I get the thought process. He always tries to make sure that the covert entry won't be detected. Although in this case, you're absolutely right. I'm pretty sure they would notice their lock being scorched and broken...
The fact that they actually asked for feedback and made alterations on future products based on said feedback from the locksport community is highly encouraging to hear.
IDK, if there's potential for a lock body to just wash away under a few minutes of heat from a portable torch that doesn't really raise any suspicion to carry in your truck, that seems like a practical way to take someone's stuff in the right circumstances. Good to see that this lock isn't that way.
@@MushVPeets the key phrase is "a few minutes." You would have to stay there in one position with a lit torch going ham on the entrance to somewhere without anyone actually going by and noticing you. In the world we live in people are everywhere, and more time is more of a multiplier for getting caught. If you are not in a situation where you are out in the open, you had to 1:park in a weird spot. 2: drag that torch out in the open 3: walk a suspicious route while carrying a fucking blow torch, THEN stand there and go ham on the lock. It really is weird and impractical.
@@onlinepanic2036 Put on a tool belt, a yellow hard hat and overalls, wave at people as they pass by. You don't have to hide, you just have to look like you're hired to be there.
@Charles Wetherspoon Unless I misremember the Turkish Police (as I remember it) did a test (due to having a large amount of kidnappings from the homes) were they (in civilian clothing) just went to the front door, knocked and asked the person opening to take a sip from a glass of water they were holding in their hand, apparently a l disturbing amount of people actually did it.
Consider that you're now at a level when you're picking open a lock in under 2 minutes, you state "Quite a bit of fight out of this lock." Heheheh. Great job, man!
@@lockpickinglawyer I wasn't watching the clock and it seemed like longer, but that must be because you're so quick with everything else. I was a bit disappointed when you cut away for putting it back together. Do any of your videos show the reassembly after you gut a core? That's something I'd like to see.
Melting point of aluminum is approximately 200 C higher than that of zinc. Closer to 250, actually. It’s possible he was thinking Fahrenheit but accidentally stumbled upon the correct interval in Celsius. Or he was correct all along and was using an untypical unit of measurement for those from the States.
Scientific fields use metric measurements, even in the US, so he very well may have been using metric. It's so much simpler when you start to get to the extremes of temps.
Aluminum gets brittle as it heats up. In welding it is called "Hot Short" I believe Paclock simply used a standard extruded aluminum like heat treatable 6061 and machined it down. This differs from the metal in the American lock in that it was CAST, not machined. Casting aluminum is not the same as extruded aluminum (like the Paclock) It is chock full of doping agents (zinc can be one of these agents along with a host of other things). This can, not so much change the melting point (which it DOES, but not by as much as you may think), but aid the casting type aluminum in melting and freezing (changing phases) more uniformly, and so the American gave way all at once, whereas the Paclock would reach melting point at different points throughout the torching, but it's chemistry is less condusive to uniform "liquidus" and conducts heat better, being more "pure" aluminum than the casting aluminum and so made it a fantastic heat-sink. The back of the American seemed to fall out, though it is uniformly shaped. Generally, aluminum likes to be the same temperature ALL the way around and as fast as possible. Just an observation that ultimately means nothing. Here is a link to an article describing hot-shortness www.corrosionpedia.com/definition/638/hot-shortness
Also helps a bit that he's got it in that nice big metal vice. Think this is a situation where having it on the chain would actually be a benefit because the air and chain links are a much worse heat conductor in their own right.
@@erikev He's not saying that its directly brittle when hot. He's saying that the more times you heat it up, the more brittle it becomes (more aluminum oxide in the structure).
Quick note: I wouldn't classify a blowtorch as a "plumber's torch" as you did in this video. It's much more useful (and the trade standard as far as I know) to refer to them by the fuel used: propane torch (hot), MAPP gas (really hot), etc. They often use the same torch head and connectors, but the difference in fuel distinguishes their use as propane will melt solder for copper pipe; MAPP gas will also melt solder but it's too hot for small pipe. Acetylene is hot enough to cut pipe. Cheers
When your everyday real people CZcamsrs actually prompt entire companies into rethinking, researching, and ultimately improving a product for everyone... That's what's up.
@@mattmurphy7030 i have doubts about masterlock lol. also, a year ago, when i posted this comment, LPL wasn't quite as well known of as he is today. Deservingly too!
Defcon has some, and other locksport events go down all over the place. Some that immediately comes to mind is the locksport club in Austin, Texas or Seattle, Washington. Most major cities have one or two, Google it. The benefits of these types of events go from designing elaborate puzzle locks for fun, testing locksmith's skills, and improving on manufacturers designs. More than a few (reputable) manufacturers have upped their game and recalled certain locks with glaring flaws. And for the ones insinuating that locksport enthusiasts are criminals in training, that's such a simple minded point of view. That's like saying everyone who learns martial arts or trains to run fast or be an impressive marksman/markswoman or learn cyber security pen/testing are also all trying to learn to be criminals. Edit: got more specific about locations and how to find events/clubs
At last a lock company ceo that listens to and puts into practice reviews by LPL and BB, AND reads the comments. Basically he has the smarts to save a huge amount of expensive R&D.
Hi LPL, I just wanted to chime in here. As I am actually a Plumber by trade and a Lock sport enthusiast by hobby, I should tell you that your torching technique would have been quicker had you set your flame at the correct distance from the work. The hottest part of any flame is at it's tip. I noticed you being too close and I would have recommended concentrating the flame more to the outer side of the lock body opposite of the pins. Otherwise the mention of a steel version was ideal. I made that suggestion in the comments in Bill's video review as well. Great review! Thank you!
@@bytheseaaspirinshop801 I agree even though only a small part of the lock was in contact with the vise it was very close to the spot he was heating and allowed a lot of the heat to sink into the vise.
J. Wilson additionally it appeared as though care was taken to focus the heat on the shackle and to avoid heating the aluminum at the weakest point and advance the molten puddle towards the locking components. It's almost as if the LPL didn't want the heating attack to be successful. Then you see the glowing review of the review of the lock by the Manufacturer, and it's enough to make you go hmmm.
Jon Hunt I was thinking the same thing while watching, I normally love his unbiased videos but this one seemed off to me as he is focusing the heat to the only parts not made of aluminum
You said... "The hottest part of any flame is at it's tip.", I wanted to add a reference... www.bernzomatic.com/Using-a-Torch/Torch-Safety (search the page for the word 'hottest').
Another thing. If it were mounted on metal, heat dissipation would be greater. If on flammable material, you'd burn the house down before melting the lock.
Only recently found this channel and I’m noticing something incredible. Unless I’m mistaken it seems that companies making new locks are in touch with and seek feedback from the lock picking community. That’s genuinely amazing.
@@mrevilducky **lockpicking. trying to rebrand this hobby is outright pointless and ignorant. theres nothing wrong with having lockpicking be your hobby.
