Well done mate ,best g9u build out there ,awesome footage of them dam gears ⚙️. That’s explain a lot ,mines noisy in that area,so I’m guessing I need a bmx crank and some flat sheet also 👍 to fit some New gears Cheers mate Thanks 👍
Great videos👍 First 3 questions: are you satisfied with your newly built engine in your van/camper and is it still running❓ Which parts did you use, all original or after auten/original equipment manufacturer quality ❓ What did it cost from the parts alone ❓ I just bought an 2003 Nissan Interstar 120dci with g9u 720 with 178000km ,4 weeks ago.Only injectors should be new/cleaned because it's working again (he starts badly, and takes on gas with difficulty, when he runs it soots so rough from the exhaust pipe).. unfortunately no injector problem 1000 € away 🤦.. because compression was tested first and 1&2 cyl only 8 bar, 3&4 17 bar. .fuck-I have engine damage😒..I hope that I will only need new piston rings,seals and so on and that I don't have a cracked cylinder head.✊✊ Seller doesn't know anything, as always 😒 .... so I searched the net for days for videos, data etc .... until I saw your videos. Awesome, thanks, that has now brought me to overhaul the engine myself (it's my first diesel engine, I've already disassembled and rebuilt a few petrol engines). Thanks to your video, I was afraid that it can't be that bad. THANK YOU.✌️👍
Yes I found an online service & rebuild manual to refrance throughout the process. Would always recommend reading through the process before beginning to be sure your prepared and will have everything to hand that you're going to need.
Well done mate ,best g9u build out there ,awesome footage of them dam gears ⚙️.
That’s explain a lot ,mines noisy in that area,so I’m guessing I need a bmx crank and some flat sheet also 👍 to fit some
New gears
Cheers mate
Thanks 👍
Again awesome!! Is there a part 3 on the way?
Great videos👍 First 3 questions: are you satisfied with your newly built engine in your van/camper and is it still running❓
Which parts did you use, all original or after auten/original equipment manufacturer quality ❓ What did it cost from the parts alone ❓ I just bought an 2003 Nissan Interstar 120dci with g9u 720 with 178000km ,4 weeks ago.Only injectors should be new/cleaned because it's working again (he starts badly, and takes on gas with difficulty, when he runs it soots so rough from the exhaust pipe).. unfortunately no injector problem 1000 € away 🤦.. because compression was tested first and 1&2 cyl only 8 bar, 3&4 17 bar. .fuck-I have engine damage😒..I hope that I will only need new piston rings,seals and so on and that I don't have a cracked cylinder head.✊✊
Seller doesn't know anything, as always 😒 .... so I searched the net for days for videos, data etc .... until I saw your videos.
Awesome, thanks, that has now brought me to overhaul the engine myself (it's my first diesel engine, I've already disassembled and rebuilt a few petrol engines). Thanks to your video, I was afraid that it can't be that bad. THANK YOU.✌️👍
Hey can u give me please an answhere wad i have ca~ to spend in my build,or wad did u paid? Thx
hi buddy can i ask you where you got the crankcase seal and the seal above that from as im stuggling to get them cheers
I believe I sourced them through e bay I'll have a dig through my previous orders for you and if I can find a link I'll share it your way
at these double gear, isnt there a whole ? i saw a guy using a conic headed screw to get the gears match
hi buddy are the bottom crank bolts the same as the head bolts and have you got a link to where you got them from
Hey Buddy! Thanks for your videos !! Iam stuck in overhauling the same engine.. took mostly everything apart..
did you use oversized piston rings?
No , I only had my cylinder bores honed and reinstalled new stock size rings as the measurements were within acceptable working tolerance.
🥳
And is there an shop manual for all details? I am so afraid of making small mistakes with big effects 💩😍😊
Yes I found an online service & rebuild manual to refrance throughout the process. Would always recommend reading through the process before beginning to be sure your prepared and will have everything to hand that you're going to need.
@@Adventure_Van_Upgrades oh brilliant! Do you have a link? I only found a not really detailed one :(
Did the hard water pipe at the back have o rings on the pipe when push into the water pump?
Yes , I installed new o rings , I believe they were included in head the gasket kit
hi you had the bloch homed did you use te same size rings or did you get bigger ones not sure how it works
Cylinder bores were only lightly re-honed , not re-bored so it still takes a standard size set of rings 🙂
@@Adventure_Van_Upgrades cheers
Them new piston rings was the top ring 2.5mm or 3mm?
I couldn't tell you from memory, sorry.
I'm pretty sure they were bought as a kit and not individually
What did you torque the rod bolts to.
I had found a online workshop manual to follow for all required specification.
Ist overhaulporn
Thx
How was the crank bent 😮
Running the engine with a disintegrated big end bearing had warped the crank slightly
When you took the conrods of did it still spin over freely
Please support the channel back and forth.. I look forward to accompanying you..