How To Install a Ground Source Heat Pump
VloĆŸit
- Äas pĆidĂĄn 26. 08. 2024
- Sponsored by Worcester Bosch Heat Pumps
đ www.worcester-...
What are the basic workings of a heat pump?
A heat pump is a relatively new technology in the UK although they are widely used in Scandinavia and many parts of Europe where there is an abundance of renewably sourced electricity.
A heat pump takes energy from outside and transfers it into heat to be circulated around a heating and hot water system.
A heat pump uses electricity to run the components of a heat pump, principally a fan, compressor and circulating pumps to transfer the energy from the heat source into the heat sink or heating system.
Greenstore LECP heat pumps overview
Worcester Bosch Greenstore ground source heat pumps provide economical, low carbon energy, enabling you to meet all of the heating and hot water requirements of your home from one renewable source.
Available in two versions, the system version has been designed for use with a G3 approved Greenstore solar-ready cylinder for the production of hot water, whilst a G3 approved Combination model includes a built-in 185-litre cylinder.
Find out more: www.worcester-...
=============================================
#GroundSourceHeatPumps #HeatPumps #Sponsored
đ Skill Builder Link Tree: linktr.ee/skil...
đ Tell us what you like: skill-builder.u...
đȘ Ask Skill Builder: skill-builder.u...
đŁ Facebook: / skillbuilderchannel
đ· Instagram: / skill_builder
đ As an Amazon Associate, we earn from qualifying purchases
đŹ All videos: www.youtube.co...
⟠Out of respect to our channel sponsors and the wide variety of people who watch our videos, we'll remove comments that do not follow common standards of politeness and decency.
Good to see your posh son is getting involved Roger đđœ
Nice to to see your young brother getting involved. Not a rant in sight. I reckon all that copper piping has made you bitter and twistedđ€Łđ€Ł. Only joking your a top man Rodger.đ
It's young Roger again with his telephone voice!!
I've been looking at renewables for years and I totally agree with you Roger. Don't let them get you down.
We had a GSHP installed in Sept 21 and are located in the Hudson Valley NY USA. It is a 5 ton vertical closed loop system with two bore holes each 88 meters deep. On Jan 16 at 4A ET temp outside was -1F or -18.33 Celsius. The water coming in was at 42.5F or 5.833C and going out was 38.9F or 4.39C. The return air was 65.8F or 18.7C the supply air was 86.5F or 30.3C. The temp was set to 68F or 20C in the house.
Do you mind giving us a ballpark of the price and how difficult it was to have installed?
â@@redmysterium After all rebates and the Fed Tax Credit it comes in at $21,800 USD. From start to turning it on took about four days for the drilling and two weeks to complete the installation. That included removing an air source heat pump and an oil furnace.
@@chrismaxny4066 Thanks so much.
@@chrismaxny4066 just so you know, just got two estimates, 5 ton ground source closed loop, radiant flooring and heating in a 3100 square foot house- $145,000.00! Not joking.
Our quote was $40,375 and after a discount for cash payment, an incentive from Central Hudson (electric company) and a 26% Federal Tax Credit the price was $21,315.70. The check we wrote to Dandelion was $28,805 as the fed tax credit wasn't received until we filed taxes. We have forced air heating and cooling and a 1800 sq ft home but that still is a huge difference!
Nice to see your getting your son involved Roger
He's been to a detox yoga retreat, cucumber on the eyes.......
@@vic6820
His son yeah ? đ
Article on our local TV tonight about an idea I had years ago - drilling into old flooded mines and running the pipes in there . Literally millions of gallons of water at 20c all year round. We have apparently many thousands of such mines in the UK!
Yes good idea but if too many people extract heat from one source it wll freeze. Maybe we need to put heat pumps at the poles.
@@SkillBuilder why should we give heat pumps only to Polish people?
#DadJoke
But seriously folks, maybe not @skill builder. The water in the would continue to circulate heat from the rock and water and earth in the mine.
