Video není dostupné.
Omlouváme se.
The BEST Way to Braze Copper Pipes
Vložit
- čas přidán 29. 03. 2023
- Looking for the best tool to braze copper pipes? Look no further! In this video, we'll take a look at the Turbo Torch and Rosebud torch set-ups and see how they compare. We'll also learn about the different types of brazing rods and tips available, so you can find the perfect set-up for your needs.
▶️ Recommended Playlist: • Playlist
✅LET’S STAY IN TOUCH: stan.store/Rog...
🔔 Subscribe for more AWESOME plumbing videos: / @rogerwakefield
⭐️ Become a Member TODAY: / rogerwakefield
________________________________________________________________________________________________
⏰ Chapters:
________________________________________________________________________________________________
✅ For business inquiries contact me at contact@rogerwakefield.com
________________________________________________________________________________________________
🔴 Links:
Check Out My Merch! - roger-wakefiel...
My Free Mini-Course- bit.ly/rogersfr...
My Networking Secrets That Grew My Plumbing Business FAST - bit.ly/rogersfr...
PlumbStudy- plumbstudy.thi...
My Recommended Plumbing Study Guide -amzn.to/2RgYEn5
________________________________________________________________________________________________
Thanks for watching! I'm Roger Wakefield, The Expert Plumber, and welcome to my channel. On this channel, it's ALL about plumbing. We play games, we experiment, and we have FUN here, talking and learning about all things plumbing!
____________________________________________________________________________
🎥 Gear We Use:
Coolest Clock Ever - amzn.to/31CjLkW
Audio Equipment
a.co/d/ffOocT0
a.co/d/9QWI1Ja
a.co/d/feepPWg
a.co/d/6Hdim5i
a.co/d/5sOqj4A
Cameras
a.co/d/4V542Bs
a.co/d/bUHdV4l
a.co/d/701Eg8A
a.co/d/febCgKf
a.co/d/dCQe8vL
Lenses
a.co/d/iChKFjm
a.co/d/05lWGDf
a.co/d/4lnIlcE
Tripods/Stabilizers
a.co/d/eWDPEwY
a.co/d/1QW1sB4
a.co/d/dolXDUo
Lighting
a.co/d/eerARwX
a.co/d/hMK6rOM
*NOTE: This description contains affiliate links that allow you to find the items mentioned in this video and support the channel at NO COST TO YOU. While this channel may earn minimal sums when the viewer uses the links, the viewer is in NO WAY obligated to use these links. Thank you for your support!
The hardest part about brazing is getting over overthinking it. Soon as you get past the fear of messing something up it’s smooth sailing at least that’s how it went for me 😂
That's the truth!
You are correct. As soon as that butter flows you know it 😜
Do you braze in HVAC? Cause that's where I get worried. Even with wet rag brazing so close to components that can't get hot.
Passed my journeyman's exam this week, thanks for your help with that, and all the teaching you do here!
Great job! Keep it up and never stop learning!
My fucking boy congrats my fellow brother
Everyone's a critic Roger. As long as the joint doesn't leak that's really all that matters at the end of the day
i like turbo torch because of the size of the flame. normally doing it in tight spot and stuff in front and behind the pipe i am fixing . great video
Not a fan of that oxidizing flame, but I guess if your in a hurry. I've always found that it's much easier to repair leaks, do touch-ups and recap joints when your pipe and fittings aren't cooked to holy hell. As a shipyard pipefitter, appearance and cleanliness is important too.
Those braze joints look good. Everyone has their own preference on what to use. I liked a #2 tip for braze and air/ace tip for soldering. I didn't have a need for a rosebud tip. Thanks for sharing.
Right on, thanks for sharing Brad
Literally started to learn brazing today in my HVAC apprenticeship class. What are the odds of that? 😬
The mustache knows all
@@RogerWakefield 😱
Roger in Europe that’s called cupotechnic.Brazing is with brass rods and a powder flux.We used the silver solder rods for that but your right it’s a lifetime job.
i like to get the pipe and the fitting glowing red hot then add the filler rod. quick and easy it lets you get all your work done with plenty of time for screwing off.
