One more thing to check is if you are using a OSD, in the settings pick the same format that your camera uses (NTSC or PAL). Otherwise thats another cause for no video.
Project Blue Falcon alright let's say for instance that I have no idea what my working camera and VTX are using. So in a case like that how would I know? I know these two work together but I don't know which one either of them are. and from what I've heard from you before the ones that say that they're ntsc and pal switchable, or whatever, are sometimes not switchable at all.
JC was a genius at pretty much everything.He just had the knowledge to fix any drone and 6 yrs later I am still learning from his extensive video collection..Rest in peace my man!✈️🙏✌️
It gave me an idea. Although it was correctly soldered to the board there was tiny tiny spillage of solder which was causing short circuit and there was not enough power for camera. Thanks man.
Yes, you're so right: I unfortunately sinned against the god of mini-quads when not ordering spare arms when they were available for few bucks. Fortunately your repair videos inspired me to order a cheap part of carbon which I was able to mill (correct translation to english?) my spare arm with my cheap proxxon drill and a 3mm mill out of it. - Otherwise I would have been lost because the spare arms seem to be still not available worldwide. Never sinn against the god of the mini-quads ;-) - Always buy the spare parts while they are available.
I'm having problems with my tinygo. I get the OSD in my goggles, I've replaced the VTX and got a new camera, but when I plug in the camera I get no connection at all. No lights or sounds or even controller connection and cannot even get the black screen with the OSD. When the new camera is plugged in I can't even connect to Betaflight but all my wires are correct. Is this a flight controller problem?
+ Project Blue Falcon I've got a Tyrant S 215 and can't get the FPV system working.Here's the list. - Diatone SP2 V2 VTX - Replaced with same - Some Crappy Diatone FPV cam - Replaced with Runcam Swift Mini - Channels are all the same on VTX and Attitude V3s - Tested with other quads and the image comes through fine. - Tested continuity and seems like power is running through PDB to Cam and VTX without issue - It's not a black screen so cam should be fine >>>>>>>>>>>>>>JUST STATIC
hi, i tried everything you showed here, but it didnt work, i dont know whether its my camera because it doesnt have a 5volt connector, but only video, gnd and VCC. My fpv ca,mera is the foxeer razer micro Thank you
Thank you so much I realized there were 2 spots to plug in my camera cable I was like why tf isn’t it working then I saw ur problem. Thanks so much man
I had the same problem with a brand new Runcam a couple of days ago, the screen is black, but I can see the camera's osd... it says 'Runcam' and it shows the timer and the camera voltage... but no image... I sent the info to Runcam and they are sending me a new inner board...
Thanks JC. Any chance you could do a video on repairing the OSD chip. I've had two go out and feel like there is a better way than replacing the FC each time. Thanks again...
I have a similar problem. I get the video signal extremely clear about 2-5 feet. I walk away a little bit and the video signal goes hay wire. Can you please help me.
was wondering whether anyone would be able to help me! i have no video through my goggles when everything seems wired correctly. troubleshooting like in this video i solder the camera and vtx wires together and i now have video. Do i need to replace the entire flight controller??
I have the same issue but start after a crash last weekend..... I switch the Camera still not working than the transmiter but still not working ... I see a black Image with very tinny light spot ... When I go to Camera menu I can see with no probleme the menu but no Image .... Only thing i have more is L-C Power Filter-1.7A to power up transmiter and camera ... I will remove it to see ... Do you have some other sugestions ?
Thanks for the insight to your troubleshooting approach! Sounds logical and methodical...! I'm sure it slipped your mind to give Ray the credit for that lens cap tip!!!
Please check cables first with multimeter. Following your advice would in a worst case scenario destroy two cameras.... More importantly: I'd like to add that many cameras that accept 5V and up do not work if voltage is just below 5V. Typically a 5V BEC drops to 4,8V when it powers several devices and for many cameras (like HS1177) it is not enough. The result is exactly the same as in this troubleshoot: OSD with black video.
Example: Matek PDB 5V out ---> HS1177 and TBS Unify PRO. This will not work because of voltage sag. Unify works fine but camera will not start because voltage is at 4,8V
I'm running the Omnibus as well, the standard F3 version. My OSD was working fine when running BF 3.1.6, but after flashing to 3.1.7, it stopped working. Still getting video tho. Any idea what the problem is? Would my OSD chip go bad just from a simple upgrade of firmware?
Did you check in the betaflight configuration tab if after the upgrade the OSD option is still turned on? - If yes, try to uncheck it, save and reboot, then turn it on again, save and reboot and see if it may work again. Maybe this helps? I also have the F3 omnibus and flashing to 3.1.7 did nothing to the board and I can't imagine how that could technically happen.
