Adapting 3M Adflo Speedglass PAPR to use DeWalt Drill Battery with CASE Why You Need a PAPR
Vložit
- čas přidán 27. 07. 2024
- Original idea:
• Can a speedglass adflo...
Info about low voltage cutoff board:
• Low voltage cutoff pro...
CAD files for 3D printed Case on grabcad.com:
grabcad.com/library/3m-adflo-...
*Links for parts may go bad as sellers change.
Low voltage cutoff board:
a.co/d/gjhP9fV
Voltage step down board:
www.ebay.com/itm/325041823422...
Dewalt power bank:
www.ebay.com/itm/125056370446... - Zábava
awsome man ! thank u so much 👍👍👍
Just found everything I need on Amazon and I just purchased a 3D printer for Christmas so this is perfect. Thanks for the informative video. It blows my mind that the battery cost $600 to replace. Cheers from Canada.
how have i never thought of putting a light on my helmet ...im so angry. you got a like from me :D
One back up battery for these is around $500. Great idea! Thanks for vid.
Very good and informative video. I have the 9100fx and g5-01 and personally prefer how secure the 9100fx stays on compared to the g5. Not a big deal if you’re working in a shop but is extremely aggravating working 10 hour days and have to constantly move and fit into tough spaces.
It’s a great idea using dewalt batteries instead of the overpriced 3m batteries and will someday implement it into my blower. Easier and cheaper to buy and charge multiple batteries and use with my other tools. I’ve rebuilt a couple of my 3m batteries but if my chargers start to die on me I’m doing the switch.
I use to use the quick release half face but over time has left a dark spot and even widened the pores on the bridge of my nose and even occasionally cause pain from tenderness. Never go back to that again.
Thanks for the video and keep up the good work.
Thanks! Sorry the half face is so uncomfortable over time! I try to avoid it by just saving it for tight spots too. Good luck with whatever you decide to do in the future!
Great informative video! Especially on the Adflo/Versaflo unit!
great video. Mine is shutting off at 14.4 with a low battery signal. may need to change the voltage converter
Thanks! Make sure that that is 14.4 V under full load - have the filters on and the hose and helmet hooked up. If it shows 14.4 V under no-load, the voltage will drop a little when the load is applied.
If that doesn't work, maybe try 14.5V or maybe your DRO is bad on the board and you can test the voltage with a multimeter
Nice video:), im planning to make the same setup. I still have the (broken) original battery and it says 10.8V, and u have it on 14.4V. Is it working fine on 14.4V, just wondering then im gonna make it like that aswell.
I believe these came in 10.8 and 14.4 V battery configurations depending on what year it was made. I would try 10.8 first and if you get the low battery voltage beeping alarm, then try 14.4.
Hey I got a Coleman ct200u minibike and I was wondering if you could do a video explaining how to take off the gas tank for me
I don't have a stock setup anymore, but this video does a nice job: czcams.com/video/oh8zhS-h1v0/video.html
Did you get a fix for it running for 15 seconds or so and shutting off?
If you haven't already, Make sure that that is 14.4 V under full load - have the filters on and the hose and helmet hooked up. If it shows 14.4 V under no-load, the voltage will drop a little when the load is applied. If that doesn't work, maybe try 14.5V or maybe your DRO is bad on the board and you can test the voltage with a multimeter. Lmk if that works