Vevor Hat Heatpress
Vložit
- čas přidán 21. 08. 2024
- In this video I demonstrate how to Apply an appliqué patch to a hat blank using a Vevor Hatpress.
This press works great. In this demo you will see that I pressed twice for the one patch. That was simply because I missed one top corner when I aligned the hat on the press. This is a good unit and will do the job as well as other small transfer jobs.
#vevor #vevorheatpress #vevorhatpress #hatpress #heatpress
amzn.to/3lKRRzq
Awesome video. I couldn’t find the tutorial on the actual Vevor page so this really helped. I appreciate you doing this.
You are welcome, I do not work for this company but would be glad to answer any questions you might have if I can.
Thanks for the comment.
Thank you so much for your video…your temperature settings for the caps saved me from messing up my second cap. ❤❤❤
You are welcome! I am glad the video was helpful. Good luck!
Hi I know it's been years since this video but di you have a video showing how to change it from Celsius to Fahrenheit ? Thank u
Absolutely, I just made a quick video for you : czcams.com/users/shortsmhDz-R9CArI?si=HvlXBnioUAxX9NB5
Hi can you do a video on putting temp and time and how you put it on farihet because mines is staying on Celsius I need to put it on farihet thank you great video
I would still like a video to see how to change the type of temperature from Fahrenheit to Celsius and vice versa.
Awesome video!! Straight to the point! Where did you get your designed patches?
Thank you! I get my patches mostly from Amazon currently. I am always looking for better deals. I buy them as a “lot”. I get the best per patch deal that ways. Thanks again!
How do you not get a crease near the sewing of the 6 panel hat? Everytime I get a crease no matter how much cushion I add.
Hello, have you tried decreasing the amount of pressure using the tension adjustment on the top plate? A lot of of experimentation unfortunately . I use a silicone sheet and also a pose of thin cardboard has been helpful to me. Good luck.
Thanks for the vid…. How do you get rid of the box-shaped imprint left from the press, it sort of squared the front of the hat off and made a crease along the top where the heat press ended. If you’re trying to possibly sell the hats, what is the best way to avoid or get rid of that? Thank you!
Hello, great question. Although I’m not a professional my suggestions would be…
1. Make sure you don’t have the the heat plate too tight. Maybe experiment by loosening the tension some.
2. Make sure the heat plate is not too hot so you do not overheat and burn the hat.
3. Make sure you have the inside rim of the hat folded out so that it is not in the press when applying the patch or appliqué.
4. Lastly, I use Teflon sheets between the heat press and my hat to avoid burn and impression of the plate
amzn.to/3Zm4wvB
I hope these suggestions help.
Cheers!
I just got this heat press and I’m getting creases on hats, especially the foam trucker style. Any advice on how to avoid this? I lessened the pressure, but was worried about it adhering.
Hello, yeah, the creases can be an issue. Especially with the foam based trucker style hats. You need to be extra careful with how much heat you use so you don’t scorch or melt the hat. I have not used this style of hat for that reason. However you might try using Teflon sheets on top and see if you get better results. I use them on my regular hats at it seemed to decrease the amount of indentation made by the press. Here’s a link: amzn.to/3qJKhuU
Good luck. Let me know if it works for you.
Do you always use it? How many hat did you press approximatly?
I use it quite frequently. Mostly for hats but I also use in to apply patches to small items like cross body bags and more. I would say I have made at least 100 or more items with this press so far.
I just buy one, i don't wait for the delevery. Thank you for your answer and sorry for the bad english. I'm french.
You are welcome! I hope you have great success with your press!
Does the crease go away
Such a useful vid. Did you buy any other add ons besides the Teflon sheet and heat tape? I’m buying this machine for dtf onto structured hats. I seen someone say something about a rubber add on for the bottom platen. Can you share a link? ❤
Hello! Thanks for watching and for the comment. Teflon sheets and heat tape is all. I of course purchased some hat blanks. Here’s the link for the press.
Hat Heat Press: amzn.to/3Pvr9vk
Teflon Sheets: amzn.to/3NteIxl
Heat Tape: amzn.to/3Pv8sI7
Here are some Hat Blanks: amzn.to/3JxV2ae
I hope this helps!
Quincy
Hi ! I bought the same one but the setup indicator the « out » button keeps flashing red with a « click » sound do you have any idea of what the problem could be ?
Cheers
Would this heat work just as well with leather patches?
