Silver Pouring 2000° Silver into a Wooden Mold! EPIC!
Vložit
- čas přidán 12. 12. 2019
- In this video I film myself Silver Pouring 2000° Silver into a Wooden Mold! Ever since I started pouring silver I have wanted to do a wood pour. The lines on these pieces end up looking so great and I am loving the way that these wooden silver pours turned out! In this video I also show myself casting a pure silver golf ball as a bonus!
How to Make a Pure Silver Golf Ball
• Making a Pure Silver G...
Check out SD Bullion for GREAT DEALS on Silver and Gold!
sdbullion.com/dragons
Below are some AWESOME products that I use:
Inexpensive Scale for Weighing Silver and Gold
amzn.to/35sgcQW
Black Ring Capsules for most Silver Bullion Coins (38mm)
amzn.to/37oARH7
Black Ring Capsules for American Silver Eagles (40mm)
amzn.to/2s79Wj3
Gloves for Handling Coins
amzn.to/2QGCKJx
Paypal/Email:
silverdragons47@gmail.com
Also check me out on Instagram:
/ silverdragons47
If you want to mail me anything here is my address:
S. Dragons
P.O. Box 304
Gresham, OR 97030
Thanks for watching!!
Disclaimer: Some of the links are affiliate links where ill earn a small commission if you make a purchase at no additional cost to you.
Topics I cover in this video: silver pouring, pouring silver into wood, wood silver pour, pouring silver, silver pour, poured silver, wooden mold silver pouring, pouring 2000 degree silver, silver vs wood, wooden mold silver pour
#pouredsilver #silverpouring #silver
So, two things I would recommend doing:
1. Sand the surface of the word. This stops splintering and if it comes from a blue or orange box store removes the factory varnish they spray on a a sealer.
2. Braze the entire board with a torch before you pour. This will stop the silver from skittering and popping as the surface water will already be evaporated and also acts to harden the wood. No need to recaste the first bar as well.
My two cents
Do you know where to buy the equipment to melt silver with, and castings for a mold? Thanks
Elysium not a bad idea! someone else suggested baking the wood fist 🤷🏽♂️🔥🐉
@@SilverDragons47 that's a good idea. why not both? I could see maybe 200 degrees for an hour in the oven then harden off the surface gently with a torch. The popping of the molten metal looks very dangerous and is, of course, caused by moisture in the wood rapidly evaporating. Not only that you will inevitably not recover all of the silver that flys everywhere. I could be wrong and maybe wood will do this regardless of the precautions, but it would be interesting to see the contrast reaction of baked and torched wood vs untreated if any as well as the life of the mold.
@@philiplippens2690
devil-forge.com/gas-furnaces/38-fb1sb.html
Is the furnace I have. bigstackD Casting does videos with one. You can buy molds and a proper crucible on amazon. Likewise you can watch TheKingofRandom's video on a inexpensive diy foundry. I'd also watch The Essential Craftsman for some handy tips about smithing work before committing to anything.
Note: NEVER melt or heat up galvanized anything. Extremely toxic. Do your research before anything and have fun melting stuff!
@@MrLookatmyhat
Thanks very much for the advice and where to buy. 👍
This only just now popped into my feed.
What a fantastic effect 😮.
The third bar looked like a whole shell peanut 🥜. The sprue made a nice stand for the golf ball. What great fun on the castings!
Good timing my friend they just showed up yesterday afternoon in the mail. Awesome job they came out just like I thought they would. Thanks again. I'm working on the next project now...
Mr sawyer i’m glad they made it there and that you like them! thanks for the opportunity my friend!!! I had so much fun with this project 🔥🐉
I like the second one better, because it came out better
The golf ball is my favorite by far.
That bar is awesome! I’m hundred percent hijacking this idea, with respect of course lol
Great video, thank you for all the work! But please keep that music low, my ears almost died ;)
REALLY COOL!! 👍💓
Great pours love the Golf Ball
A video using the golf ball would be entertaining af
Jumex Suplex lol maybe i’ll try one in the future 😂🔥🐉
Whoa!
that is cool my friend! gotta give this a try, gonna find some solid old oak and give it a pour!
Awesome pours
Wow that detail is fantastic!! 😳
SilverLimey 79 yeah I can’t believe the finish!!! 🔥🐉
These are awesome!
Whimsymaker Thanks so much my friend!!! 🔥🐉
Very cool! Thanks for sharing SD!