Hey, we know yoi like picking locks, so made a custom lock for you! We made it your favorite color, and engraved your name on it, isn't that neat... also, we need you to destroy it.
Considering one of these to lock my bike. They're relatively affordable for the security level, and throw in a good solid self-looping security chain and we've got something that can rival solutions that cost more, but are less effective.
It's amazing how much harder these locks are to pick in thier used environment, especially when they are ridgid, butted against the locked item. Making the lock picker contort into gymnastic positions, and leave no room for grasping, and turning tools, and even for knuckles of the hands in a grasping mode, changes the security rating.
Spot on! We always start aluminum to test the market and then move to hardened steel if the concept looks good. We're going to keep the aluminum body as an option mostly because of the weight savings... for bicycles and motorcycles where carrying a 1lb lock that's pretty darn good versus a 4lb lock that's super strong (but kills your back!) is a good option.
@@paclockpres.9805 I know this is an old video and post but this right here not only shows that PacLock listens to the Lock picking community but also reads the comments of the videos. That, to me, is just as impressive as their locks. I just started on this journey and hope to achieve the 200k Club.
@@dechert3602 Thank you! We'll be having yet another prototype posted onto our CZcams account within the next few days for comments and testers! And good luck with your 200K Club admissions!!!!
haha I like how the company colored the lock with diecast blue (which gives off toxic fumes at high temperatures) and then they were like “here you go, by the way do you think you could melt it?” Trying to murder the LPLawyer so he can’t defeat any more of their locks, nicee that’s mad smart
Cool! I found these in a search a while back and lo and behold BosnianBill and LPL not only review them but PacLock improves them accordingly. Awesome! Yay PacLock and LPL!
Merlin Same here. LPL and BosnianBill really opened my eyes to how vulnerable some lock brands are. After seeing how receptive Paclock has been to suggestions and security I ordered a couple from HD. They will be used for protection and of course... play 😎
I think there was another negative before that: 19:23 "This isn't a lock I wouldn't hesitate to use". Probably meant to say what you wrote, but it threw me a bit when I heard it.
Your videos have the absolute best commentary while you are picking the lock. That is the most valuable part for those of us who are trying to improve our skills. Also, your camera is in focus! Bill's videos drive me nuts with his constantly blurry close-ups. Looks like this lock is a good training lock for pickers. Thank you for another great video.
Calm and methodically laid out description, pedagogical and thorough, I like that. Only one thing worries me and that is that "wrong" people who follow you, learn very useful for them. But the rest of us learn what to observe. It's great Thanks for a very good page. Carsten Sweden
The essential difference between the liquid-melted lock body and that of this lock is that an aluminum wrought alloy was used here, as used for the production of extruded semi-finished products. Here the practically melted material at the outlet of the nozzle must have sufficient strength to hold the desired shape. A cast aluminum, on the other hand, has to melt thinly in order to fill even fine structures in a mold. So much for my knowledge of materials science from studying mechanical engineering.
Pack lock Blue one can be super secure with a hardened cup cover bolted from inside door with 1 large hardened bolt. Also that anti hacksaw pin should be hardened and looose so it rolls with hacksaw blade
Your attention to detail and the practice of routine is incredible. You know full well you're about to completely destroy the lock with a torch and make it totally unusable. But you still protect the bottom of the lock from damage dissed by the pick anyway.
I like the design that it can be bolted to a surface, and if made from steel and toughened as stated would be a great lock to buy if available in the UK
It's amazing how much I enjoy this. I think you cadence and tone as well as knowledge make the pace that sweet spot for information assimilation & entertainment. I'm a big time nerd, so this is my jam. I specialize in ballroom dance history, but we're cut from the same mold of wanting to endlessly learn. This might be our intellectual interface. Thank you, you are my nerdy ASMR.
That American lock looks like it might be cast aluminum. In my experience, cast aluminum is more brittle than it’s barstock counterpart. Given that the PacLock looks milled, I wouldn’t be surprised if it was made of a pretty tough grade aluminum. I wonder tho if you could’ve gotten it open faster by heating further toward the elbow and then prying with some channel locks or vice grips to get better leverage over the needle noses. Very cool stuff +1
Nice review. I like your objective approach to this. I don't know if that's the right word but you and Bill both do a great job at quality info / time ratio. Thank you. Portland, ME
Awesome video. I also hate to see a good lock destroyed, but I believe its ok in the matter of science and learning. This is how we all learn to improve things. I'm proud of PacLock for actually listening to the end user. Thank you for sharing this. Also, great picking LPL always a pleasure to watch you work the pins.
I'm absolutely hooked on the channel, LPL is amazing, the skill and knowledge he has is freaking great. I don't even have anything padlocked, but I now know if I do there's plenty I don't buy!
Being made out of aluminum my biggest concern out of those you addressed would be a prying attack. Using a pry bar and leveraging off of the hasp or chain and prying the top you would think it would bend or outright break quite easily. There isn't much material on the bottom of those steel pins that hold the shackle, and even with a thick steel pin inserted into the "neck" of the lock it should still bend quite easily. The sharp corners inside the mouth could also be a weak point. Having them rounded would increase strength.
The only way I see practical to damage this lock by leverage attacks would be mitigated if not completely eliminated by that steel rod, unless this is locked to a solid steel door or some other surface hard enough where you could bend the entire lock without damaging the surface that's mounted to. Any lock not made of solid steel is going to be a low security affair so we're talking stuff like fence gates, sheds maybe get a cheap chain and secure your relatively cheap bike to it or similar. Situations where the lock is secure enough that if the thief wants the stuff they're likely just going to take the easy route of say destroying the chain or getting a sledgehammer and just busting through the shed walls or whatever
I totally agree with the steel lock body. Even though PacLock installed steel rods in the new design, aluminum is very soft and can be manipulated. A steel lock body would be more expensive but that point is moot if you are securing something valuable. Great video!!
you are able to talk very clearly and it seems like you think about every word that comes out of your mouth before you say it. which makes you very easy to under stand.very well spoken and the best locker picker iv'e ever seen.its crazy how easly you bypass some of those, incredable
Great video brother. I agree with your observations, this lock definitely dispersed the heat better than the 1100 preventing it from getting hot enough to melt aluminum under those pins in the same way as the other lock. Thanks for the review!
I suppose, if you were bolting it to a surface, you could include a 2-3 mm plate of very hardened steel on the outside face to gain a lot of protection with only a little material.