Hi Jc. I'm going insane. Iv got a betaflight f3 and tbs unify. I can see osd in goggles but no camera. Just black screen. Iv put a vid on my channel with as much info as I can. Please can u take a look. And help me pleeeaaase. Ps camera is on auto on betaflight osd menu. Iv tried both
One more thing to check is if you are using a OSD, in the settings pick the same format that your camera uses (NTSC or PAL). Otherwise thats another cause for no video.
Project Blue Falcon alright let's say for instance that I have no idea what my working camera and VTX are using. So in a case like that how would I know? I know these two work together but I don't know which one either of them are. and from what I've heard from you before the ones that say that they're ntsc and pal switchable, or whatever, are sometimes not switchable at all.
It should not be black then, Video lines and noise...
Chris Meyer what shouldn't be black?
I am sorry, I was generally replying to troubleshooting a NTSC, PAL mix up. If those two get mixed up, video is not just Black.
Chris Meyer no, thank you. I was just asking you to clarify without actually saying that, I guess. and again, thank you.
Still teaching us up in heaven. You will not be forgotten ❤️
JC was a genius at pretty much everything.He just had the knowledge to fix any drone and 6 yrs later I am still learning from his extensive video collection..Rest in peace my man!✈️🙏✌️
RIP JC! Thanks for your videos and knowledge. You'll be missed.
Michael Neil What happened to him? :(
@@UrbanSleepersOfficial He passed away in a motorcycle accident.
Michael Neil Wow when did this happen? That’s so sad
@@UrbanSleepersOfficial June 29, 2017. You can search "JC rip project blue falcon" for more info. Pepper FPV is his brother.
Michael Neil Thank you Michael, I appreciate it
Miss ya buddy. If you were still around you would be one of the top Dogs of fpv CZcamsrs.
Still helping me years later. Thanks JC and RIP ❤️
Yeah, at least it wasn't the lens cap... JC, thanks for keeping it raw!
JC -the OG of fpv
Keep sharing even the littlest stuff. It's why we watch JC. Keep doing exactly what you do and congrates on the upcoming show.
Literally helping me in September 2021.
It gave me an idea. Although it was correctly soldered to the board there was tiny tiny spillage of solder which was causing short circuit and there was not enough power for camera.
Thanks man.
I make stupid mistakes all the time too. Nothing to feel bad about. It's just nice to know I'm not the only one!
The delightful thing about standards is that there are so many to choose from.
RIP my bro your flying high now 🛸🕊️🛸
Yes, you're so right: I unfortunately sinned against the god of mini-quads when not ordering spare arms when they were available for few bucks.
Fortunately your repair videos inspired me to order a cheap part of carbon which I was able to mill (correct translation to english?) my spare arm with my cheap proxxon drill and a 3mm mill out of it. - Otherwise I would have been lost because the spare arms seem to be still not available worldwide.
Never sinn against the god of the mini-quads ;-) - Always buy the spare parts while they are available.
Really appreciate this video. I just went back to runcam because of a camera issue.
How could something like that just happen? The quad looks used, he did not mention that he had just added a new wire?!
Lens cap.
JC is definitely right about spares. If you can afford 'em get em.
I'm having problems with my tinygo. I get the OSD in my goggles, I've replaced the VTX and got a new camera, but when I plug in the camera I get no connection at all. No lights or sounds or even controller connection and cannot even get the black screen with the OSD. When the new camera is plugged in I can't even connect to Betaflight but all my wires are correct. Is this a flight controller problem?
+ Project Blue Falcon
I've got a Tyrant S 215 and can't get the FPV system working.Here's the list.
- Diatone SP2 V2 VTX - Replaced with same
- Some Crappy Diatone FPV cam - Replaced with Runcam Swift Mini
- Channels are all the same on VTX and Attitude V3s
- Tested with other quads and the image comes through fine.
- Tested continuity and seems like power is running through PDB to Cam and VTX without issue
- It's not a black screen so cam should be fine
>>>>>>>>>>>>>>JUST STATIC
Thanks, your Video helped me today to fix my Video Signal.
hi, i tried everything you showed here, but it didnt work, i dont know whether its my camera because it doesnt have a 5volt connector, but only video, gnd and VCC. My fpv ca,mera is the foxeer razer micro
Thank you
I did this exact same thing with my build earlier this month. 3am and slightly drunk. Everything worked out in the end.
Thank you so much I realized there were 2 spots to plug in my camera cable I was like why tf isn’t it working then I saw ur problem. Thanks so much man
simple problem, but it's very important.
Honest to God. Rip. I never met you but I wish I had. Thank you
PERFECT TIMING
Hi RC, Did you also have your spare camera checked on 'short circuit'? This was also wrongly connected.