Viking4Jesus Thanks so much my friend!! 🔥🐉
Sweet vid, bro! Very cool to watch. 😄👌🏼
Yankee Stacking thanks Yankee it was fun to make 😁🔥🐉
That’s sick
So awesome
Ziaad Abrahams Thanks so much my friend!! 🔥🐉
Very cool stuff!
Stacks & Stuff thanks a bunch my friend!! 🔥🐉
This video was SOOO cool to watch!! Thanks Silver Dragons! You Sir, are an ArTEEEEST!!! That was BADASSERY!!
nerotikzombie thanks I had a lot of fun making it! 😁🔥🐉
Awesome pours!
veritasfiles thanks so much!! 🔥🐉
Wow interesting... Glad to see you venture into other projects. Congrats buddy. 👍
SilverLimey 79 thanks a bunch my friend! it was a fun project 😁🔥🐉
I'm a pyro so this was very fun to watch . . Bar looks like a brain. Love it.
Kevin Belcher thanks! it was burning quite a bit 😂 I love it as well 🔥🐉
Awesome pour! Antiqued bar looks really nice.
Greg Levicoff thanks a bunch! that was my fav as well 😜🔥🐉
Nature really makes beautiful molds! 💙💙💙
Silver Damsel oh it does for sure!!! I love it!! 🔥🔥🔥🔥🔥🔥🐉
I love the wood pours. That makes two reasons I need to get a Dremmel.
Sterling Cannabis lol you NEED one for sure 🔥🐉
I love these bars Silver dragons. Great content and work all around.
SILVERDRAGON STACKER Thanks so much my friend!! 🔥🐉
Awesome pouring
Silver Wheels I had fun with it 😁🔥🐉
Love wood pours!
JustAnotherAverageStacker thanks I love em as well!!! 😁🔥🐉
That's my golf ball you just watch the Dragon pour and believe me, it's even cooler in person!
Mike Yox lol it was a fun pour my friend! 👍🏽🔥🐉
Super fun pour!🔥🔥🔥
Fiat Destroyer thanks a bunch Fiat Destroyer!!! 🔥🐉
That looks amazing. I need one of these in my stack!
Benjamin Denney Thanks so much my friend!! i’ll have to make more 🔥🐉
cool technique. the result is really unique.
Jorge Luna Thanks so much! I agree!! 🔥🐉
Burn baby burn... for the love of art 💥
Silver Nuts I love it too my friend 😁🔥🐉
@Silver Dragons pouring into that wood was really cool! I've never seen anything like that before. Honeycomb is exactly what I was thinking too! Great job!
This is really cool! This is one of those times that makes me want to start pouring. Have a mold of my own to pour and maybe sell. Just thinking out loud. Also, to me it looks like dragon/reptile scales.
Silver Coin Outdoors Thanks so much my friend!!! you should do it!!! 🔥🐉
Very cool
Womble Stacker Thanks so much my friend!! 🔥🐉
Great video.
Professor Statisyahu thanks my friend! 🔥🐉
That is absolutely beautiful
Grandpa Joe Thanks so much my friend!!! 🔥🐉
That is sweet
Dude!!
You should make a golf ball and leave the portion you cut off on.
Twould make for a great stand for the mantle or desk
Jonathan Davis you mean like this one? 😂 czcams.com/video/YTbmCWDhfm0/video.html
Silver Dragons
Dangitt!! I thought I had a novel idea lol
How many oz’s would I need to send you to git you to make one for me?
I’d send you a constitutional silver gift of course for your time and expertise
Jonathan Davis they take a good amount of work... shoot me an email if you want and we can work it out! silverdragons47@gmail.com
😍🤙👍 WOW love the wood pours bro. Super cool video dude. This is definitely on my list of things to do.
Silver Taniwha Thanks so much my friend!!! you should do it for sure!!!! 🔥🐉
3 more awesome pieces! Antiquing 1 bar and leaving the other raw is nice.
New Way thanks! yeah that is what he wanted 😏👍🏽🔥🐉
Gorgeous! I love those wood molded bars. So cool, man. ^_^
Matthew Anderson thanks a bunch my friend! I love em as well!! 🔥🐉
Unique gift for golfers! Great workmanship skill! - Joey From Seattle
Joe Costello Thanks so much my friend!!! 🔥🐉
That second one was fantastic.
Barbara G. Seaverson thanks a bunch! I had fun with them 😁🔥🐉
Awesome work. I love unique pours.
ROSA agUIRRE thanks and I really love them as well!!! 🔥🐉
@@SilverDragons47 I need a legion sticker . Do I buy one or how do I get one. I am part of the 47 legionnaires 🤙🤙🤙🤙🤙
ROSA agUIRRE I will be sending them out with all of the pours ordered from the January 3rd pour party and I have a big version in my merch store 👍🏽 that’s all I have right now 🔥🐉
soo freaking cool. wouldn't have thought wood would be able to hold shape at those temps.