If you are seriously interested in mine water heat visit Newcastle Gateshead 6MW district heating scheme and UKGEOS Glasgow research facility .
next up on skill builder : "How to install your domestic nuclear reactor"
never get planning lol
I donât think youâll have the proper license. Lol
The only sensible answer mc sarcasm ! Iâm amazed at the politeness of replies typ brits ,
Should be a united FO lol
One of the main issues with heat pumps is how these systems actually perform in real life, so many reviews and analysis are at the stage of being fitted when everything seems great. As this was done some time ago it would be very interesting to go back and see how well it performed over time, speaking to the owners and looking at running costs over time. That would be far more useful than hearing how wonderful things are before it gets switched on!
We will try and do a follow up
From my experience they use a LOT of electric, plus the install cost, never recoupe that cost ever
@@Ben-in6qh Could it be that your home isn't insulated well enough?
@@Ben-in6qh they do. But they use less than electric radiators do for the same amount of heat.
@@Ben-in6qh I do not think that they use a lot of electricity...it just a pump...also the ground always has a constant temperature...not like the air in winter time
Just to note. There are still those who are skeptical about global warming and this is mainly due to not understanding what the term actually means. Most people do not equate cold temperatures to 'warming', so;
As greenhouse gases build up in the atmosphere, that humanity has produced and which has been happening for several centuries, light from the Sun is trapped in these gas molecules which causes the bonds between the atoms to vibrate. This vibration produces heat. A warmer atmosphere equates to a more turbulent atmosphere. A more turbulent atmosphere results in more extremes of all kinds of weather. Hot, cold, rain, snow, storms and other atmospheric and climatic phenomena of all kinds.
I saw this video years ago and downloaded it as it was so interesting. Iâm guessing Itâs a shame you feel the need to bring it back because people are hounding you with regards to your recent comments on air source. Which I totally agree with. Thanks for the education once more đ
We brought this video back because it discusses ground source as opposed to air source. The simple facts are that most homes could not have ground source so the main focus of the government is air source which is not as efficient. Neither of these system will give you the same output as a gas boiler. Just for the record, I do not feel hounded in the slightest, I enjoy the debate and the video has had a a lot of views so I am happy.
@@SkillBuilder fair enough đ
This feels like it was filmed in the 80s!
If people are confused about how the ground contains heat, remember it's only cold relative to our bodies. Relative to the liquid refrigerant, the ground is warm as it's boiling point will be well below 0°C
You could also say it contains heat relative to outside at ground level.
I served my time on an electricity board and three months of it was spent with Prestcold in Oxford. Their advice on these systems was unless you have a river at the bottom of your garden forget it.
I was keen on a GSHP system about 18 years ago and got a specialist company in for a quote.
ÂŁ12k for a Scandinavian system if I dug 3x50m trenches 1 m deep and 1m wide for the collector slinkies.
Our family is quite large and between us we cover most building trades and I had had my quite large house built 6 years previous so it was quite well insulated for that time. But no underfloor heating. The radiators were going to be changed for suitable ones fed from the oil fired boiler.
It suddenly occurred to me to ask what was the thermal resistivity ( conductance ) of the soil? They asked why was I asking!
I explained that as a young electrical engineer one of my first jobs was a 132 kv underground cable from a power station transformer station. The thermal resistance was important to take the heat away from the cable. If it was not good special backfill was needed. Perhaps today this is taken into account but 18 years ago the company I was dealing with did not consider the soil at all. My soil is very high in clay and flint and very unsuitable for that type of system. So the project didnât go ahead.
Perhaps there is some data today showing the COP change with soil type? My guess is with heavy clay you would struggle to get a COP of 2 at 5 degrees Cost
You are right. Soil type is important. But in sweden it does not really affect cop normally, but it affect how long piping that is required for the collector. Wet clay soil is the best, and sand the worst (if i dont remember wrong).
We almost never use this slinky style. I dont think it is efficient.
@@bsod5608
Unfortunately I think you have remembered wrong about the soil type.
There are a lot of variables in soil thermal conductivity including moisture content , compaction (air gaps), temperature of the soil, and of course type of soil.
According to Oklahoma State University the conductivity for quartz (sand types) is the best at 8.8, clay is 3, and organic matter is 0.3, worst is air at .025
Because of the variables it is better to measure the actual conductivity on site.