Hey there @LockPickingLawyer , awesome video! It was entertaining and I enjoy how you describe as you go. That is very helpful to me, as an in-training locksmith, to watch your hands work, where you're at within the pick and the action happening. I think you're great at what you do and your videos are awesome. I'm pretty familiar in the destructive opening techniques and have background on construction, structures and support and if I may just share my opinion. If the idea of the video was more for presentation during the destruction, then the already unlikely of ability to destroy this lock in this manner, then that's no problem. I guess what I mean is that in order to properly make an attempt such as this or similar "attack openings" would be to do in in real world situations. My example would be like if you were really trying to get whatever this lock was supposed to be protecting, perhaps the time it would realistically take to get into any lock, just out in the world, plus the determination and tools of the potential thief. By about 2.5 minutes into the demonstration, I think that the red-hot steel could possibly have been pried and essentially reshaped it's locking ability into the block of also steel pins, it could have popped, potentially. Personally, having the mostly common knowledge of hottest burning portable torch and gas setups, I think the yellow map gas can, from an above angle and the position of the torches flame, I think the lock might have opened in a fraction of the time. Of course I'm not intending to insult your work, but coming from my knowledge and background, desperation can make any lock openable. I think that if the company of the lock was relatively confident in its core's ability to seem the biggest hassle, they should look to have a real-world torture test done, perhaps also as a review. With that said, I really enjoy your work and I hope that we continue to improve our ability to protect ourselves and thanks to people like you and @Bosnianbill ,we might just get there one day. Thank you!
I’ve been a “machinist/toolmaker/ mold maker” for well over a decade. I have extensive experience with a multitude of materials. When I hear “it made of steel!”... many questions come to mind. To me steel is butter. What kind of steel? What’s the Rockwell? Yield strength? Why are we still using steel for locks? Is it a cost issue?
Steel is relatively easy to shape with the right tools, what else would you make locks out of though? Materials like tungsten or cobalt alloys are too brittle or too expensive, basic titanium is easier to cut than steel aside from the binding issues, and most everything else would be worse in all categories. The only thing I think would be better is properly heat treated beta-ti or 6alv4. At that point, a high toughness tool steel with a proper heat treat is still going to be better though, and cheaper as well. To excuse anything I'm missing though, most of my experience comes from bladesmithing and not from a general material science standpoint.
The craziest thing for me is how a team of dedicated professionals will do their best, yet time and time again, heros, the likes of LPL and Bosnian Bill will just put them to shame... thanks so much for the content. It's super interesting, got me into lockpicking, and its performing an invaluable service the lockpicking community as a whole. You guys rock!
Another painful but useful procedure. I guess all cars complete crash tests with dummies...maybe LPL was that dummy! Hehe.😜Kidding of course.😊 Some good points raised and a thorough review as usual. The body fared much better than I thought it would, maybe because it has magnesium & silicon in it and it is weldable, otherwise the welding process would destroy itself, so a good trait to have to slow down torch attacks also.🍺✌
The white hot from the steel while no light from the aluminum is confirmation of what you were saying about temperatures. That aluminum is wicking that heat away phenomenally.
Nice vid LPL. A few observations: Firstly, don't believe you're not concentrating the hottest part of the flame on the target area. The end is usually hottest. You appear to be playing the flame primarily onto the steel shackle because it was clearly heating up first. Not sure that's the best ploy here. The steel shackle was obviously going to dissipate the heat from whichever area you concentrated the flame upon. But I'm not convinced heating it up first advanced your attack in any useful way. The target however was the pins. Therefore I would have directed the hotter END of the flame at each side of the bar containing the pins, swapping over once one side had melted. And I believe it would had you done so. I might even shield the shackle to direct more heat onto the aluminium. Yep, I'm a Brit aircraft engineer. Otherwise, this is an inspiring vid. I'm currently working on a motorcycle security lock design, so yours and Bill's work is very very valuable. Thank you. Aluminium seems on the face of it to be a shit material for a lock. But this one proves we shouldn't fully rule it out. And where weight is an issue (as in a bike scenario), it's well worth considering, but only if the inherent vulnerabilities of the materisl's characteristics can be overcome. I'm working on this, though every viable solution turns out to be very expensive. PSWas the American lock thinner cast aluminum? That might also explain why it melted more easily.
What a clever way to implement customer feedback and gain priceless marketing all for the cost of a single lock. Much smarter than companies pouring untold amounts into CZcams ads that I always skip, and I suspect most people do too. I will look to PacLock for my next lock.
Would love to see how this aluminum lock would handle an encounter with gallium. Should be able to sand the anodizing off, put a good dollop of gallium on - wait a couple of days for it to “soak in”, then just tear the aluminum apart almost with your fingers.
This was my first thought watching the video... Now I need to hunt down how that went. I have a bit of gallium kicking around just in case a situation arises where it would be useful.
LPL's followup: czcams.com/video/jeghGhVdt9s/video.html Someone else's video: czcams.com/video/k919f7Qi4es/video.html (faster and more dramatic, but makes me appreciate that LPL doesn't add soundtracks).
I love the way LPL and other members of the locksport community interact with these companies to try to produce the most efficient locks possible. It's really cool seeing the companies humbly take their advice
Here is my thought on another low tech defeat: The outboard retaining pin is a weak spot. I noticed that as you removed the weakened tip, that the top of the lock body has hollow spaces in it. If the aluminum has not been annealed and is brittle, you might try skipping part one and go straight to part two without any cutting needed. If so, a big plus is that part two is soundless except for the final snap Part one: Using a hack/sabre/ jewellers saw or dremel make a 1mm cut between the shackle and the outboard pin on three sides (4 sides if you can)- Tip: I would try using a jewellers saw first, threading it in behind the affixed side if possible and just garrotte in a 1mm deep cut. If time is not pressing, the jewellers saw could just cut off the whole tip. Part two, if needed, using a makeshift screw-jack: If you can not get through on four sides, take a piece of hardened screw rod the length of the shackle gap and put two deep nuts threaded on to that rod. Knurl a pattern into the outward faces of two heavy flat washers to give them bite into the aluminum and place them outwards of the nuts. Place the rod, nuts, and washers inside the gap just outside of the cuts made and force the nuts away from each other with two opposing ratcheted box wrenches. This pressure should cause the cut points to expand, shear, and the top of the body tear open at the retaining pin. You might need a second, slightly longer screw piece if the aluminium bends to much before reaching the breaking point I think that a second steel pin (or plate/wafer) should be inserted the entire width of the lock (as was done down the side in model 2) above the two retaining pins, if there is enough metal above the top of the shackle's tip to prevent my defeat. I would also not mill out any unnecessary voids in the top of the lock body.
Hello LPL, I really enjoy watching your videos but I would like to offer a couple of suggestions on this one, 1) an oxyacetylene torch would probably cut though the top of this lock in a few seconds, a plummer's torch by comparison is quite a mild heat, 2) as the lock is laid down in the vice a proportion of the heat is being transferred into the vice too quickly, my suggestion is to stand the lock up so only the bottom bit is located in the vice and therefore the heat has further to travel to the vice thereby keeping more of the heat at the top of the lock.
