where / what terminal all wires landed in the actual Ac / heating unit put the wires
On the new thermostat as they were on the old thermostat.
Got the 300 setting to 1 but I don't know how to set the heat/cool temperatures
Use +/- buttons
I have the two wire set up on r and w and my new furnace keeps turning off before it reaches the set temperature. The Honeywell says the furnace is still on. Can you help me?
@kelvon Keene sounds like the furnace is the issue! How much degrees of temperature difference between actual and set it cuts off?
My thermostat was ripped out of the wall. The wires were still in the black terminal from previous thermostat. I noticed i had 2 whites in same terminal. The black wire is coiled up amd wrapped back
Always match wire for wire when replacing your thermostat
Put my red wire into R and no movement from the unit outside. Then moved my red wire to RC now my unit outside works.
(My old thermostat had a jumper)
Can I leave the red wire in RC or should I have a different wire in R as well?
Thanks!
If the thermostat is only used for cooling, then what you did is fine. However, the jumper is necessary if this thermostat is used for both heat and cool
@@D2DNYAC thank you for the advice! How should I proceed using a breaker? As it’s a heat and cooling system.
As the thermostat already has a breaker in the system.
Or should I return the thermostat and replace it with another unit?
^^
Hi I have 5 wire yellow, green, red, white and orange, I have Heather pump and I want to connect the thermostat rth6360D
Typically Y to yellow green to G red to R orange to O and W to Aux or best follow wiring configurations the old thermostat
I have yellow blue white red green I switch from old Mercury thermostat so all wires was used where do I put the blue wire at
@Thlvking Lol 😂 where was It on the old thermostat? Was it used on the old thermostat?
For heat pump, what color wires go to O/B and E?
It’s whatever color you choose to use of doing a brand new installation however often time technicians uses Orange if available
My old wiring has a jump wire connected to rh to rc how do i replicate that to t3 model
You don't have to it's already done internally! Just connect your wire to the "AVAILABLE" terminal labeled with any variation of (R)
I have a 2 wire set up, but have it connected to W and R… still not powering on. Any suggestions?
Whats not powering on?
Thermostat or heating system?
@@D2DNYAC it was the heating system… i got it to work now. Thanks
here's what I have on wiring on my old Honeywell. I have a heat pump with emergency heat.
G-green wire, C-blue wire, R-red, Y-yellow, W2-white wire, O-orange wire. I'm going to purchase the T-3 so should I wire anything differently?
Hi friend this thermostat has a designated terminal for emergency heat (E) all other you can duplicate
@@D2DNYAC the only wire that has me confused is the "c" blue wire. Is that the emergency heat and where would it go?
No the C wire blue goes back on C !!and W2 white now goes to E !!
@chris Williamson you must configure or setup the T3 thermostat for heat pump! And the only wire that you have to change is W2 that is now E
@@D2DNYAC I wanted to do an update. I disconnected the wires from my old thermostat today & I saw that the white wire was wrapped around the W2 screw & down to touch the E screw. With the new one up do I still put the single white wire in the "E" slot or the W2 slot? I know you said E in the other comments but I was asking if the E slot powers the W2 slot also. I bought the Honeywell t2 instead of the t3. thanks.
My system is heating in the cooling selection. How do I correct this
Watch the video over and pay attention to the heat pump setup and wiring
I have heat pump electric heat were do I hook the white wire does it go to aux or white and the common blue goes to common ok I have the new rth5160od1003 and when I put in cool my heat turns on
What are you doing?
Are you trying to replace your thermostat ?
When connecting wires at the thermostat be sure to match wire connections from old thermostat to the new if replacing. Otherwise you must match wire connections at the thermostat to that at hvac equipment low voltage terminal block
I'm trying to change my thermostat. I have separate O and B so I'm not sure where to place the blue wire
I would like to send a pic of the wiring for old Honeywell thermostat, how can I do that
What’s app 516 405 9628
@ Jody Neufville what’s app
Hello I have a question I have same thermostat , is there any option to keep the display (ON)( blue)
ISU / setup menu 1400 change it to 1! you will to have the C or common wire connected!
@@D2DNYAC I didn’t know how to do it can you please if you have any chance make a video about how you do it my thermostat is Honeywell t3
So I got two red wires, one from the wall to Rc and the other red wire is from Rc to RH on the old thermostats Do I do the same set up on the new thermostat T3 series??
You can ignore that RC to RH jumper !
Connect wire to RC only!!!! unless there’s 2 SEPARATE WIRES coming in to thermostat from the wall 1 to RH and 1 to RC then you have to connect them as they were from old to new !
@@D2DNYAC ok I got it,, thanks, I just made sum money with your help .. Good looking out
Hi, I hope you can help me. I have bought the same thermostat. Actually my old thermostat is wired as the photo I will attach. Usually the wire for fan is green, also I have 3more wire for speed of the fan. So could you please guide me how to do wiring.
Thanks
@Ali Zarrin Honar it looks like your air conditioning system isn’t compatible with this type of thermostat!!! Tell me the letters of the terminals on the old thermostat! And then I can advise you more!
The thermostat is like the one I sent in the link, but my wire colour is as I write.
Send pictures to me on what’s App!!
I have a carrier unit and it has Vplus and VG black terminal its only 2 wires.
I don’t think you can use this thermostat with that setup!
My old thermostat had a jumper wire and I cant figure out how to use it in the new thermostat
If it's a jumper between RC /RH / R then you don't need it!
@@D2DNYAC thank you.
Anyone know why my cool auto setting is not working, i have this same thermostat
Do you mean auto mode?