I expect you may be right about slinky collectors. However collecting heat from as much volume of soil as you can must surely be better when you are running 24/7 in winter?
I have been getting a few cold calls over recent weeks about heatpumps and government grants etc. For the first time one of the callers actually admitted clay soils could be a problem.
GSHP is infinitely better than ASHP in terms of cold weather performance , noise etc. If I didn;t have a huge shading problem from trees (protection order so can't fell them) I would now go for a PV system with battery storage, thermal collection for hot water.
@@michaelviney3737 yeah, onsite test is best if it is possible to carry out. Dont know if it is expensive. The moisture content as you said is important, and clay tend to hold water better than sand. But really wet quartz sand is far superior to clay, that is right.
I looked up some reference values for differens soil types, and unfrozen [swedish] clay is typically 0,85 - 1,5 w/m, k. Frozen clay 2-2,8 w/m, k. Sand have a wider variety depending on its mineralorigin/water content, particle size, from 0.4 (dry) - 4. Pure quartz, as a rock is around 7.5 w/m, k. At least in my area, we never have pure quartz sand.
I dont think clay is unsuiteble for geothermal heat, it is very common here around. its just a question of sizing of the collector. A house with about 6kW heatpump would proably need around 400 - 600 m collector in sweden, due to long winter.
some more english reference-material.
www.geothermal-energy.org/pdf/IGAstandard/WGC/2010/2952.pdf
The slinky style may be more suitable for countries with a higher average outdoor temp than sweden. Local electric prices and cost for labour is probably changing how to optimize the system too. Its a basic investment cost vs operating cost.
airsouce vs groundsorce is all about air-temperature. Its a lower investment, so if you live in an area with fairly high airtemperature/short winters its genreally favorable with ASHP. In south of sweden its more favorable with ASHP, in the north GSHP is more favorable.
@@bsod5608 Thank you for your reply. You are fortunate in Sweden to have built suitable houses for relatively low water temperature systems. We in the UK mostly live in houses built for higher water temperatures and the cost of retrofitting is high. I used to look forward to my visits to Sweden to see ASEA when they were building the nuclear power plant in Sweden. Later they merged with the Swiss Company Brown Boveri with whom we had projects in the Middle East.
I'm afraid I do dislike ASHP having experienced them when living in Canada. But I expect they are correctly installed and operated in Sweden
Good Luck
Clay is ideal as it holds water which enhances the heat transfer
This was filmed before Roger's infamous "bump on the head" that turned him into a "bloke"
Key points works well with underfloor heating. Rads need to be larger than equivalent combi systems so factor the cost in .
Has a certain 90's vibe about it :)
so either roger has let his son do a video, or this video is so old that it just goes to show how far ahead of the curve roger was back in the 90's
whichever one it is, it's certainly an eye opener
It's a video from the 90s he just re uploaded for some reason. He has been wasting time talking with heat-geek lately, probably something to do with that.
@@cuckingfunt9353 well I saw his heat pump rant and I think this makes a good case for why the quick fix ones won't work
@@cuckingfunt9353 that's the 00s not the 90s
Is this the same Roger but after his anger management counselling session?đđ
Roger shall grow not old, as we that watch the videos grow old;
Age shall not weary him, nor the years condemn.
At the plugging of the channel, and the urging to subscribe,
We will remember him...
But not like this đ€Ł
Brilliant
Thank you! Looks like those systems are for the higher echelons. Would love to see an affordable one.
There is no cheap ground source option
@@SkillBuilder DIY
What a brilliant solution.
Bury some plastic in the ground, fill your house with plastic crap to insulate it enough to work. Planet saved!
Blooming el Roger. I thought the couple of beers was playing tricks on my eyes and hearing đ
Hope them heat geeks see this đ
They saw it ages ago. I think they agree with me on almost everything. Heat pumps in well insulated buildings work but they are still no match for a boiler.
Your ahead of the game but quite a few years by the looks of things. Luv your show. Keep on top and keep publishing because itâs people like you who the future really take advice and learn from. It goes s long way Thanks.
Iâm a very experienced tiler/bathroom fitter if you ever want to come to shoot any video clips.
