BTT Octopus V1.1 - TFT35 V3 display configuration
Vložit
- čas přidán 16. 07. 2021
- This is a brief tutorial on how to configure TFT35 v3.0 on Marlin Firmware version 2.0.9.1 with BTT Octopus v1.1.
BTT Octopus v1.1 playlist link:
• BTT Octopus Tutorials
One Time Tips, You Can PayPal Me:
www.paypal.me/EBraiman
Patreon:
/ edbraiman
buymeacoffee:
www.buymeacoffee.com/ebraiman
Discord Chat:
/ discord
Required hardware:
BTT Octopus V1.1
BTT TFT32 v3.0
BTT TMC2130 SPI
BTT TFT35 v3.0
NEMA 17 motor
USB Cable
SD Memory Cards Class 10
Required software:
Documentation and Firmware
github.com/bigtreetech/BIGTRE...
Software:
Marlin Firmware 2.0.x
marlinfw.org/meta/download/
Installing VScode:
• Installing VSCode with...
Pronterface:
www.pronterface.com/
#Octopusdiyshow - Věda a technologie
Thanks a mil man - for all of your (octopus) videos! Super Helpful!
You're welcome.
Thanks for the video! It helped me get my TFT70 working with my Octopus 1.1
One note: you can get rid of one of the ribbon cables by choosing CR10_STOCKDISPLAY instead of REPRAP_DISCOUNT_SMART_CONTROLLER, then connecting the EXP_1 port of the Octopus to EXP_3 on the TFT. It has the exact same functionality, but less cable clutter :)
You're welcome.
Great video as always, but you might want to change the title and description to TFT35 from TFT32. Just helps with searches.
Keep the videos coming :)
Thanks.
All fixed, TY.
Works with Octopus 1.1 and TFT35 E3 V3 (video shows the previous version V2 I think, as the encoder knob in the video is to the right of the screen. the V3 has the encoder knob on the bottom just like an Ender 3 pro screen
Thanks.
TFT35-E3 V3 has the encoder bottom and TFT35 V3 has to the right
@@vincestruhar correct. also he did not show show where to hook up the tft cable...
Thanks
You're welcome.
I was curious if I have to change anything in configuration.h or configurationadv.h? Got an ender 3v2 with tft35v3.0 and it’s the last part of my compile. I’m assuming it’s not just plug and play? Boards a octopus pro v1.0 with 429 chip. Thanks
Depends on what you wish to configure. It can go off in hundreds of directions. TFT has a configuration file as well as Marlin firmware.
Like it? I love the tutorial. Still working on the whole "no printer attached" debacle, but in doing so I uncovered a hidden drinking game: Down a shot whenever he says "actual" or "actually". ;-)
No printer attached is usually buad rate on display.
@@EdwardBraiman Tried all of them at this point, still no printer attached. When I want to restart the firmware to try if it would run it writes "mcu 'mcu': Command format mismatch: config is_config=%c crc=%u is_shutdown=%c move_count=%hu vs config is_config=%c crc=%u move_count=%hu is_shutdown=%c" That probably refers in some way to all the things it just had me delete one by one, while promising it will start to run if I do...
Try my Discord in description below.
hello i have done the same as you but can't get the screen to turn on if the third cable is conected.
the black cable
Can you post a picture of your connection on Discord in link below.
Is btt mini lcd 12864 v1 display compatible with octopus pro...!?
For some reason, I can't get this to work with the Octopus Pro V1.0 with TFT35-E3 V3.0.1. It connected with the FW as supplied the first time I turned it on, but after going thru the TMC2209 and this tutorial, I can't get the TFT to connect. Pronterface connects, though, so I can verify the drive update happened. Other than the cables landing in a different spot, is there something else needed for the Pro?
There's a Discord link in description. In General chat either myself or someone else can walk you through it.
My Fault! Copied to wrong environment declaration. Thanks for these vids!
I have a problem to connect my display with the BTT Octopus V1.1 to my display. I use the TouchScreen von BTT (TFT70). What must i do to connect them?
Not sure I understand your question. Are you referring to another type of display made by BTT?
@@EdwardBraiman Correctly! But I've already solved the problem. I did not set a jumper correctly on the Octopus and therefore the processor was not flashed. Now the only problem I have is that the motors are not working properly.
There's a tutorial playlist in description. If you cannot see it in chrome browser look in Firefox browser.
On one of your video you mention a power supply set up which video is that on please
All my videos talk about power supply in one way or another. As for wiring power supply for PSU for use I avoid subject because US standards are not the same for everyone. For example I was told by a user in Egypt they don't use ground. So I avoid subject. My preference is US electrical standards.
@@EdwardBraiman I live in Colorado and I want to set up my board like you are before putting it together but I understand
@@tzpetlover Join my Discord below in description and I'll see we can walk thru the issue of wiring.
@@EdwardBraiman Thanks
You're welcome.
would this also apply for the tft35 e3 v3.0?
Yes.
@@EdwardBraiman wrong. it does not have a tft connection unless it is labeled something else
@@victorhugo-nt8yh That's the RS232 connection
Any Servo options?
Servo option is part of BLtouch.
@@EdwardBraiman Yes BUT ONLY ONE servo go back the RAMPS for more
Ramps or MkS Gen L v1.0. although it's possible to add more on newer configurations with some modifications to Marlin firmware.
@@EdwardBraiman More servo's a how to needed please BBT SKR 1.4, without OctoPrint using Pi
I'm working my way down the lists of requests. I'm behind in tutorial requests due to the hot weather here . That one is going to be a challenge to do. Today I spent over four hours just record a Klipper tutorial.