Amazing! Process of Mixing Copper and Steel to Make a Damascus Knife.
Vložit
- čas přidán 21. 08. 2024
- Amazing! Process of Mixing Copper and Steel to Make a Damascus Knife.
👍🏻 Thank you so much for Watching my Videos
✅ All videos are produced free of charge for company promotion.
🎬 Contact us : holymaker148@gmail.com
🎥 Copyright(C) 2023. Holy Maker. all rights reserved.
🔎 Information (정보)
🔔 Knife in the video (영상 속 칼) : Cafe Pulmu 카페 풀무 (055-291-2886)
📢 Instagram (인스타그램) : instagram.com/mr.k4879/
📢 wep page (홈페이지) : m.blog.naver.com/PostList.naver?blogId=d909n990
✅ All videos are produced free of charge for company promotion.
✅ 모든 영상은 국내 기업 홍보를 위해 무료로 제작 됩니다.
🎬 Contact us(촬영 문의) : holymaker148@gmail.com
I'm not one to drop a like or dislike without giving a critique on a video like this, so I hope you take this to heart. Before anything, I came here from the short because I had some questions that this video answered. And please don't misunderstand, it is a beautiful blade, but it may not last long with use
A) Your blade is maybe a fraction as strong as it could be, so hopefully this is a decorative piece more than anything. While you stick welded the edges, you burned into the billets on at least one side and proceeded to belt-sand off the excess weld, but without a reference to where the actual metal was located. It may have been better to just spread a ton of flux between the layers, tack weld a few spots, and let the forge and power hammer take care of the bonding between the metals.
B) You wasted a lot of metal by shaping it with the plasma torch, especially when you also demonstrated that you understand how to draw and shape with forge tools.
C) This was double so when you started on the tang. You also may have weakened the blade where it meets the tang as the sharp corners create major stress points. You made them worse by keeping the top "step" of the hidden tang design above the handle.
D) Which brings me to how poor the tang as a whole is. By cutting it out with an angle grinder and then stick welding more to the length, you have almost assured that the tang WILL snap, even with all the epoxy(?) you poured into the over sized hole for it.
E) I can ignore the rest of issues for a display blade, but shaping the handle with the blade attached on a belt sander with a pair of latex dipped fabric gloves is asking for some trouble. Please protect your hands and that blade better. One slip could have screwed that blade up permanently or lost you a hand--it does not have to be sharp to remove a bone.
Всё это красиво на уровне концепции. А потом медь начнёт окисляться... .
Если че, Медь и Железо создают гальванопару, причем довольно-таки приличных разнозарядов, так что сплав начнет корродировать
до первой воды,классный буторброт
Tourist knife ! And for the ladies, chocolate/ice cream?
BEAUTIFUL............................
As a plumber this would make a great presentation knife .I luv the copper sandwich !
Well done sir
😎
Thanks😉
It's funny, as a retired plumber my first thought is steel and copper don't work well together.
@crankfastle8138 what , are you an Iron bigot? 😃
The metod is called mokume gane. I dislike plasma cutting, soldering handle, epoxi sticking. Reali for me this is beginer in blacksmithing. May be is good in finishing work of already forged blade.
Just from the videos of very skilled blacksmiths I've seen on CZcams, I would agree with you. He cut the shape of the blade instead of hammering it to compress it further. His plasma cutter can't even cut thru a thin piece of mixed metal.
@zackfowler8613 but he did "inlay"=same difference : the copper in the metal. May add a bit of softness to the overall blade I guess but if just for looks he could have pounded the design in & added copper later .. still way better than I can do ....for now. 🤞
Muito linda essa faca!!! 👏🏼👏🏼😉👍🏼
Truly amazing piece! Thanks for some much needed inspiration I needed :)
excellent craftmanship is rare to find in our mass produced World we live in
Мог бы и болгаркой (УШМ) отрезать
Господи, что это за ужас....
Зато красивое. Наверное... )
Es maravilloso amigo...
I have been a knife maker for over thirty years your blade work is outstanding your handle work sorry to say not so much but your blade craft is stellar.
I was going to say…. I’m not a smith but I’ve seen hundreds of videos of people making knives and thought the same thing about him welding the handle onto the blade. That just creates a weak spot…. But the blade is beautiful.
@@robertjohnston6976Whaat?
@@robertjohnston6976the part he welded on broke off before he was finished
Чи не спциолит. У нас на зонах такие вещи делают,что этому мастеру учится и учится.И все без навароченног инструмента,и в тихоря ,то б мусара не видели.
Думаю, что кроме эстетики, медь не придаёт никаких дополнительных, полезных свойств металлу.
Csodálatos munka!
Beautiful!!
😉👍
Wonderful skills.Terrific video. I wish that I liked the final product. Thank you for posting this.
Молодец
и для чего этот нож, для еды его нельзя использовать?
Una maravilla, original 💯👍⭐⭐⭐⭐⭐
Very cool blade !
😉👍
This is skill and art. I love it.
