Yaesu FT-857 Setting for FT8 | JS8 | WSJT-X | Digital Modes
VloĆŸit
- Äas pĆidĂĄn 28. 07. 2024
- I will show you what settings you will need to setup your Yaesu FT-857 for digital mode like FT8 or JS8.
đ Thanks for watching! Please like, comment, & subscribe. Please visit my website at: kn6bst.com
=============================
â±ïž Table of Contents:
=============================
0:00 - Introduction
0:12 - Extended Menu
0:39 - #19 CAT Rate:
1:23 - #20 CAT/LIN/TUN
2:11 - #36 DIG DISP
2:39 - #37 DIGITAL GAIN
3:16 - #38 DIG MODE
3:33 - #39 DiGITAL SHIFT
4:00 - #40 DIG VOX
=============================
đ Gear For Digital Mode
=============================
BaoFeng UV-5R Amazon - amzn.to/2DXAuJR
Yaesu FT-3DR Amazon - amzn.to/2PXU5M8
Super Antenna MP1DXTR80 - amzn.to/31XH1wd
External Sound Card Sabrent - amzn.to/3kJY9xT
USB GPS G72 - amzn.to/3gZq8Hr
Short Extension - Cable - amzn.to/2Y38ifz
Ferrite Ring Cores - amzn.to/2Y3dqQI
Audio Interface 6-Pin Mini DIN Cable DC-42F for YAESU - tinyurl.com/yaesu857datacable
CAT Cable - tinyurl.com/yaesu857catcable
Raspberry Pi 4 -amzn.to/3iIRlyS
Filming Equipment
=============================
đ· Gear Used To Make This Video
=============================
Camera: Fuji X-T4 - amzn.to/2Y3jJUy
Camera: Fuji X100V Silver - amzn.to/3kLZq7w
Lens: Fuji 23 mm f/1.4 - amzn.to/31Y84qW
Lens: Fuji 16mm f/1.4 - amzn.to/31RbbRH
Microphone: Rode Video Micro - amzn.to/31SIeER
Recorder: Ninja V - amzn.to/31Y8qxM
======================================
â¶ïž Frankâs CZcams PlayList
======================================
Yaesu VX-6 - tinyurl.com/yaesuradiovx6
Baofeng UV-5R - tinyurl.com/baofengradiouv5r
Yaesu FT-991A - tinyurl.com/yaeuft991a
Yaesu FT3D - tinyurl.com/yaesuft3d
Fuji X-T3 - tinyurl.com/fujixt3
Fuji X-T2 - tinyurl.com/fujifilmxt2
Fuji X100F - tinyurl.com/fujix100f
Fuji X-E3 - tinyurl.com/fujifilmx3
Fuji X-H1 - tinyurl.com/fujixh1
Fuji X100V - tinyurl.com/fujix100v
=============================
đAffiliate Links:
=============================
Some of the links in my video descriptions are affiliate links, which means at no extra cost to you, I will make a small commission if you click them and make a qualifying purchase. If you have a different purchase in mind, you can also use these storewide links below.
PLEASE SUBSCRIBE: tinyurl.com/frankromero-sub â
â â â â â â â â â â â â â â â â â â â â â â â â â â
Nice video. Straight to the point and no goofy stuff. Thank you
Well done! Yes your instructions work for Windows 10.
Excellent instructions mate.
Thanks, great Video đđ
I use my 857D with wsjt-x and fldigi via digital VOX and a Signalink. I could never get the rig to communicate properly or consistently with the computer (Win 10 laptop) to enable rig control. So one day I tried solely digital VOX and it worked fine, but without rig control. For me, this is not a deal killer, so VOX it is. Take care, have fun, stay safe. 73 de Cliff W3KKO
Thanks for the video!
No problem. -73
Would you do a review on rx on HF comparision between 891 and 857D (I assume D).
Nice vide though that last segment losing the right channel made me think that I broke another headset :D
Thatâs happen to me.
I've Ft857. on Ft8/DGI mode with CAT if I set power more than 10 watts was errors, I mean the frequency inconsequential or move on another band uncontrollable. How about you? YD2CQE
@@frankwc0o oke thank you for your response, I use CAT U5 link for Ft857, asus ROG installed run on Windows 10 & both wsjt-x, JTDX sound card. If you want, I can show you the problem video
@@arafebi5414 Had very similar problem with Ft-857 running on old G73Jw Asus. I put ferrite beads over all of the USB cables, and the audio interconnect cables connected to Asus, and it fixed it. I think the asus was just too sensitive to RFI. The notebook lacks any good RF shielding, and there are very few ways to provide sufficient grounding. It took a bunch of ferrite beads on each cable.