My compliments to the designers, they knew that that had some good ideas, they avoided reinventing the wheel and decided to bring in other recognised experts in to get their opinions. I very much respect their attitude.
Wow! After seeing you just blast straight through so many locks, it's really impressive you had to actually pick this one, and go back and forth a few times at that! A real test of skill, and a signifier of how pick-resistant it would actually be to a petty thief with only a wave rake or jiggler! Definitely means that your storage shed would be left alone in favor of the neighbor's with a master lock 😂
The cast iron vice ended up being a Heat Sink and sucked away all the heat from the alloy padlock. I have found through experience that It’s a good technique to use when welding cast iron as it keeps the welding area cooler when you can draw the heat away like this.. Great video.
All you need is a gram or two of gallium and some patience, no lockpicking skills required! Also @13:24, you have *very* nice drawer slides.... That sound makes me melt
I think he actually said "This IS a lock I would not hesitate to use." But he stuttered a bit at "is". The stutter made it sound like he was saying "isn't".
what about applying tension on the top part of the lock while heating it up to brute force it open? that technique could drastically cut down on the amount of time needed to force it open...
When you said "Aluminum" I wrote the lock off. However, the "heat sink" and heat dissipation impressed me. Seven min is a good time. The security pins are good. Thanks for the analysis. Hope you get another one with your logo. While not an endorsement, your video changed my mind.
Does having it firmly in the vice just turn the vice into a huge heatsink for the lock? Saw a diff video where you hung a lock and melted the alum body and zinc innards.
I thought I saw that lock design, then you mentioned Bill taking a backsaw to it, then the dots were connecting. Anyway it would be harder to pick if you have it adhered to the door is something.
@@SparkY0 Would certainly create an Aluminum amalgam that would fail if (as with Gallium) the surface were scratched, but would inherently be much more hazardous to handle and dispose of afterward. By comparison, Gallium is benign.
Building on another comment, I think they could offer higher security variant by simply mounting armor plates to the lock body utilizing those four mounting holes.
Interesting thought... there are a whole bunch of armored shutter locks featured on my channel. They are popular in Europe, particularly Italy. The purpose of them is add security to corrosion resistant brass locks. Unfortunately, the added complexity makes them pretty pricy.
Awesome video. I agree with your suggestion that the size of the lock helped dissipate the heat, I would suggest that the massive shackle (not to mention the lock body itself) would further have an impact there since I believe that both brass and steel are more conductive than aluminium so you would have had to get them both near to the melting point of the body before it would start to melt
I'm sure someone already commented that you can't cut aluminum with a torch, it doesn't have iron in it. I know you were not trying to cut it, but many it it. I'm just saying it. Also, I used to work construction, and whenever a key was lost or left at home for the connex, they would use welding rod to melt the loop off the lock. Lol, not as elegant as picking, but very fast. Even with the steal box over the lock. Love the videos. I have wanted to get into lock picking for years. Just to have it as another "tool" in my skills.
![[636] Bowley Lock Analysis and Update](http://i.ytimg.com/vi/qV8QKZNFxLw/mqdefault.jpg)
![[636] Bowley Lock Analysis and Update](/img/tr.png)
![[593] Gallium vs. Titalium - Abus Padlock Meets a Gruesome End](http://i.ytimg.com/vi/jeghGhVdt9s/mqdefault.jpg)
![[1493] PacLock’s 7-Pin Surprise Picked & Gutted (Model 90A-Pro)](http://i.ytimg.com/vi/VDkhqoH9jQc/mqdefault.jpg)
![[1516] Practice To Be An Unstoppable Picker!](/img/n.gif)
Love how he puts a tension wrench to prevent damage with the lockpick, then later proceeds to TORCH IT. :)
Hey. It was an appropriate gesture of appreciation for the maker b4 goin full tilt breakdance open campus on the challenge. Lol. So coo!
I get the thought process. He always tries to make sure that the covert entry won't be detected.
Although in this case, you're absolutely right. I'm pretty sure they would notice their lock being scorched and broken...
W
The fact that they actually asked for feedback and made alterations on future products based on said feedback from the locksport community is highly encouraging to hear.
Yhea I'll replace my lock with one passed by this guy
More companies should do things like that.
I agree... more industries in general should do this
he gets sent locks from companys all the time tho this isnt new
This is free R&D, one lock and postage is a small investment for a better lock!
"Apparently I'm the guy to go to when you deal with really strange and impractical ways to open locks."
yep.
IDK, if there's potential for a lock body to just wash away under a few minutes of heat from a portable torch that doesn't really raise any suspicion to carry in your truck, that seems like a practical way to take someone's stuff in the right circumstances. Good to see that this lock isn't that way.
@@MushVPeets the key phrase is "a few minutes." You would have to stay there in one position with a lit torch going ham on the entrance to somewhere without anyone actually going by and noticing you. In the world we live in people are everywhere, and more time is more of a multiplier for getting caught. If you are not in a situation where you are out in the open, you had to 1:park in a weird spot. 2: drag that torch out in the open 3: walk a suspicious route while carrying a fucking blow torch, THEN stand there and go ham on the lock.
It really is weird and impractical.
@@onlinepanic2036 Put on a tool belt, a yellow hard hat and overalls, wave at people as they pass by. You don't have to hide, you just have to look like you're hired to be there.
one word ramset
@Charles Wetherspoon Unless I misremember the Turkish Police (as I remember it) did a test (due to having a large amount of kidnappings from the homes) were they (in civilian clothing) just went to the front door, knocked and asked the person opening to take a sip from a glass of water they were holding in their hand, apparently a l disturbing amount of people actually did it.
Consider that you're now at a level when you're picking open a lock in under 2 minutes, you state "Quite a bit of fight out of this lock." Heheheh. Great job, man!
😁 Thanks.
You said exactly what I was going to say.
@@lockpickinglawyer I wasn't watching the clock and it seemed like longer, but that must be because you're so quick with everything else.
I was a bit disappointed when you cut away for putting it back together. Do any of your videos show the reassembly after you gut a core? That's something I'd like to see.
A beast
Pretty sure this good fella needs a level 33 puzzle box.
It’s a shame you had to destroy the lock with your logo on, hopefully they’ll send you antother😉👍👍
The logo was put on by the manufacturer. Read previous comments.
@@charlesxix That's the point. He destroyed a customized lock.
@@ChrisG0 a block lock with the bolt and cylinder weld shut.
I also was a bit sad about seeing this beautiful lock being destroyed. I really do hope that he received a new one.
@@ChrisG0 I don't believe he's encountered a lock he couldn't pick.
I forgot he's american and when he said "a couple hundred degrees" I was picturing the flames of hell itself.
I had the same thought!
Aye
Melting point of aluminum is approximately 200 C higher than that of zinc. Closer to 250, actually. It’s possible he was thinking Fahrenheit but accidentally stumbled upon the correct interval in Celsius. Or he was correct all along and was using an untypical unit of measurement for those from the States.