Except nowdays all he is doing is slagging them off. Whatever gets the most ad revenue
Tricky
The fact that I am willing to tell the truth about air source is not a commercial decision. We could get loads of ads from heat pump manufacturers. Ground source is impractical and too expensive for most homes. Air source works with underfloor heating and high levels of insulation. If that is too nuanced for you then sorry.
@@SkillBuilder it works in other situations too. But in my opinion, you have an agenda aside from the ad revenue here. You are quite right it doesn't work everywhere, but I disagree with the headlines you are chasing discrediting the technology.
@@SkillBuilder Roger come on, you know that's not true, air source heat pumps can work in older buildings as Heat Geek recently showed.
@@patrickwheeler2646 he knows it's not true but it doesn't suit his agenda (Daily Fail)
Huge amount of space required for all the associated equipment, great for large houses but not for most people and especially for those who live in flats
Didn't see one worth having 20 years ago, and even now wearing glasses I still can see one worth having.
If global warming statistics and estimates turn out to be correct by 2030 the average winter tempreture will be -15, heat pumps won't be able to rise to the compensated required heat.
Lovely pipework on show there
Excellent video. The amount of disruption really comes across. To get to zero emissions we need to use all technologies available. The government needs to properly support these schemes to help householders overcome the disruption barrier.
Word!
Adds to total gdp debt, adds to more inflation, if you can't afford it then that's it
Excellent video, keep up the good work with the heat pumps!!
The deeper you drill, the warmer the ground is, and the extracted heat is then classed as geothermal. So people like me who live in small houses on small plots in cold, dull damp areas of the UK could only dig deep rather than wide.
You'd have to a long way to get more heat
Kilometres for geo and metres for ground source (This for UK with some tiny exceptions).
@@normanboyes4983 So where is the cut-off depth between sun-warmed ground and earth-core-warmed ground (on average in the UK)? Is there a level where it would be pointless installing a circulation system perhaps?
@@KendalSmithy over a kilometre
I didn't know ground source heat pumps could de-age you, might get one đ€
Looking good. You must have spent Christmas at a health resort. And taking elocution lessons đđ
Although this was one year ago, it still amazes me how many new builds are not taking advantage of this technology. especially thermal and solar panels on roofs as well as ground-source heat pumps. Near where I live there is a large solar farm taking up valuable agricultural land. So my question is two-fold why do we not mandate in the building regs sola and thermal heat and electric capture. I am not talking about this feeding back into the network, but using it on an individual basis. Or even a small community basis. In the same way, some villages are clubbing together for broadband internet as the big companies are trying to fleece small communities or just to gather government grants only serving the shareholders. We have seen what happened to the water industry mentioning no names.
Arh!! yes I remember the 70's.
Perfect video
Worcester Bosch providing Heat Pumps, is like a steak house providing vegan options.
Worcester Bosch are in the heating business.
@@SkillBuilder .... not the eating business
how many years would it take to break even on the cost of that? sounds good but not very realistic for your average Joe.
He said above that the system in the vid cost ÂŁ30,000. Zero chance the average joe like me will have that lying around so it's really only for people who need to heat their pool.
What a palaver. The lengths we have to go to so we can squeeze more people on to the planet.
Fantastic mate
Roger looks young after holidays
Regards
Faruk
One of the easiest ways to transfer heat from ground sources is with ground water if there is a sufficient supply the earth readily gives up it's stored heat and the cold return can be put back just as easily. Heating companies seem to steer customers away from this type as it cost a lot less. Cheers.
Roger! You have gotten younger! Waw!
dang, they put return bends on the compact collectors? in the states they would lay out the pipe in a coil fashion, no hard 90s
very informative , thank you
Like a young David Attenborough đ
Any chance of some ball-park costings Roger? I live in a 4 bedroom detached metal framed house, so can't use cavity wall insulation. I'm sceptical of the benefits claimed for these systems versus my existing gas boiler/radiator & cylinder set-up.
I'd be looking to apply exterior installation instead then - best not to lose heat in the first place than try and warm the air around the house. With power costs spiking at the moment, running the heat pump will also cost more.