Tori G it is cool for sure!!! I was pretty sure it would work as I have seen other people do it before me 😏🔥🐉
Can you revisit this idea! maybe have a custom design routered out of the wood! Cool video!
That is so cool! love the video! see you somewhere soon my friend!
Victoria Roman Carter thanks! see you on the tube! 👍🏽🔥🐉
Neat. Maybe pre-toast the wood with a torch so the first pour isn’t so bubbly?
A sand mold of a corncob would probably be cool
I think slightly scorching the wood with a blowtorch would reduce moisture and the silver spitting out
Wood pours are awesome!! The only ones I have in my collection are 2 that JAAS made for me and they are amazing!! Have fun with it buddy!
LOVE THE MUSIC SD !!! 😎😂
Normal_ Norm thanks! party time 😂🔥🐉
Cool video Silver Dragons. I've been wanting to do this too.
Dusty Roads thanks! you should give it a try it is quite fun 😁🔥🐉
I made a furnace by cutting a 55 gallon Harley Davidson oil drum down to a little above half. Added a couple layers of thermal blanket with refractory cement over that. The homemade LP burner is a super simple design which uses a hair drier for forced induction. A low setting is just right, while high pushes the limits of what my cement can handle. I'm using a large salamander graphite crucible at the time, but it's been used primarily for copper. The problem I have in using silver is that the crucible I have is so small. My plans are to do the Oak mold in copper. I can't wait. It's going to be awesome.
Hello Silver Dragons
hello I will have a question ... Which oven do you use? can i have the link :)
I'm guessing the splattering on the first pour is due to moisture in the wood? Likely has gas pockets? Can you pre-char the wood to reduce the moisture? Also prevent some of the excess burning?
This is great bud. It's neat to see you wandering around in different pouring mediums. My mentor, "Ag Ender" is in my eyes the king of wood pours. He always had a can to cover the wood pours that keeps the topside of the pours nice and with a lot fewer dimples and shaky things on them. Check him out son.He was monumental for getting me going when I first started pouring. Like this I have done a number of sequential wood pours for various folks. Number them so they can see them change from pour to pour. I finally now have all the bolt cutters from 8 to 42 inch. The big boy will chew up a 10 oz bar in no time so I don't need to make near as much shot as I used to. Well bud, , , What a fun post. Great to see you doing pours from different molds than just graphite. WOOHOO ON YOU SON !
Where do you buy the equipment to do this with? Thanks
Tomoko's Enterprize i’ll have to check him out thanks for the tip my friend!!! yes now I have done clay, graphite, water, and wood. I wonder what is next 😏🔥🐉
philip lippens czcams.com/video/jW0YX1e0gxk/video.html
@@SilverDragons47 Shoot for the moon son. Who knows maybe you will discover some new medium to pour into no one else has tried eh.
@@SilverDragons47
Thanks 👍
Sweet pours kinda reminds me of the tombstone bars that golf ball is a nice piece there
stack attacker Wager thanks a bunch and I can see it! 👍🏽🔥🐉
Would it just be easier to use copper or aluminium first and then on the final pour use silver? Just thinking saving having to dredge impurities out of the first two pours of silver on remelt?
I have to wonder if different types of wood would give any significantly different results... For example mahogany or teak with very tight woodgrain. The oak you used seems a great first time choice...
Also wonder if a wood burning pen for pyrography would allow you ( or others) to add artistic elements to the bars...
Just some thoughts...
Great video.... BTW
So awesome man! The Silver golf ball is epic!! Imagine doing a Silver basketball, how cool would THAT be!! lol
Bruce Liggett lol a basketball would be like 6 figures 😂😂😂🔥🐉
Those are awesome! Dragon skin haha.
Ninja Stacking lol oh Dragon skin for sure!!! 🔥🐉
Nice wood pours love the golf ball too who has one of his golf balls ?
Roczilla 😂😂😂 i’m not sure how many golf balls are out there but it’s less than 10 🔥🐉
awsome, ;) just mabe my second ingont of 925 silver bar ;) nice video ;)
Johnny Björkdahl nice and thanks!! 👍🏽🔥🐉
I'm sure by now you know why the mold was spitting as you did mention that before. I say this more for the casual scroller. The reason why is due to the water content in the wood. As it heats up it causes the water to evaporate which then creates gas causing the silver to "spit". This is an interesting idea but if I made a suggestion id say next time to heat the hole in the block of wood before casting to prevent the moisture issue. Probably not going to do a ton but the first pour probably wont be as violent as this one.