I only use the rose bud for 2in and up pipe sizes. The turbo torch takes too long. For brazing smaller pipe 1/2 to 1in I'll use a welding tip, MAP gas, or a Tutbo torch.
What type of silver are you using? How do you feel about staybrite?
i use a mini oxygen acetylene rig to braze and med gas,and fitting should be glowing while you push your unbent brazing rod into cup for full pen and yes you purge it ,its more of a weld than soldier and i clean fittings too that packing oil will mess up a joint in heartbeat
Love the out takes lmao
Does brazing get into the joint? Can you cut it in half and see how far the filler goes in?
Turbo torche #1
What is the difference between brazing and soldering?
The temperature needed to melt the rod.
From what I can tell, brazing last longer and is better against vibrations...
You can braze into existing lines without a fitting
Pressure it can withstand
A solder joint is actually a stronger joint
Heat resistance. Solder melts at a much lower temperature than brazing rod
@@destinylags6863 just curious how solder is stronger than brazing? I would never want to solder a joint inside a big ac unit it just wouldn't feel safe to me.
"I don't know that it does." That's a special kind of integrity, there.
I have a leak from the sink drain under a raised foundation. Any videos or advice?
braze it
Nice
Looks good from my house
Love to hear it
When are you going to do an update for the following legislation, do you think 4 year mater will be lower to 1 year? Plz let us know 🙏
It no brainer for amateur like me to get turbotorch because even expert like you still struggling with rose torch. Also I do refrigeration repair in the restaurant and turning on/off oxytorch really piss off many staffers.
I use a 14 tip on anything up to 2” but maybe it’s the camera but none of those joints
You know that safe has some heavy artillery inside it
sure does
@@RogerWakefield hell yeah!
Rosebud on bigger pipe usually anything 2” and above
Turbo torch is usually good up until about 2 inch pipe after that it gets very difficult and that’s where a rosebud would be easier
And don’t forget we’re hearing protection with these they are very loud
📢 You got that right 📢
Gotta break out that Oxy-Acetylene torch for the bigger HVAC lines.
I see you haven’t been introduced to the A-36 tip
You can't cool a joint fast. You have to wait for it to cool down on it own. Think about it as putting water on ice.... the ice has fractures in them when you do that, so will your solder or brazing.
My welds are fucked up and i do up to 2 inch hard copper but ive never had a LEAK
Great job!
Teach me Rodger
Aight lets go
I am more concern about the flames around the table.
Table is good 💪
In my opinion that is way too much flame on the oxy rosebud. Just a waste of gas and harder to control cherry red heat.
Roger you ever worked a job where it was so far away from home your accommodation and transport was paid?
I'm no plumber but
Why not use nuts and the rings
Fire inside a house gives me the creeps
points to non existent video tag at end lol
Fixed it...thanks for pointing that out 👍
@@RogerWakefield no problem!
U roger are a texas jcat what we call u girls in california
you failed right off rip and your union and med gas trained🙄 whats first thing they tell you dont do ? Do not bend your brazzing rod especially on med gas
Roger aren't you the one who used almost a whole rod on a 3/4 joint.. wouldn't be calling you an expert, probably a hack at best
My joints don’t have leaks 🤷🏻♂️
Same here just so happens that I only use a small amount cause thats all a brazed joint needs
Pretty low of you to call Roger a hack. Also I want proof of your amazing brazing skills on a CZcams video. Show us how amazing you are! I highly doubt you even have a torch just a typical CZcams bully.
Relax pretty boy, been a pipe fitter and a welder for way to long, and before that a plumber. So typically I can definitely call out a hack when I see one. And ps at this point a torch is just an extension of my body as far as I'm concerned
Why are people still brazing? Why not just pex it
Braze is better than pex 🤷🏻♂️
Depends on the type of building and fire code/plumbing code in your area, brazed soft copper can be buried for water in my area but pex can't have any fittings in it. At a couple hundred bucks per 4" fitting tee drilling and brazing gets economical really quickly too.
Because all medical gas must be brazed? Wait until you hear about refrigeration 🤣