There is nothing whatsoever to gain over your gas boiler. This job would cost you ÂŁ30,000 or more depending on size.
Dont bother, air to air heat pump and combi boiler combination is way to go
Well if the damn USA stop trying to start wars in Ukraine and let Nord Stream 2 start operating then gas will be the cheapest option by far
Don't blame USA you moron. The eu is to blame for the Ukraine problem. So I guess you don't give a fig about the thousands of dead Ukrainians. You are hypocritical, ill -informed, greedy and cynical
Thanks
Thanks, English Willem Defoe!
Willem Dafoe?
Great video Roger! Agree with you 100%.Great advice
It seems really stupid to put the forward pipe and return just next to each other and insulate them.
In sweden we dig 2 trenches about 1 m apart, and put forward in 1 and return in the other, and skip the insulation. We only insulate them the very last meter or 2 from the house.
That is a better idea but not always possible. I would get as much separation as possible
It's amazing how well these systems apparently work in much colder climates than the UK, I do wonder why.
My problem with ground source heat pumps or indeed air source is their over reliance on electronics to boost their so called electrical efficiency rating
Simple would be better ( old style direct switching rather than inverter driven)
After too many years to mention I have found that modern air conditioning systems ( which Heat pumps basically are) are as fragile as F1 cars against earlier types 1980s
They will be expensive to repair as not a plumbers repair job so new training will be needed or the normal cowboys will be in
Any problem and I bet the first thing the engineer says will be that replacing the unit will be cheaper
It will certainly be easier ( and more profitable) for him
All the electronics are made in China, the units change every 5 minutes and nothing is compatible. Asides from the boards there are lots of other electronics dotted around, MOSFETS' mounted on heatsinks capacitors mounted in motors, loads to go wrong. Even if you go with one of the big manufacturers you will be no better off, parts will become obsolete and the whole unit will need to be replaced. Since the new outdoor unit will no longer be compatible with the indoor system, indoor unit replacement and re connection will be required.
One big cluster fuck every 5-10 years.
@@cuckingfunt9353 Or just go with a Chinese Made System for 1/3 of the Price that has no fancy Inverter Controll and just let it run in steady states. That is my Plan. Everything else will be done via a regular Boiler. I fully agree with your statement. Just go as simple as it can be. My last Gas Boiler lastet almost 30 years, the one what replaced that old buity will be gone in latest 15 years.
It's the rain that takes heat into the ground, mostly. Little bit comes up.
Most heat comes down into the near surface crust (solar).
Very interesting. Thank you : )
@Skillbuilder, you are the best on this easy explanation videos for beginners if not your in the top 2.
Shame there's a lot of cowboy still messing ordinary folk especially with key constructions trade job, e.g Plastering, roofing, etc it 2022 ffs there small in number though. Keep doing these video's.
So well spoken đ
nice videos. I've seen quite a few now. Many thanks and great work! One question please, would it be possible for an underfloor heating system to double as a ground-source energy supply for the water immersion tank?. everything would be inside the building, and installation on top of clay.
K
Thanks!
Thank you Rodney, we love dollars
What would be the cost of fitting a ground source system to a detached 4/5 bed house with concrete floor. Walls and roof well insulated, roof space gives us three loft spaces, one along each sides of the roof and a standard loft at the apex of the roof. These have multi layers of insulation and are floored with roof standard chipboard and the roof eaves are also filled with insulation material. We nave now a combi boiled (3 years old and very efficient), an independent 10kw log burner. Windows and doors are double glazed and in some cases triple glazed and in some cases double glazed with secondary glazing and in some cases triple glazed with secondary glazing. We have a modern front porch and a large conservatory. Rear garden is approx 80ft x 40ft narrowing to 28ft. Access to the garden is not a problem and there is considerable parking to the front, paver drive. I need an estimate fairly quickly!
Great idea in theory, but with a COP of four, assuming it manages that consistently, and present electric prices, natural gas is still cheaper (4p/kwh vs electric at 22p/cop of 4 = 5.5p/kwh)
If you have gas, stick with it.
For how long? Gas prices are soaring and the stated government policy will be to reduce the differential between gas and electric costs per kWh in order to encourage the production and use of electricity and via wind and solar to deliver the reduced carbon emissions targets.