Hi Frank, could you recommend the computer settings you use please? 73's Dave G6EGM
Yes computer setting, please Brad KH6OWT
IF you use the AT897+ tuner, the baud rate can only be 4800.
I noticed something odd with FT8 on my 857d. When setting the transmit frequency in WSJT-X, the rig center frequency seems to be interpreted as the center of the SSB passband rather than the carrier frequency. Is that your experience as well?
@frank wc0o - some sources claim that you should only use CAT rate 4800 bps with Yaesu857 when setting up menu #19 for use of digi modes. You recommended 38400 bps, do you feel that it works just fine, have you tested the lower 4800 bps?
I have never tried 4800 bps. You should try 4800 and if your results all good then you should keep it that way. Itâs possible that other equipment could not go any higher than 4800 when this radio was first introduced . If you do decide to use 4800 come back and tell us if you liked it.
@@frankwc0o Thank you for your swift reply! I am happy to confirm that the 38400 bps setting works very well w/ the Yaesu 857D and FT8. My earlier problems were caused simply by a bad connection in those !%##"! mini DIN connectors on the Yaesu rig, got them modified and sorted today. Thank you for your excellent instructions, got the Yaesu a new job as my parks/44 rig now! 73 de OH2CJI
@@jans4636 Super. Ya, I had a bent pin and there goes $20! I'm glad we have better tech today. Although, I wish the would make a new version of the 857D.
4800 works fine with my 897 for all the digital modes I've tried. I had to do this rate as the port is shared with an AT897+ which runs at 4800.
Is that a radio or a model of the Millennium Falcon? (For all you kids under 50, I am referring to a Star Wars movie spacecraft.)
On one hand people tell me the FT-857D won't do Digital without a soundcard, on the other hand Rig Blaster Tech support said I didn't need their interface.
Itâs true you need some type of interface so the computer can talk to the radio. You should look into digirig very easy to use. Check it out
Upgraded-LONCEVON 10 inch Small Mini HDMI Monitor with VGA USB BNC AV Port;Mini LCD Screen 12V Monitor for Raspberry PI/Camera/TV/PC/Car Screens for kids;1024x600 Pixel with Speaker Remote,Cigar LightUpgraded-LONCEVON 10 inch Small Mini HDMI MâŠ
$68.99
Mini PC Windows 11 Pro GK41 Mini Desktop Computers 8GB DDR4 128GB SSD Intel Celeron J4125 Processor Dual LAN Mini PC, Digital Mic, Business Small PC 4K HDMI/DisplayPort HTPC, Dual Band Wi-Fi Micro PCMini PC Windows 11 Pro GK41 Mini Desktop ComâŠ
$159.99$159.99
& FREE Returns
In Stock
Size: GK41-
@@frankwc0o
Upgrade] 1Mii USB Sound Card USB to 3.5mm Jack Audio Adapter - Virtual 7.1 Surround Sound - USB Adapter for PS4/PC/MAC/Stereo Headsets, External Sound Card No Drivers Needed Plug and Play
Did you write software for Raspberry Pi or download it?
All the software can be downloaded to the Raspberry Pi. All you need to do, what I did, was to configure the files to start up correctly.
Where did you get it? Jason, KM4ACK?
@@frankwc0o Also, does it interfere with normal VHF, HF activities?
@@lblittle1207 no. Just found it on the web.
@@lblittle1207 do you mean - do you use the same frequencies? Yes.
I can receive but I cannot transmit radio transmission code
I'm trying to transmit on about Bang radio I can receive the frequency but I cannot transmit on the frequency I don't know the code it I can't find it
Same for me could receive, the tx is on in the radio red light but the doesn't strong enough.
@@frankwc0o tks
I have the same problem. I can RX, but when I try to TX, radio red light comes on, but power meter shows nothing being transmitted, and PTT LED on SignaLink stays dark. BTW, my setup as-is works fine with Fldigi, but not with WSJT-X. Help!
@@davidboyd1395 I have the same issue with WSJTX and the Digirig mobile. I don't know what to do RX is great , TX red light is on no power out. If you figure out a fix please post it.
Would you do a review on rx on HF comparision between 891 and 857D (I assume D).