I have a green blue yellow orange white red I have I stage electric heat unit I have brought the rth5160d1003 I can't get it to work it's heating on cool
Do you have a heat pump?
It works too well. My heat is set to a creation temperature but the heaters won’t turn off once it reaches. For example I could set it to 72° but it’ll keep climbing and climbing to 78 how do I fix this?
And the fan is on auto
May need to call a pro
I have older system where there is 2 white and 2 red wires from wall, I know one white go to w and one red go to R but where do the other 2 wires of red and white go!
@Terrsa Norwood hard to say! Was all 4 wires connected? If yes to what terminals? If no only reconnect what was previously connected!
@@D2DNYAC one white wire was connected around one screw by itself then one red wire was connected with a yellow wire from the thermostat around screw then other red wire was connected to red wire around screw , other white wire was connected around another screw by itself
The cooling system is working fine but the heating is not working. The fan also keep running even though it is set to auto fan mode.
@VCS RADIO possibly its not the thermostat it maybe that heating system has an issue 🤔 especially if it's a furnace! Turn thermostat off if fan stops, heat system has a problem mostly likely, refer to my video and re check heating setup or configuration based on your situation , if it's all correct then call a PRO
I have a T3 and connect C and R but it doesn't work for me then would it be R and W?
IF there's only 2 wires and you have only heating system it's R and W
Muchas gracias, Thank you
Which wire goes into o/b?
@emmitt wyche Jr it depends 🤔
Do I need to shut off the power
It's recommended
I need some help with mine I had an old mercury Thermostat and upgraded it to this one. A/c worked great but the heat doesn't work. I do have a heat pump system
Did you connect the heating wire to the W terminal, that is the same wire you remove from W on old thermostat ?
@@D2DNYAC I connected the w2 wire to the w2 terminal on the new one. I have pictures of how the new and old one are wired if that would make it easier
Did you have W2 on the old one?
If no place place wire on W1
@@D2DNYAC yes the old one had a w2 terminal
I need help please. I’m only getting warm air. I have a heat pump. I don’t know how many stages I have or if I have emergency heat.
Most likely if this is a home ac it's 1 stage
Look at video again there is a section in the setup menu where I talk about heat pump reversing valve O/B what ever that setting is currently change it. Now you should be fine assuming the wiring is correct!
Thank you for your reply. We got the ac to run cold when we needed it the other night/day. But we now need the heat and it’s not hot air. It’s barely warm. Are you available on Instagram or what’sapp where I can send a pic of current wiring setup?
I am on what’s app my phone number is in the about section of my channel
I can't get heat and the fan won't turn off but it is set to auto
Looking like a heat furnace issue
Been fucking with this thing for 2 days now. It’s really easy until you have an old 8 wire setup😩
8 wires 😯 2 stage system then
I set it up but it only blows out heat
Do you have a heat pump system?
if we have heat only and it’s two wires, would it be r and w?
Yes
R and W /W1
thank you so much!
I had previously program my thermostat for heat now I am trying to program it for cooling and I am not getting it
Is your system capable of heating and cooling?
@D2DNYAC Good morning boss do I have to use every step that I am seeing on the video
@D2DNYAC yes I have a condenser fan unit in the backyard a evaporator and a 90 percent furnace in the attic
@D2DNYAC the system is cooling when when I straight wire it from R to Y the Tstat was controlling the furnace in the winter and I am trying to program the same Tstat for cooling and I am not getting it
What if I got 4 wires ? With the same exact thermostat, do it matter about color ?
@Greg Vidito yes and no! if you are replacing always match the wires from old thermostat terminals to the new, that is any color wire you removed from terminal R G Y W C and so on from old thermostat you must move to the same terminals on the New thermostat, in the even where all wire colors is the same you must label 🏷 each wire before removing it from old thermostat so as to know what terminal it goes on the New
@ Greg Vidito are you a technician?
My wires are just blue, yellow, red, and green. we can''t get the AC on. we had a jumper in the old one.
Not enough information here for me to advise!
I have a heat pump. My wires are g-green y-yellow x2-black B- blue R-red W-white . I currently have y yellow g green c blue o/b orange r red E black where do I put white? It's blowing hot air not cold
Hey friend assuming the first set of wires was on the old thermostat!!! looks like C should be black O/B blue E ( emergency heat if available) white on the new try that
And where did the orange wire came from????
I have this exact thermostat and my ISU settings doesn’t have 218. Is that bad? Lol
Are you sure?
My fan keeps running even on the auto setting. What do I do ?
@kylee Brouillard what mode were you using your thermostat or heating/cooling system in last?
Heat
@kylee possibly it’s a problem with your heating system if you have a forced air furnace! Does the fan shut off if you set thermostat mode to off?
My old heat pump thermostat has A(green) B (yellow) C (white) D (red).
I wired the new thermostat green, yellow, red and white in Aux.
I programmed everything in. Turned the heat on, and nothing happened.
@lynn McKinney we’re the terminals on the old thermostat labeled A,B,C & D?
@D2D NY Real World HVAC Simplified yes, sir.
I have ac only and only wires i have red green and white what shold i do?
Match the old thermostat terminal connections with the new thermostat
For cooling only it should be terminals R G and Y or Y1
@@D2DNYAC thank you I figure it out it was RC,Y&G. R didn't work.
How can you tell if you have a heat pump or conventional
If your compressor or outdoor unit runs to provide heating or hot air outdoor unit will have a reversing valve in it
The reversing valve is the deciding factor!!
Where does my orange wire go?? O/b?
If this is a thermostat replacement Where did you remove it from old, it goes the same place if O and B this is the same as O/B