Scientific fields use metric measurements, even in the US, so he very well may have been using metric. It's so much simpler when you start to get to the extremes of temps.
@@advena996 scientists always mix units, time is imperial.
Aluminum gets brittle as it heats up. In welding it is called "Hot Short"
I believe Paclock simply used a standard extruded aluminum like heat treatable 6061 and machined it down. This differs from the metal in the American lock in that it was CAST, not machined.
Casting aluminum is not the same as extruded aluminum (like the Paclock) It is chock full of doping agents (zinc can be one of these agents along with a host of other things). This can, not so much change the melting point (which it DOES, but not by as much as you may think), but aid the casting type aluminum in melting and freezing (changing phases) more uniformly, and so the American gave way all at once, whereas the Paclock would reach melting point at different points throughout the torching, but it's chemistry is less condusive to uniform "liquidus" and conducts heat better, being more "pure" aluminum than the casting aluminum and so made it a fantastic heat-sink.
The back of the American seemed to fall out, though it is uniformly shaped.
Generally, aluminum likes to be the same temperature ALL the way around and as fast as possible.
Just an observation that ultimately means nothing.
Here is a link to an article describing hot-shortness www.corrosionpedia.com/definition/638/hot-shortness
Thanks for that mate.
Aluminium does not get brittle when hot. It starts to get soft and ductile, and can be deformed like plastic.
Also helps a bit that he's got it in that nice big metal vice. Think this is a situation where having it on the chain would actually be a benefit because the air and chain links are a much worse heat conductor in their own right.
@@erikev He's not saying that its directly brittle when hot. He's saying that the more times you heat it up, the more brittle it becomes (more aluminum oxide in the structure).
PACLOCK locks are indeed 6061.
The highest praise LPL can give: I would use this lock
Quick note: I wouldn't classify a blowtorch as a "plumber's torch" as you did in this video. It's much more useful (and the trade standard as far as I know) to refer to them by the fuel used: propane torch (hot), MAPP gas (really hot), etc. They often use the same torch head and connectors, but the difference in fuel distinguishes their use as propane will melt solder for copper pipe; MAPP gas will also melt solder but it's too hot for small pipe. Acetylene is hot enough to cut pipe.
Cheers
Heat comes from the blue tip of the torch. I use UN1001 Acetyene Dissolved. 🥵
When your everyday real people CZcamsrs actually prompt entire companies into rethinking, researching, and ultimately improving a product for everyone... That's what's up.
Yes, they should build in an internal heating element so you can just plug the lock in and it will melt all by itself!
@@mattmurphy7030 i have doubts about masterlock lol. also, a year ago, when i posted this comment, LPL wasn't quite as well known of as he is today. Deservingly too!
As it should be
@@u.v.s.5583] ]2
" everyday real people" everyday real people are not expert lockpickers
"Locksport community"? I had no idea this existed, or had a name.
David Gingras I mean... they’re typically called thieves :)
Idiots.
Defcon has some, and other locksport events go down all over the place. Some that immediately comes to mind is the locksport club in Austin, Texas or Seattle, Washington. Most major cities have one or two, Google it.
The benefits of these types of events go from designing elaborate puzzle locks for fun, testing locksmith's skills, and improving on manufacturers designs. More than a few (reputable) manufacturers have upped their game and recalled certain locks with glaring flaws.
And for the ones insinuating that locksport enthusiasts are criminals in training, that's such a simple minded point of view. That's like saying everyone who learns martial arts or trains to run fast or be an impressive marksman/markswoman or learn cyber security pen/testing are also all trying to learn to be criminals.
Edit: got more specific about locations and how to find events/clubs
Do they stretch before each Locksport event? 🤣🤣
They probably take steroids to gain an advantage too.
anything that confounds him for more than a minute, I'll buy.
"Let's take a closer look at this lock..." *immediately zooms out* Great pick as always.
At last a lock company ceo that listens to and puts into practice reviews by LPL and BB, AND reads the comments. Basically he has the smarts to save a huge amount of expensive R&D.
Hi LPL, I just wanted to chime in here. As I am actually a Plumber by trade and a Lock sport enthusiast by hobby, I should tell you that your torching technique would have been quicker had you set your flame at the correct distance from the work. The hottest part of any flame is at it's tip. I noticed you being too close and I would have recommended concentrating the flame more to the outer side of the lock body opposite of the pins. Otherwise the mention of a steel version was ideal. I made that suggestion in the comments in Bill's video review as well. Great review! Thank you!
Also, the vise probably sank some heat.
@@bytheseaaspirinshop801 I agree even though only a small part of the lock was in contact with the vise it was very close to the spot he was heating and allowed a lot of the heat to sink into the vise.
J. Wilson additionally it appeared as though care was taken to focus the heat on the shackle and to avoid heating the aluminum at the weakest point and advance the molten puddle towards the locking components. It's almost as if the LPL didn't want the heating attack to be successful. Then you see the glowing review of the review of the lock by the Manufacturer, and it's enough to make you go hmmm.
Jon Hunt I was thinking the same thing while watching, I normally love his unbiased videos but this one seemed off to me as he is focusing the heat to the only parts not made of aluminum
You said... "The hottest part of any flame is at it's tip.", I wanted to add a reference... www.bernzomatic.com/Using-a-Torch/Torch-Safety (search the page for the word 'hottest').
“Let’s take a closer look”
Camera zooms out
"Let's take a closer look at this lock..." immediately zooms out Great pick as always.
Someone else said it before u 2 years ago lol
Another thing. If it were mounted on metal, heat dissipation would be greater. If on flammable material, you'd burn the house down before melting the lock.
The comment I was looking for.
At that point, the lock is the least of your problems. 😂
Would it burn down or weaken the surface it was mounted too first?
@@elementalist1984 yeah you might as well bring an axe or sledge and bust in the door
"if you were thinking what I was thinking" no, no I wasn't even thinking
Only recently found this channel and I’m noticing something incredible. Unless I’m mistaken it seems that companies making new locks are in touch with and seek feedback from the lock picking community.
That’s genuinely amazing.
Any smart company will take feedback from enthusiasts/consumers.
*locksporting community
It's how companies test their IT setup by interfacing with the hacker community.
A good hack into a big company is seen as a job application!
@@Aengus42 lmao. Hack into the ceo's pc and leave your resume on the desktop
@@mrevilducky **lockpicking. trying to rebrand this hobby is outright pointless and ignorant. theres nothing wrong with having lockpicking be your hobby.
Hey, we know yoi like picking locks, so made a custom lock for you! We made it your favorite color, and engraved your name on it, isn't that neat... also, we need you to destroy it.
How Machiavellian! >:-)
Did you ever send him the lock?
@@AS-do6pr you a dumb one, aren’t you? It’s a comment about this video
Considering one of these to lock my bike.
