Video není dostupné.
Omlouváme se.
how to build a forged 800whp+ VQ37VHR (part 2)
Komentáře • 12
Další v pořadí
Automatické přehrávání
How to build a forged 800whp+ VQ37VHR (part 3)Seth Joyner
zhlédnutí 1K
VQ35HR vs VQ37VHR: Which One is Better?Dust Runners Automotive Journal
zhlédnutí 80K
Twin Turbo 350z - 700+HP (Hopefully) Time Lapse BuildGymkhanada
zhlédnutí 3,8K
This is the Biggest SAW in the World 😱🪚 #camping #survival #bushcraft #outdoors #lifehackMarusya Outdoors
zhlédnutí 18M
Wavy or Curly? #hairstyle #hairtok #hairhack #hairtutorial #hair #easyhairstyle #beautifulcurlsAlina Shmidt
zhlédnutí 23M
UZDRAVME SRDCE ELIŠKYRaegoTV
zhlédnutí 132K
Ne jamais regarder une fille à la plage 😂Nicocapone
zhlédnutí 7M
How To Rebuild A Car Engine (4G63)Devin Niemela
zhlédnutí 463K
Nissan 350Z fitting timing chain.Stuart Husband
zhlédnutí 33K
Building a Forged VQ37 - Rotating AssemblyAdam LZ
zhlédnutí 313K
How to build a forged 800whp+ VQ37VHR (part 1) #nissan370znismoSeth Joyner
zhlédnutí 4K
Boost Control Explained [GO FAST BRETT]MCM TV2
zhlédnutí 923K
Porting cylinder heads to optimize engine performance | Hagerty DIYHagerty
zhlédnutí 1,3M
Full Build: From Rusted Out 1961 Chevy Impala to Revved Up Red SledPOWERNATION
zhlédnutí 1,4M
This Is Why eBay Turbo Manifolds Are GarbageKenny McKee
zhlédnutí 137K
How to build an 1100 whp VQSOHOMotorsports
zhlédnutí 46K
艾莎撒娇得到王子的原谅#艾莎在逃的公主
zhlédnutí 44M
Udělal jsem si HWACHAE (špatnej nápad)MaTTem
zhlédnutí 122K
ОБЯЗАТЕЛЬНО СОВЕРШАЙТЕ ДОБРО!❤❤❤Chapitosiki
zhlédnutí 27M
How Hard Is To Slice With The World's Smallest Sword?Mini Katana
zhlédnutí 40M
Ajka hodila pořádnou hubu! 😁❤️ AirTrack klouzání na Tary Campu!Tary
zhlédnutí 325K
How Countries eat spaghettiLionfield
zhlédnutí 13M
Eleftherios Petrounias helped by Arthur Zanetti = epic gala moment ❤️Olympics
zhlédnutí 47M
Který kostým je váš nejoblíbenější? 😭Natyla
zhlédnutí 127K
Okay question! Just picked up a 370Z with 72k miles 2009’for 9000 cash off this Guy, but I wanna do a N/A build with running forged components..
I wanted to
Do eagle rods an wis pistons… can you help me in the right direction..
What would be a good direction with this.
I know N/A won’t be much power gains but it’s still a cheap route than boosting for now..
Figured I running forged would save a few problems in the long run internally
@_Zoctane u can definitely run like 600-620whp stock internals all day with a solid tune...seen cars last for years like that..still healthy..just a thought...but minimum is what u stated..eagles will hold just fine...probably unnecessary unless ur pulling over 650whp
Man love the video lots to think about! One question tho what compression ratio do you suggest. Thinking bout the z1 supercharger kit.lots of people are apparently running 500 with stock internals without problems. while it is the goal power wise,it’s also a goal to build it as reliably as possible
If you're only planning on 500@tire (which is by no means "slow") I would totally go down the supercharger rabbit hole...a stock VQ maintained properly can support that power level for years without a hiccup. Twin turbos is a highly involved (motor drop) and laborious installation. The supercharger and fuel system could be casually installed in 2 days...annnd...blower cars are fun to drive🙃
@@sethjoyner391so the engine is torn apart right now I should just keep the stock pistons and rods then?
@bassel000x soooo..it's all about power goals....5-600hp and it was a clean tear down...je pistons and eagle/bc rods, something basic..don't forget upgraded gallery gaskets/hardware/ 271 lock tight...I also suggest an ati dampner for all engines especially if cammed/ forged etc
Hey what state are you in
I would like to know also
How required is it to run this wire for good headseal?
IMO with proper cooling...anything over around that 800whp mark...regular solid deck mod w/no o ring; probably 750whp all day
@@sethjoyner391 I appreciate your response man. These videos are super helpful
@jad007cafe7 thank u man..appreciate u watching my stuff!