The situation is particularly acute if you live off the gas grid. Since moving into a property 5 years ago, supplied by lpg tanker deliveries, the cost per litre has risen from 32p/l to 55p/l. It has never dropped in that time only plateaued for brief periods before rising again. I can't imagine this trend changing, only continuing.
@@WirelessGriff Do you seriously believe the 6x difference between gas and electric, that based on the expected wholesale price increases in April of circa 40%, which will undoubtedly be more like 50% when it hits the retail market, making the difference between electric and gas around 10x different are going to be blended into a single rate?
Furthermore, the wholesale rate increase expectation of 40% in April and a further 20pc in Sept are going to make such a colossal void between electric and natural gas, you've going to need devices with an impossible year round COP of 10+ to even compete on basic energy consumption. To say nothing of the capex of course..
Energy prices will change to the detriment of gas - it will be a political balancing exercise to achieve that. Currently the Green tariffs (25%) are applied to electricity and given the pledges at COP26 the logical first step is to remove from electric and apply to gas.
But - I am still installing a new gas boiler in May 2022.
Or just fit a gas boilder?
The SIZE of the damned equipment needed in the home is crazy
looks like a really cheap and simple system to buy and install , just need a semi detached country estate terraced house, about 2 mill in the bank , a utility room the size of an average council semi , a workforce of 30 blokes for 2 months, solar panels , some champagne and a party for the great unwashed at the end of the project and hey presto, the planet is saved
Don't forget all the pumps that could pump enough water to Africa during a drought. And the things that will absouloutly not have any issues for the next 12 months, until an army of maintenance engineers build an office down the road as part of the lifetime of repairs the system needs.
You guys are the poster children for đȘđŻđŠđłđ”đȘđą with the tagline of âLetâs just keep polluting - we know đ”đ©đąđ” works. Who gives a đ© about the mess we leave for the next people (our grandchildren) to clean up.â Just keep throwing your plastic bottles and other trash out your window; someone else will take care of it!
Sure, this may not be perfect and will require some maintenance, but you can say the same thing for fossil fuels. The difference is that this system has remarkably less aftertaste, if the pumps are run with renewable energy like solar.
Great but for the ordinary suburban house its going to be impractical and if installed, very expensive. For me with a back garden 50ft x 50ft max and front 25ft x 80ft I reckon it would have to be a borehole. Then you have to find space for hot water storage and all the equipment. Then all the radiators would have to be upsized. Lastly, how could I get the very hot baths and showers I like, current hot water temp 60c for 'topping up'. Then we have the rocketing price of electric even at 4-1 efficiency. So solar panels and a battery needed. So what are we looking at? ÂŁ30k plus?
Maybe going down the shops to buy a big coat and some thermals!
Good comment, we are looking at heated jackets in a couple of weeks time
I bet that's not a cheap install. Crikey what a bit of kit.
Looking very young mate !
I see Rogers younger brother is in on the act now. Fresh out of 6th form college I guess đđđ€Łđ€Ł
Thinking about GSHP system in our house as it has timber floors with a concrete sub base. Plus I have about 2 acres of garden and a large rear extension coming up.
Only disappointing bit of this video was, like others of similar nature, the cost is never mentioned. So we know it is too expensive and payback will take years.
lol Just what I was thinking!
From recent research and pricing (for projects), I saw that it's likely the second generation / occupants that will see a financial benefit. If you get someone else to do everything (trench dig, install, etc.) it's probably around ÂŁ30-40,000 but I very much welcome correction. Money is far better spent insulating first (just my opinion, but externally), before bringing in the heat.
What was the payback period on your car or iPhoneâŠâŠ..?
@@normanboyes4983 wants and needs are different
@@electronicsandradio3945 Itâs a good point apply economics to needs and spend like itâs going out of fashion on wants.
Hello very well presented but you have mellowed? We had several buildings on our land at the rear of the main house with a mixture of half metre rubble walls and brick cavity walls where the original outbuildings had been extended into five three bedroom houses. There was plenty of room for a horizontal loop system but the ultimate decision was one borehole per house.