They're relatively affordable for the security level, and throw in a good solid self-looping security chain and we've got something that can rival solutions that cost more, but are less effective.
Suggestion: During the heat attacks, a clock in the background and perhaps accelerated footage would be great.
It's amazing how much harder these locks are to pick in thier used environment, especially when they are ridgid, butted against the locked item. Making the lock picker contort into gymnastic positions, and leave no room for grasping, and turning tools, and even for knuckles of the hands in a grasping mode, changes the security rating.
Maybe they just prototyped it in aluminum due to its relative ease of milling and will also offer a steel version too.
Spot on! We always start aluminum to test the market and then move to hardened steel if the concept looks good. We're going to keep the aluminum body as an option mostly because of the weight savings... for bicycles and motorcycles where carrying a 1lb lock that's pretty darn good versus a 4lb lock that's super strong (but kills your back!) is a good option.
PACLOCK PRES. Awesome, that sounds like a good move! 🍺✌
@@paclockpres.9805 I know this is an old video and post but this right here not only shows that PacLock listens to the Lock picking community but also reads the comments of the videos. That, to me, is just as impressive as their locks. I just started on this journey and hope to achieve the 200k Club.
@@dechert3602 Thank you! We'll be having yet another prototype posted onto our CZcams account within the next few days for comments and testers! And good luck with your 200K Club admissions!!!!
points for the logo - i thought it would immediately vaporize
The logo was made using a laser. The logo would only disappear once all the paint on the lock completely disappeared and the lock became white.
haha I like how the company colored the lock with diecast blue (which gives off toxic fumes at high temperatures) and then they were like “here you go, by the way do you think you could melt it?” Trying to murder the LPLawyer so he can’t defeat any more of their locks, nicee that’s mad smart
Cool! I found these in a search a while back and lo and behold BosnianBill and LPL not only review them but PacLock improves them accordingly. Awesome! Yay PacLock and LPL!
merlin308 I have to applaud Paclock for this.
Merlin Same here. LPL and BosnianBill really opened my eyes to how vulnerable some lock brands are. After seeing how receptive Paclock has been to suggestions and security I ordered a couple from HD. They will be used for protection and of course... play 😎
"A lock I would not hesitate to use"
Is there any higher praise? No there is not.
I think there was another negative before that:
19:23 "This isn't a lock I wouldn't hesitate to use".
Probably meant to say what you wrote, but it threw me a bit when I heard it.
"Apparently I'm the guy to go to when you deal with really strange and impractical ways to open locks" Damn you had me rolling with that xD
where did you roll to
Your videos have the absolute best commentary while you are picking the lock. That is the most valuable part for those of us who are trying to improve our skills. Also, your camera is in focus! Bill's videos drive me nuts with his constantly blurry close-ups. Looks like this lock is a good training lock for pickers. Thank you for another great video.
Because bill uses auto-focus and LPL uses manual.
"Focus you fack"
Calm and methodically laid out description, pedagogical and thorough, I like that. Only one thing worries me and that is that "wrong" people who follow you, learn very useful for them.
But the rest of us learn what to observe. It's great
Thanks for a very good page.
Carsten Sweden
The essential difference between the liquid-melted lock body and that of this lock is that an aluminum wrought alloy was used here, as used for the production of extruded semi-finished products. Here the practically melted material at the outlet of the nozzle must have sufficient strength to hold the desired shape. A cast aluminum, on the other hand, has to melt thinly in order to fill even fine structures in a mold.
So much for my knowledge of materials science from studying mechanical engineering.
What has my life become when I will gladly sit here and watch 7 minutes of silence lock melting simply amazed at the skill this man has
Pack lock
Blue one can be super secure with a hardened cup cover bolted from inside door with 1 large hardened bolt.
Also that anti hacksaw pin should be hardened and looose so it rolls with hacksaw blade
Glad to see a company actually putting there product through people that actually know how to pick a lock to improve the tech
Your attention to detail and the practice of routine is incredible. You know full well you're about to completely destroy the lock with a torch and make it totally unusable. But you still protect the bottom of the lock from damage dissed by the pick anyway.
It seems like a slide hammer blow or two would pop the pins that hold the shackle in place through that thin layer of aluminum.
I like the design that it can be bolted to a surface, and if made from steel and toughened as stated would be a great lock to buy if available in the UK
It's amazing how much I enjoy this. I think you cadence and tone as well as knowledge make the pace that sweet spot for information assimilation & entertainment. I'm a big time nerd, so this is my jam. I specialize in ballroom dance history, but we're cut from the same mold of wanting to endlessly learn. This might be our intellectual interface. Thank you, you are my nerdy ASMR.
Very informative from a physical sciences AND engineering perspective! Good work!
That American lock looks like it might be cast aluminum. In my experience, cast aluminum is more brittle than it’s barstock counterpart. Given that the PacLock looks milled, I wouldn’t be surprised if it was made of a pretty tough grade aluminum. I wonder tho if you could’ve gotten it open faster by heating further toward the elbow and then prying with some channel locks or vice grips to get better leverage over the needle noses. Very cool stuff +1
At last a lock company that realises that certain skilled people like LPL can save them thousands of R&D money, and have fun at the same time!
Nice review. I like your objective approach to this. I don't know if that's the right word but you and Bill both do a great job at quality info / time ratio. Thank you.
Portland, ME
I don't even know what to say I am not a lock picker but I just love listening to these videos
Awesome video. I also hate to see a good lock destroyed, but I believe its ok in the matter of science and learning. This is how we all learn to improve things. I'm proud of PacLock for actually listening to the end user. Thank you for sharing this. Also, great picking LPL always a pleasure to watch you work the pins.
Why is this so entertaining. I love his soothing voice and calm speaking
the tip 9:55 onwards is the kinda shit that changes your game forever but LPL just drops casually. legend
The softly spoken lock assassin! Thorough examination as usual. Love this stuff.
I definitely support this lock, this took a long time for him to pick and hes usually able to get it in like 30 sec-1 min
I'm absolutely hooked on the channel, LPL is amazing, the skill and knowledge he has is freaking great. I don't even have anything padlocked, but I now know if I do there's plenty I don't buy!
Great job by PACLOCK. I'm definitely looking for their locks next time I need one for myself
Being made out of aluminum my biggest concern out of those you addressed would be a prying attack. Using a pry bar and leveraging off of the hasp or chain and prying the top you would think it would bend or outright break quite easily. There isn't much material on the bottom of those steel pins that hold the shackle, and even with a thick steel pin inserted into the "neck" of the lock it should still bend quite easily.
The sharp corners inside the mouth could also be a weak point. Having them rounded would increase strength.
