sometimes, the bricks are the same size just layed once on the long side and once on the shortside, and when placed on the long side two bricks are used so that the width is the same as a brick layed on the shortside, its cheaper than buying 2 different sets of bricks :)
At the beginning you say the normal brick is in 2 sizes (normal brick & double brick). I just want to clarify that it isn't a double brick, those smaller bricks are just a normal brick turned 90 degrees & the longer brick is placed normally. This is because the brick wall has 2 layers of bricks so every other course they will lay out the bricks turned 90 degrees to structurally tie the wall together.
I am afraid you're mistaken. Please check the pictures about this project on archdaily website and you will get the idea how it's made: www.archdaily.com/785923/crystal-houses-mvrdv/5717988fe58ece9e0b00011f-crystal-houses-mvrdv-photo?next_project=no
what @studio22a34 meant was that the conventional brick bonding only uses one set of brick dimensions, which is probably true for the actual bricks on top of the glass ones, the custom dimensions shown by the architects are probably only for the glass bricks (since they are unconventional)@@HowtoRhino of course this has no effect on your modelling since the aim is just to replicate the visual appearance.
Thank you for this great tutorial !! Very detailed and helped me out a lot 🙏🏼🙏🏼, I have a small problem I wonder if there is a solution to it; instead of using this on a plane wall, I would like to use it on a curved wall/ surface. Do you have any idea what I can change in the algorithm to make that happen ?
I have a problem to cut openings in a surface: I have a solid surface and a surface with openings. First I set this solid surface and it works correctly till this moment when you start cutting openings…. What do I need to do?
You need to take the “Panel” and inside of it type: {0,2,…} Please make sure the data placed in the D input of the Split Tree is simplified (you can enable it on the right click of the input). Hope it helps.
Free How to Rhino Community 👉 www.skool.com/howtorhino
Rhino for Architects Course ✔ howtorhino.com/rhino-for-architects-course/
Extended Tutorial + Extra Project Files 👉 www.patreon.com/posts/49228239
CZcams Tutorial + Project Files 👉 www.patreon.com/posts/49229348
sometimes, the bricks are the same size just layed once on the long side and once on the shortside, and when placed on the long side two bricks are used so that the width is the same as a brick layed on the shortside, its cheaper than buying 2 different sets of bricks :)
This is great, thank you very much for the tutorial
Thanks Juan! Glad you're liked it :)
Thank you! That’s what I tried to google today 😄
You're welcome Tore! Perfect timing 😄 Thanks for checking us out.
At the beginning you say the normal brick is in 2 sizes (normal brick & double brick). I just want to clarify that it isn't a double brick, those smaller bricks are just a normal brick turned 90 degrees & the longer brick is placed normally. This is because the brick wall has 2 layers of bricks so every other course they will lay out the bricks turned 90 degrees to structurally tie the wall together.
I am afraid you're mistaken. Please check the pictures about this project on archdaily website and you will get the idea how it's made: www.archdaily.com/785923/crystal-houses-mvrdv/5717988fe58ece9e0b00011f-crystal-houses-mvrdv-photo?next_project=no
what @studio22a34 meant was that the conventional brick bonding only uses one set of brick dimensions, which is probably true for the actual bricks on top of the glass ones, the custom dimensions shown by the architects are probably only for the glass bricks (since they are unconventional)@@HowtoRhino of course this has no effect on your modelling since the aim is just to replicate the visual appearance.
Can I bring this into revit?
Thank you for this great tutorial !! Very detailed and helped me out a lot 🙏🏼🙏🏼, I have a small problem I wonder if there is a solution to it; instead of using this on a plane wall, I would like to use it on a curved wall/ surface. Do you have any idea what I can change in the algorithm to make that happen ?
Great work as always! Thanks for the tutorial. One simple question, do you use an app to take those screenshots and draw on top of them?
Thank you Alejandro!
We use the Lightshot app for Windows. It's very handy for sketching on top of screenshots.
If you were to render the individual bricks though, a single texture would look flat. How would you give it some natural variation?
I have a problem to cut openings in a surface:
I have a solid surface and a surface with openings. First I set this solid surface and it works correctly till this moment when you start cutting openings…. What do I need to do?
I've got the same problem. Where you able to figure it out?
Hey Artem, were you able to figure it out? im also facing similar issues here, cheers
How do you do the syntax part when u are doing the split tree for the contour lines?
You need to take the “Panel” and inside of it type: {0,2,…}
Please make sure the data placed in the D input of the Split Tree is simplified (you can enable it on the right click of the input). Hope it helps.
in your course you teach also grashopper? will it has subtitles in spanish??
You can see a lot of information here about the course howtorhino.com/rhino-for-architects-course/
It is in English, no subtitles :)
@@HowtoRhino the price for the pack?
@@luisfe7187 schedule a call on that page if you're interested and we'll walk you through the platform and share all the details on the call