Thanks😉❤️
ダマスカスには見えませんが、これはこれで綺麗ですね。 ただ鉄と銅でイオン化傾向が違うので電蝕起こしそうで怖いですが大丈夫なのでしょうかね？
Bravo artigiano a mano gran coltello ci manca il fodero io lo farei che arrivava metà manico in cuoio marrone che tira al rosso buon lavoro 👍🤩🥷
😉👍❤️
Красота
Один вопрос: а нахрена ? Какой такой это дамаск...китайский ?
👏👏👏👏👏👏 No words
Sense of art, beautiful...
Tá aí um cara que sabe o que tá fazendo
Почему я не удивлюсь, когда этот пакет расслоится?
А х тебя з). А почему он расслоится?
@@Ivan_Sidorov потому что такая кузнечная сварка, без флюса, и т.д.... Да и полировка клинка- такое себе, на последних кадрах хорошо видно. Это не нож для работы, это чисто полочник.
@@user-dh5ul2ej8c ну нож из меди врятли для работы подойдёт. а если для полки то и пыхтеть над ним не стоит
@@Ivan_Sidorov ну, красиво сделать, пусть и для полки, тоже надо постараться.
@@user-dh5ul2ej8c а зачем дерьмо для полки?
I think you lost the handle you welded on earlier.
It's a cool idea , but because steel and copper are unlike metals this knife will separate. Next time use brass and braze them together and not only will it look great it'll be strong also.
😉👍
Esta equivocado...no se desarma en absoluto...en todo el mundo se hace...la técnica no es damasco...es cu mai
I thought the same thing but that's purely because of my plumbing background.
Медь ничуть не худший припой по сравнению с латынью, так что даже не стоит переживать что что то будет распадаться! У латуни температура плавления ниже чем у меди так что можно просто не попасть в интервал ковки стали!!!
たえず微弱電流が流れる異金属接触効果で腐食が起きそうな気がしますが、どうなんでしょう？
Would love to have a dagger like that.
Very good job !!
Jó gépekkel ez egy taknyolás.Ív hegesztés 0 a plazma vágás gány . Az eredmény lenyűgöző.
What about corrosion? Copper and steel do have different electric potentials. Normally the steel would suffer losses at the border to the copper.
A very reasonable remark. This blade should not see any moisture or water, and definitely not any salt .
мокуме- гане... и коррозии там и прочее.На выходе странный пакет..Декорация.
That's good question about galvanic corrosion.
But galvanic corrosion occur continuously an electrolytes.
So If this knife doesn't dip in the water, no problem
Дамаска здесь ни разу небыло...
👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
🙇♂️❤️
Медь окислится через месяц и ?..
nice looking knife , but it's not a true Damascus knife as Damascus blades come from folding and from what i saw in the video the blade was not folded, putting 3 layers of steel and 2 layers of copper and welding them does not equal a Damascus knife
👍👍
You're right. You are also flat out ignoring the skill that it takes to not just melt the copper and drive it out of the laminate. But, hey. You're right. Nit pick away.
Nitpick away? Nit pick away? The blade is perfect.
@ierc6532 that's why nit picking about what type of laminate it is is pointless. Sarcasm is a thing.
Damascus and pattern welded steel are two different things Wootz steel which is a crucible steel is the closest modern version
凄い職人が作ってるのかと思ったら、単なる鉄工所が見よう見まねで作ってるだけの動画だったｗ
どうせだったら、もっと重ねて作れば綺麗だったのにね
Чисто сувенирный,для дела шляпа
A beautiful knife and truly a custom made cutting blade!
Thanks😉👍
Nice looking knife. The steel and the copper really complement each other when they are that polished. Using your hand to block the flash while welding will not save your eyes, please wear a proper shield. I would like to see something like this again but with a much higher layer count - maybe 50-100 layers.
Joan Margarit... Mallorca. Knives
Was this the first time making a knife?
Binnen de eerste 30 seconden dacht ik al "wat mooi!"
😉👍
Magnífica!!! Parabéns!! Curitiba, Paraná - Brasil
Sanwich blade.
Great work dude. 😄😄
Thanks🙇♂️
Ficou linda.
Parabéns
😉👍
I'm trying to figure out how to forge weld plastic into a steel - copper isn't nearly soft enough...
Amigo, la tecnica no es de acero damasco, se llama cu-mai
홀리메이커 화이팅!!!!
감사합니다^^
Sir, is it strong,.? I'm impressed
Of course it's weaker than a steel-only knife, but it's strong enough to use because it's been heat treated enough.
How do you stop delamination?
👍👍👍👍
приваривать хвостовик - плохая идея. сажать рукоять на эпоксидный клей без механического крепления - идея тоже паршивая
А больше ничего не смутило? ) Это ножик чисто на полочку положить и фапать на него изредка. )
ОЧЕНЬ КРАСИВО
Que maravilha de faca
😉❤️
😂 дамасск??? Теперь я знаю, что такое дамасск😅
예쁘기는 한데 갈바닉 현상은 어떻게 해결하셨나요?
It would be a great honor to own one of these pieces. What would it cost to buy one and have it shipped to Canada?
Лезвие ножа конечно красивое но есть ли толк от этого ?