I liked that golf ball, I would have bought it if you have not cut the leg of the golf ball
I was wondering why he clipped that as well
Where do you buy the equipment to melt silver with, and how do you make a mold? I've thought about doing it for years. Thanks
philip lippens mostly ebay and amazon... good luck!! czcams.com/video/jW0YX1e0gxk/video.html
How do I use a torch to burn the board first in the second one usually comes out good
Mrt Stacking yeah that is not a bad idea at all... thanks!! 🔥🐉
Do you always use quarter sawn? Have you tried flat sawn? If so, how were the results? Thanks.
Nice work! Cooler than the scottsdale nuggets.
Silver Fox thanks I really appreciate that!! 🔥🐉
Fascinating, even slow motion is fast.
charles davis lol yeah it’s crazy how it looks 😏🔥🐉
Interesting. Bybee made that 30 ozt sphere but you did it first witha. Golf ball lol
Oh the humanity!!! Dragon tears everywhere.
john m 😂😂😂😂 he was weeping! 🔥🐉
3rd one looked like a flatten silver bar planters nut.
Bobby Parks lol it kinda did 😂🔥🐉
Those are amazing. The golf ball looked like it was on a tee before you sniped off the excess from the poor. Would be cool to display it like that in my opinion.
That Bearded Veteran like this one 😏 czcams.com/video/YTbmCWDhfm0/video.html
Now if you melt something that’s maybe Sterling or less than .999, do the impurities burn off?
Great vid! Would love a quench cam.
Robert H lol I know I need one 😂😂😂😂🔥🐉
Second one would have made a cool pendant
Looks like EPCOT- the ball.
Yeah thats pretty epic lol
Bryan Woodard thanks I agree 😁🔥🐉
I hate you guys. It was bad enough all these vids got me addicted to stacking. Now you had to go and start pouring bars. Now I am searching for a furnace and molds. I really didnt need another addiction!
It is a vise like no other bud !
Aquarium Samurai 😂😂😂 this one will suck you in my friend. it’s a lot of fun though 🔥🐉
Look at those little spider cracks
Silver Wheels or Dragon scales! 😜🔥🐉
That’s money 💰
Do you have a website were you sell your silver creations? Wondering how much you sell your silver for over spot? Really love the wood molds.
psychout I do not I sell my pours right now live. my next party will be on January 3rd 👍🏽 I charge $28 per ounce with free shipping. these were all trades 🔥🐉
@@SilverDragons47 - I'll make sure to watch on Jan 3rd, beautiful pieces.
I thought you were rich spilling all that silver until I looked at the date
Do u sale any of your silver pieces u make..
yeah www.silverdragons47.com 🔥🐉
I'll second the idea of spanking a silver golf ball with a club. You should probably borrow your neighbors clubs for this tho😜
Brandon Curry 😂😂😂 iv got some old clubs i’ll give it a go. 🔥🐉
I thought you would of tapped the wood to get the ripples on the back side.
You know what would make that golf ball? A gold tee. Oh Yeah.
SILVERDRAGON STACKER 😂😂😂 maybe someday i’ll make one. gemini silver made me a silver tee 🔥🐉
Are you able to sell them pouring your own? And if so where?
jaylen allen yeah I sell them to people on youtube and instagram 🔥🐉
The one on the right is best and I would've left the golf ball on the T.
Agree! I like the ball on the tee!
Barbara G. Seaverson you mean like this one 😁 czcams.com/video/YTbmCWDhfm0/video.html
Kevin R check out this one! czcams.com/video/YTbmCWDhfm0/video.html
@@SilverDragons47 Absolutely. I love it.
Hi Silver dragon I'm new to your channel
Adolfo Cardoza welcome to the 47th Dragon Legion my friend! 🔥🐉
@@SilverDragons47 thank you
I'm no silver pourer but maybe if you burned the wood with a torch 1st like the molds so the silver doesn't pop and spit out everywhere
Jonathan Reese yeah probably or maybe if I just bake the wood 🤷🏽♂️🔥🐉
looked dangerous the way it spat them shots out, wouldn't want them hitting you at over 1000c!
Call that dragon skin
Emil and Teresa Kamar yeah that really is the best name 😜🔥🐉
I’m Really Surprised The Fire Didn’t Catch The Rest Of The Wood !
steelersjourney11111 lol it stayed pretty contained didn’t it 😏🔥🐉