Hehe, I was half expecting a blank CZcams screen with just you talking about troubleshooting ;-)
I fucking love you JC
I had the same problem with a brand new Runcam a couple of days ago, the screen is black, but I can see the camera's osd... it says 'Runcam' and it shows the timer and the camera voltage... but no image... I sent the info to Runcam and they are sending me a new inner board...
Thanks JC. Any chance you could do a video on repairing the OSD chip. I've had two go out and feel like there is a better way than replacing the FC each time. Thanks again...
Will do
This if he hasentdone it this is a will not do RIP Jc
😢
I have a similar problem. I get the video signal extremely clear about 2-5 feet. I walk away a little bit and the video signal goes hay wire. Can you please help me.
alright this may be a dumb question. But what do you mean? Or how so? because they have to match right?
how do you figure out whether or not your camera or your VTX is pal or ntsc if you've had it for a while and it doesn't say it anywhere on either one?
I just try both
was wondering whether anyone would be able to help me! i have no video through my goggles when everything seems wired correctly. troubleshooting like in this video i solder the camera and vtx wires together and i now have video. Do i need to replace the entire flight controller??
I always have an issues with static when I do punch outs. I have tried several different VTX's, filters and so on. Just can figure it out.
I have the same issue but start after a crash last weekend..... I switch the Camera still not working than the transmiter but still not working ... I see a black Image with very tinny light spot ... When I go to Camera menu I can see with no probleme the menu but no Image .... Only thing i have more is L-C Power Filter-1.7A to power up transmiter and camera ... I will remove it to see ... Do you have some other sugestions ?
JC I have video but sometimes the omnibus osd goes away after I first turn it on. Any Ideas
even with no osd if you have most times if you have grey picture the cam is broken if the vtx is sending signal it would be white noise
Thanks for the insight to your troubleshooting approach! Sounds logical and methodical...! I'm sure it slipped your mind to give Ray the credit for that lens cap tip!!!
I just soldered the power and gnd wires of the camera on the pdb instead of the fc. It fixed it
I did the same thing with mixing up power and video but on the BF F3, not in the cam. Luckily everything seemed to be ok after.
I changed the vtx channel on my goggles now thinking shows up but snow
still got grey screen damit.
Please check cables first with multimeter. Following your advice would in a worst case scenario destroy two cameras.... More importantly: I'd like to add that many cameras that accept 5V and up do not work if voltage is just below 5V. Typically a 5V BEC drops to 4,8V when it powers several devices and for many cameras (like HS1177) it is not enough. The result is exactly the same as in this troubleshoot: OSD with black video.
Example: Matek PDB 5V out ---> HS1177 and TBS Unify PRO. This will not work because of voltage sag. Unify works fine but camera will not start because voltage is at 4,8V
Thanks so much for this video. I had the exact same problem and you helped me figure it out!
Good video thank you! Even if there was a rookie mistake. You're doing a good job thank you.
I'm running the Omnibus as well, the standard F3 version. My OSD was working fine when running BF 3.1.6, but after flashing to 3.1.7, it stopped working. Still getting video tho. Any idea what the problem is?
Would my OSD chip go bad just from a simple upgrade of firmware?
Did you check in the betaflight configuration tab if after the upgrade the OSD option is still turned on? - If yes, try to uncheck it, save and reboot, then turn it on again, save and reboot and see if it may work again.
Maybe this helps?
I also have the F3 omnibus and flashing to 3.1.7 did nothing to the board and I can't imagine how that could technically happen.
Henri Schomäcker
Yeah I'm not too sure why the osd stopped working as well, but I'll try what you just mentioned. Thanx manx
Ah, and btw: Also check the OSD tab if there's everything turned on that you like to see on the osd.
Hi Jc. I'm going insane. Iv got a betaflight f3 and tbs unify. I can see osd in goggles but no camera. Just black screen. Iv put a vid on my channel with as much info as I can. Please can u take a look. And help me pleeeaaase. Ps camera is on auto on betaflight osd menu. Iv tried both
I'm having same problem black screen. I took a hard hit and video went black but still get OSD.
did you figure it out? i have the same problem. hard hit now i have black screen. wiring is correct.
I'm getting no osd
Awesome video great help
Lol, I did the with. VTX the other day as was rushing to beat the sun going down, only trouble was it fried the VTX 😖
This didn't help, still having black screen.
God bless him and everyone else :)
Nice fix
he he Take the cap off the camera! lol
I forget all the time haha
Thanks/ Good effort / .
why is erveryone posting RIP?
is he dead?
yes, he died in a motorcycle accident.
you should wear eyeliner
Rip