Нет клнечно
Есть, нож стоит на шкафу или висит на ковре и радует глаз, твёрдость Дамаска это твёрдость самой мягкой входящей в пакет стали, а тут это медь. Это красивая сувенирка, соответственно в придании сувенирке лишней красоты толк есть. 😂
다마스커스의 특징은 강함 아닙니까?
무두질도 거의 없고...
그냥 예쁘기만 할 갓 같습니다.
용접에서 놀랫고 플라즈마 절단기 숙련도에서 놀랬다가 단조에서 또 놀라고.... 담금에서 또....놀라움에 연속이네요
진짜 본업은 아니신거죠??
원래 육군 부사관으로 근무하시다가 대장장이 기술을 배우셨다고 합니다.
지금도 항상 배우시는 마음으로 수련 중이시구요. 😉👍
둘이 짜고 치냐? 쇠쟁이들 지나가다 웃다 자빠지겠네..차라리 안녹이고 불조절 잘하시네요 하면 그게 더 믿음이 가네..무슨 용접에 놀라고 프라즈마에 놀래ㅋㅋ
@@Holy_Maker죄송합니다 좋은 의미에 놀라움은 아니었어요 정말 듣도 보도못한 장면이어서...
@@auftk5418제가 쓴게 다시 보니 헷갈리만하네요
좋은 의미에 놀라움이 아니었어요😅
@@Holy_Maker 오리지날 단조를 수십년 한 사람입니다 ㅎㅎ
걍 좀더 숙달 하셔서 영상 올리세요
산소절단 막봉용접 단조 집게질 서툴게 보여서 제품에 신뢰가 안갈꺼 같아요
ليس دمشقيا لكنه عمل ممتاز المرجو أن تعملها بالفولاذ الدمشقي سيكون مذهلا
콘크리트못으로다마스칼만들수있을까요?
🤔 충분히 가능하지 않을까 생각합니다
Pois é usando equipamentos super sofisticados pra fazer coisas elementares... É muito exibicionismo sem qualquer mostra de arte... Que pena e mais uma vergonha aos realmente alquimistas japoneses aos quais tenho a mais alta admiração.
Дааа, всякие тиски видел, но что бы с приваренными губками?
И сварка у комрада явно не конёк.
болгарка без кожуха, сварка без маски, защитные очки отсутствуют. техника безопасности? не, не слышал про такую!
Это путь самурая. )
Зачем губки к тискам приварены? Это для чего?
Все деньши ушли на лазерный маркиратор. Тиски пришлось уж какие были.
Herrliche Arbeit, das würde ich auch gerne können, aber dahin ist es noch ein langer Weg.
Ну бумажку резать это не показатель, я тут самый дешевый кухонный ножик наточил и также резал и не А4 который плотнее, а обычную тонкую газету.
вот если бы ты им проволоку разрубил это другое дело, а так.... .
Чисто декоративная поделка. Медь и сталь в одном клинке слоями - это нонсенс. Назвать такое дамаском - это кощунство и оскорбление настоящих мастеров. 👎👎👎
It is very nice to look at, but is there any real advantages of having copper layer in a steel knife?
I personally doubt it can make a durable blade but rather a "unique" finish.
My father is a blacksmith and i have never heard of him using copper in Damascus. Just Nickel,Carbon steel of different kinds and Borax as flux. Then Hydrochloric acid to etch it. He never used butane oven though, just "Bituminous coal" and Coke.
Maybe a tiny bit of copper can add to the finish but copper is to soft to use in steel for knives, Period 🙂
銅可以做為鋼層連接層，只要確保鋼材中心是鋼，硬度應該不是問題，銅質較軟也能吸受衝擊
No
Aqui no Brasil 🇧🇷 conheço como aço San Mai
Не вложено частички мастера туда, бездушное отношение к делу.
The audio was just fine at 2.5% volume.
Cantik benar itu Fisau tembaaga,¢$
any long term corrosion problems with the dissimilar metals?
Congratulations! He created a knife shaped battery! Lol! There is a galvanic current created by dissimilar metals. I believe with enough time the copper “veneer” on the blade will peel off from the steel creating a fish gill effect.
Also he could have created a knife shape during forging and avoid the oxyacetylene cutting completely
Buen trabajo,en el comienzo no se vio que usaste voraz por qué?
Hola que acero usó ?
Я раньше тоже так метал варил без маски, и теперь у меня зрение -1,25 и -1,50...
What is the purpose of the copper strips built into the blade?
Beautiful
Beautiful knife
Shit, not knife. This is shit.
Это мастер сувениров а не ножей
И где тут дамаск? 😂
в названии ролика )))
даа, бумагу резать, самое то ))
Один вопрос , НАХРЕНА¿???????¿?¿¿
how many hours you need for this ?
綺麗だけど、錆びそう
겹치지도 않는데 무슨 다마스커스….?
創意還可以，但技術感覺不算很優，刀尖用切割就算了，刀根還是用切的...最詬病的是...刀根長度不足外接.....比賽就算了..示範影片還是這樣子...
Frankenstein knife🧌