The only way I see practical to damage this lock by leverage attacks would be mitigated if not completely eliminated by that steel rod, unless this is locked to a solid steel door or some other surface hard enough where you could bend the entire lock without damaging the surface that's mounted to. Any lock not made of solid steel is going to be a low security affair so we're talking stuff like fence gates, sheds maybe get a cheap chain and secure your relatively cheap bike to it or similar. Situations where the lock is secure enough that if the thief wants the stuff they're likely just going to take the easy route of say destroying the chain or getting a sledgehammer and just busting through the shed walls or whatever
Good video!
Would be interested to see a picking attempt with the lock bolted to a door in real life application.
I totally agree with the steel lock body. Even though PacLock installed steel rods in the new design, aluminum is very soft and can be manipulated. A steel lock body would be more expensive but that point is moot if you are securing something valuable. Great video!!
you are able to talk very clearly and it seems like you think about every word that comes out of your mouth before you say it. which makes you very easy to under stand.very well spoken and the best locker picker iv'e ever seen.its crazy how easly you bypass some of those, incredable
Great video brother. I agree with your observations, this lock definitely dispersed the heat better than the 1100 preventing it from getting hot enough to melt aluminum under those pins in the same way as the other lock. Thanks for the review!
interesting and very informative as always
I suppose, if you were bolting it to a surface, you could include a 2-3 mm plate of very hardened steel on the outside face to gain a lot of protection with only a little material.
I love that lock you melted, it looks perfectly fine from the front and when you turn it not so much lol
Hey there @LockPickingLawyer , awesome video! It was entertaining and I enjoy how you describe as you go. That is very helpful to me, as an in-training locksmith, to watch your hands work, where you're at within the pick and the action happening. I think you're great at what you do and your videos are awesome.
I'm pretty familiar in the destructive opening techniques and have background on construction, structures and support and if I may just share my opinion.
If the idea of the video was more for presentation during the destruction, then the already unlikely of ability to destroy this lock in this manner, then that's no problem. I guess what I mean is that in order to properly make an attempt such as this or similar "attack openings" would be to do in in real world situations.
My example would be like if you were really trying to get whatever this lock was supposed to be protecting, perhaps the time it would realistically take to get into any lock, just out in the world, plus the determination and tools of the potential thief.
By about 2.5 minutes into the demonstration, I think that the red-hot steel could possibly have been pried and essentially reshaped it's locking ability into the block of also steel pins, it could have popped, potentially.
Personally, having the mostly common knowledge of hottest burning portable torch and gas setups, I think the yellow map gas can, from an above angle and the position of the torches flame, I think the lock might have opened in a fraction of the time. Of course I'm not intending to insult your work, but coming from my knowledge and background, desperation can make any lock openable.
I think that if the company of the lock was relatively confident in its core's ability to seem the biggest hassle, they should look to have a real-world torture test done, perhaps also as a review.
With that said, I really enjoy your work and I hope that we continue to improve our ability to protect ourselves and thanks to people like you and @Bosnianbill ,we might just get there one day. Thank you!
I’ve been a “machinist/toolmaker/ mold maker” for well over a decade. I have extensive experience with a multitude of materials. When I hear “it made of steel!”... many questions come to mind. To me steel is butter. What kind of steel? What’s the Rockwell? Yield strength?
Why are we still using steel for locks? Is it a cost issue?
Steel is relatively easy to shape with the right tools, what else would you make locks out of though? Materials like tungsten or cobalt alloys are too brittle or too expensive, basic titanium is easier to cut than steel aside from the binding issues, and most everything else would be worse in all categories. The only thing I think would be better is properly heat treated beta-ti or 6alv4. At that point, a high toughness tool steel with a proper heat treat is still going to be better though, and cheaper as well.
To excuse anything I'm missing though, most of my experience comes from bladesmithing and not from a general material science standpoint.
The craziest thing for me is how a team of dedicated professionals will do their best, yet time and time again, heros, the likes of LPL and Bosnian Bill will just put them to shame... thanks so much for the content. It's super interesting, got me into lockpicking, and its performing an invaluable service the lockpicking community as a whole. You guys rock!
I’m impressed with how long this lock took to even soften to the point where LPL was able to bend the metal back.
I only just noticed what your logo is, and I love the symbolism.
Another painful but useful procedure. I guess all cars complete crash tests with dummies...maybe LPL was that dummy! Hehe.😜Kidding of course.😊 Some good points raised and a thorough review as usual. The body fared much better than I thought it would, maybe because it has magnesium & silicon in it and it is weldable, otherwise the welding process would destroy itself, so a good trait to have to slow down torch attacks also.🍺✌
When he’s picking it reminds me of my dentist checking my gum line ...
I love that not only is your favourite colour blue (obvs the best colour), but you have a favourite shade too! 💙
The white hot from the steel while no light from the aluminum is confirmation of what you were saying about temperatures. That aluminum is wicking that heat away phenomenally.
Nice vid LPL. A few observations:
Firstly, don't believe you're not concentrating the hottest part of the flame on the target area. The end is usually hottest.
You appear to be playing the flame primarily onto the steel shackle because it was clearly heating up first. Not sure that's the best ploy here.
The steel shackle was obviously going to dissipate the heat from whichever area you concentrated the flame upon.
But I'm not convinced heating it up first advanced your attack in any useful way.
The target however was the pins. Therefore I would have directed the hotter END of the flame at each side of the bar containing the pins, swapping over once one side had melted. And I believe it would had you done so. I might even shield the shackle to direct more heat onto the aluminium. Yep, I'm a Brit aircraft engineer.
Otherwise, this is an inspiring vid. I'm currently working on a motorcycle security lock design, so yours and Bill's work is very very valuable. Thank you.
Aluminium seems on the face of it to be a shit material for a lock. But this one proves we shouldn't fully rule it out. And where weight is an issue (as in a bike scenario), it's well worth considering, but only if the inherent vulnerabilities of the materisl's characteristics can be overcome. I'm working on this, though every viable solution turns out to be very expensive.
PSWas the American lock thinner cast aluminum? That might also explain why it melted more easily.
close your eyes and listen to his voice: the holographic doctor from Star Trek is teaching you how to pick locks. you can't unhear it.
the speed of your picking is just so unreal...I hope to get there one day! #inspiration
What a clever way to implement customer feedback and gain priceless marketing all for the cost of a single lock. Much smarter than companies pouring untold amounts into CZcams ads that I always skip, and I suspect most people do too. I will look to PacLock for my next lock.
Would love to see how this aluminum lock would handle an encounter with gallium.
Should be able to sand the anodizing off, put a good dollop of gallium on - wait a couple of days for it to “soak in”, then just tear the aluminum apart almost with your fingers.
Stay tuned. 😉
This was my first thought watching the video... Now I need to hunt down how that went. I have a bit of gallium kicking around just in case a situation arises where it would be useful.
LPL's followup: czcams.com/video/jeghGhVdt9s/video.html
Someone else's video: czcams.com/video/k919f7Qi4es/video.html (faster and more dramatic, but makes me appreciate that LPL doesn't add soundtracks).