I don’t see why not. A leather appliqué should work the same. This press has adjustable heat and pressure adjustment so…. I think it would work well. ( disclaimer)- I am not affiliated with the manufacturer or distributor’s of this press. I am a consumer who just uses this press.
What do you use to build it because when I press leave dents
I use a teflon sheet. If that does not help, try reducing the amount of pressure on the press by loosening the tension knob on top. I have also used a small piece of thin card stock. I hope this helps.
Where did you get the spring clamp that holds the hat in place? I have the Vevor p8100, and it didn't come with that part.
Hello! That’s a pretty important part in order to stabilize the hat. The press I purchased had the part attached when I got it. If it’s the same press, I would suggest contacting the manufacturer and tell them. They will most likely send you a new one at no charge. When I purchased mine the timer was glitchy so I complained, they sent me a new one right out. Good luck
I’m looking for custom made 3d patches but everything I find on Amazon it’s expensive like $12 each patch
Been trying to find out the name of that tape.. and could you tell me where they sale it
Sure thing, here is a link. amzn.to/3uVKtqx
The time doesn’t countdown, if you can help
Hello, sorry to hear your issue. I am not a representative of the company so I can only guess that there is a malfunction with your machine. You should try to contact the manufacturer of the hat pre and tell them of your issue. I have found that many times they are very helpful. Sorry.
Sorry guys but the vevor machine I bought is a total piece of crap! Heat temperature was going all over the place and not constant at all. Ruined several hats before I checked the temperature with a temp gun. Temp would rise and fall by 35 to 40 degrees the whole time it was on. I was not aware of it until I ruined a few hats. Tech support said that was normal. That was my answer and solution. Awful way to lose money. Threw it in the trash. They would not honor my warranty. Done. Best be careful when buying this machine or at least check it out before your 30 days runs out.
Yeah, it can be a bit of a crapshoot when buying heat presses that are lower in cost. The only way around it is to buy the more expensive models from places like Pro World. This model in in the video has worked well for me. I’ve used it for hats and other small areas on shirt pockets and and stuff. However, I purchased mine from amazon and the first one had a faulty control unit. I actually contacted the manufacturer, not amazon. They sent me a brand new one and it’s been great! Sorry for your experience.
Where can I buy the 3d patches ?
Hey! Please can you let me know if trucker caps work with this? I’ve seen mixed reviews
Hello, the spring tensioner helps pull the cap tightly against the heat bed. However, it’s important to make sure your heat settings are not too hot for the materials in the cap. Nylon is probably more sensitive and could be damaged with too much heat. That being said, this heat press is durable and works as it should and expected. I for one have had a few failures as I learned. I do not work or represent Vevor in any way but do have two of their presses and recommend them.
@@seemycapeproductions7833 thank you for that, it’s always a difficult one deciding which to get!
@@jamiecooper8585 you’re welcome! Good luck! I hope you find the right solution for your projects. I have a link in the description to this particular press if you decide to get this one. Also, would appreciate a like and subscribe. I will be doing more videos for these kinds of products soon! Thanks again.
What is the sheet that you put over the patch and where did you buy it?
Hello, I think you are referring to the Teflon Sheet. I place it between the hat or garment and the heat press plate to avoid any scorch marks that can be caused from the heat plate. I got them on Amazon.
I hope that answers your question.
@@seemycapeproductions7833 Thank You, I purchased the same silicone sheet. Did you take the adhesive backing off? if so, does it stick the the hat?
@@beachedgolfdid you already get it! I accidentally posted the wrong link. So sorry. Can you cancel not return
@@beachedgolf I am really sorry that I told you the wrong thing. I was in a hurry and posted the reply with out double checking:-/ here is the correct link…
amzn.to/3yi4SXA
I feel really bad, sorry
Please tell me why my heat plate wiggles I have the same press😫
I am not a dealer for this unit but. I am wondering if this is a new problem? Have you had the unit for a while and been using it? One thought is that the screw down tightener is not tight enough.
@@seemycapeproductions7833No just got it a month ago only use 3x
@@HustleStrongworld My suggestion would be to check all the bolts on the head to see if they can be tightened. One other thought is…. When I bought mine, it had an issue with the timer. I contacted the manufacturer and they sent me a brand new unit and allowed me to keep the original at no cost. They were very helpful.
@@seemycapeproductions7833 Thanks will do
@@HustleStrongworld Good Luck!