I love the way LPL and other members of the locksport community interact with these companies to try to produce the most efficient locks possible. It's really cool seeing the companies humbly take their advice
binge watching your videos today ✌😁 about to try and pick every lock i can find in my house lol
I love how you also consider economics of the design.
Here is my thought on another low tech defeat:
The outboard retaining pin is a weak spot. I noticed that as you removed the weakened tip, that the top of the lock body has hollow spaces in it.
If the aluminum has not been annealed and is brittle, you might try skipping part one and go straight to part two without any cutting needed. If so, a big plus is that part two is soundless except for the final snap
Part one:
Using a hack/sabre/ jewellers saw or dremel make a 1mm cut between the shackle and the outboard pin on three sides (4 sides if you can)-
Tip: I would try using a jewellers saw first, threading it in behind the affixed side if possible and just garrotte in a 1mm deep cut. If time is not pressing, the jewellers saw could just cut off the whole tip.
Part two, if needed, using a makeshift screw-jack:
If you can not get through on four sides, take a piece of hardened screw rod the length of the shackle gap and put two deep nuts threaded on to that rod. Knurl a pattern into the outward faces of two heavy flat washers to give them bite into the aluminum and place them outwards of the nuts. Place the rod, nuts, and washers inside the gap just outside of the cuts made and force the nuts away from each other with two opposing ratcheted box wrenches. This pressure should cause the cut points to expand, shear, and the top of the body tear open at the retaining pin. You might need a second, slightly longer screw piece if the aluminium bends to much before reaching the breaking point
I think that a second steel pin (or plate/wafer) should be inserted the entire width of the lock (as was done down the side in model 2) above the two retaining pins, if there is enough metal above the top of the shackle's tip to prevent my defeat. I would also not mill out any unnecessary voids in the top of the lock body.
From what I can tell these are made of solid aluminum bar stock so they're only machining what they need to because that's the cheapest option
"I'm going to melt it. Here's how to keep it pristine while picking, before I do that."
I like how you put the tension wrench to avoid making a dent on the padlock........before you torch it !!! :D
Hello LPL, I really enjoy watching your videos but I would like to offer a couple of suggestions on this one, 1) an oxyacetylene torch would probably cut though the top of this lock in a few seconds, a plummer's torch by comparison is quite a mild heat, 2) as the lock is laid down in the vice a proportion of the heat is being transferred into the vice too quickly, my suggestion is to stand the lock up so only the bottom bit is located in the vice and therefore the heat has further to travel to the vice thereby keeping more of the heat at the top of the lock.
"So uh, we sent you a blue lock, right?" "Yes" "Why did we receive a brown and broken one now?" "..." "Well?" "This is The Lock Picking Lawyer..."
A 26 minute lpl video. This has to be good.
My compliments to the designers, they knew that that had some good ideas, they avoided reinventing the wheel and decided to bring in other recognised experts in to get their opinions. I very much respect their attitude.
Wow! After seeing you just blast straight through so many locks, it's really impressive you had to actually pick this one, and go back and forth a few times at that! A real test of skill, and a signifier of how pick-resistant it would actually be to a petty thief with only a wave rake or jiggler! Definitely means that your storage shed would be left alone in favor of the neighbor's with a master lock 😂
Totally missed the opportunity to turn the melting vid into an old-timey silent movie.
You mean play it at a faster speed with a pianola proving accompaniment?
Yakkety Sax
@@gary_rumain_you_peons Yep.
czcams.com/video/piOFPH7FyQI/video.html
Imagine he gets arrested and while he's in the car all the cops just hear "a nice click out of 1, click on 2..." and he rips off the handcuffs
Feeding my theory that he’s lawyer by day, hitman by night, CZcamsr by hobby.
The cast iron vice ended up being a Heat Sink and sucked away all the heat from the alloy padlock. I have found through experience that It’s a good technique to use when welding cast iron as it keeps the welding area cooler when you can draw the heat away like this.. Great video.
All you need is a gram or two of gallium and some patience, no lockpicking skills required!
Also @13:24, you have *very* nice drawer slides.... That sound makes me melt
19:23
LPL: And this isn't a lock that I would not hesitate to use.
So, you _would_ hesitate to use it? 🤣
I think he actually said "This IS a lock I would not hesitate to use." But he stuttered a bit at "is". The stutter made it sound like he was saying "isn't".
what about applying tension on the top part of the lock while heating it up to brute force it open? that technique could drastically cut down on the amount of time needed to force it open...
I love to see that in each and every video of LPL's, the comment section is always so positive. Keep doin your thing sir.
When you said "Aluminum" I wrote the lock off. However, the "heat sink" and heat dissipation impressed me. Seven min is a good time. The security pins are good.
Thanks for the analysis. Hope you get another one with your logo.
While not an endorsement, your video changed my mind.
After reading this comment all I can think about is
He said,"aluminum" the lock is bad change my mind
"so let's take a look at this lock"
*zooms out*
Does having it firmly in the vice just turn the vice into a huge heatsink for the lock? Saw a diff video where you hung a lock and melted the alum body and zinc innards.
I thought I saw that lock design, then you mentioned Bill taking a backsaw to it, then the dots were connecting. Anyway it would be harder to pick if you have it adhered to the door is something.
Wow awesome lock for just you. That is really cool.
You say it's Aluminum? Would it be susceptible to a Gallium attack?
if you have 5 hours... you see how thick that thing is?
You only need to attack the pins that hold the shackle in, though, which is where he was attacking with the torch.
This was my thought, starting around the pins above at the top.
Or mercury?
@@SparkY0 Would certainly create an Aluminum amalgam that would fail if (as with Gallium) the surface were scratched, but would inherently be much more hazardous to handle and dispose of afterward. By comparison, Gallium is benign.
Building on another comment, I think they could offer higher security variant by simply mounting armor plates to the lock body utilizing those four mounting holes.
Interesting thought... there are a whole bunch of armored shutter locks featured on my channel. They are popular in Europe, particularly Italy. The purpose of them is add security to corrosion resistant brass locks. Unfortunately, the added complexity makes them pretty pricy.
Awesome video. I agree with your suggestion that the size of the lock helped dissipate the heat, I would suggest that the massive shackle (not to mention the lock body itself) would further have an impact there since I believe that both brass and steel are more conductive than aluminium so you would have had to get them both near to the melting point of the body before it would start to melt
I'm sure someone already commented that you can't cut aluminum with a torch, it doesn't have iron in it. I know you were not trying to cut it, but many it it. I'm just saying it.
Also, I used to work construction, and whenever a key was lost or left at home for the connex, they would use welding rod to melt the loop off the lock. Lol, not as elegant as picking, but very fast. Even with the steal box over the lock.
Love the videos. I have wanted to get into lock picking for years. Just to have it as another "tool" in my skills.