This worked well but only because we were able to line the interiors with 6" insulation during modification and extension of the original structures.
It was deemed impossible to attempt to install a heat pump in the main house as the half metre rubble wall with normal interior wooden frame and plasterboard would have to be completely stripped and various options of foam/resin etc applied for insulation with an estimated cost of ÂŁ35/40k.
The five three bedroom modifications referred to cost on average ÂŁ20k incl 100metre deep boreholes, pump and insulation.
What spurred me to make this comment is viewing your original you tube critique highlighting the potential issues applying to grant aided heat pump installations was music to my ears as i agreed with every single comment you made and I was hoping someone would point to the pitfalls of heat pumps as well as the benefits.
I fear there are going to be many people living in what I believe are unsuitable dwellings for heat pump conversion especially in conurbations where gas boilers are commonly used and could be a very costly mistake both for the home owner and government policy.
Good luck with all your future videos and don't be frightened of telling the truth I see you been taking some criticism from the trade???
The wisdom of youth.
CoP of 4, or even more may well be delivered on average over the year, but in winter it will drop to 1 or less when system inefficiencies are taken into account.
ie In winter, running costs will be horrendous based as it is on prime electricity. Mind you, in summer you'll have heating and hot water galore đ
Another point, in Scotland. the sun doesn't shine every day. Well, not underneath clouds it doesn't
Would be very illuminating to know the cost of the installation and associated work.
Interesting project, doesn't look cheap and heaven help any homeowner who ends up with a self-taught Checkatrade plumber rummaging around in that plant room. Might be better in a country with better regulated tradespeople. I don't imply that they're all poor, just the ones who've been round my house.
I bet your an Engineer đ
@@markfox7207 Well done Sir, you're bang on. I am a retired mechanical engineer. Please don't hold that against me as no-one is perfectđ
Roger looks great, he must be using litres of moisturiser
Great vid but how long does it that to pay for itself
What happens to the trees ? They need co2 to live to make oxygen. What about subsidence?
can any one recommend a company in the UK to install ground source
all right if you are lucky enough to have a nice house like the one here, tough shit for the rest of us.
Was This Your Apprenticeship First Job Rodger đ€ đđ
Think I'll Keep My Twenty Year Old Gas Boiler đ„đ€
Nice Property đđ
I want me one of those ground source youth pumps đ
P.s who clobbered the corner of the house brickwork with the digger đ€Ł
massive house with its own paddock is hardly representative of the majority of uk housing stock.
How do these systems compare in the dead of winter, while the ground might still have a temp to extract would it be able to sufficiently heat the house with say under floor heating or would you need to boost the heat as you would with some solar systems
I lived in a house with a ground source heat pump a while back and it was always nice and warm. It was a big system though so probably cost a fortune. My guess is that a smaller system with a boost for the coldest weeks would be more economical.
ground keeps a near constant temperature.
How many years since this video was made?
This video is old now.
Now, with there decade plus more experience, roger should do a follow up video explaining, the positives and negatives of such a thing today.
Has this tech improved since you made that video over a decade ago?
We will do more on this in the near future.
HNY Roger - did you find the fountain of youth over Christmas? Where can I find it please?
In a modest 3 bed house what would be the minimum sized garden for this compact collector to work ? You would also need a rather big room inside for the heat pump and anything else.
What happened to the Roger we know and love, that ranted about heat pumpâs being noisy and inefficient and not worth the expense?
That roger stopped getting paid to shill for heat pump manufacturers.
Ground source versus air source. two different things and you may notice they didn't chuck out the boiler. This video actually reinforces everything I said about the foolishness of taking out gas boilers and putting in air source
@@SkillBuilder So do you prefer ground source over air source?
@@koffibanan3099 yes he sure does.
Thanks for your reply Roger. Much appreciated. One question though, does the ground pump require the noisy air conditioning type unit fixed to the building with the fan unit running through the night?
Not what youâd call a âminimally invasiveâ option is it?
No it could do with a bit of keyhole surgery
Roger (or anyone) can you recommend a good gas boiler for a two bed flat. Not sure I could sacrifice my kidsâ bedroom for a GSHP boiler room.
How much did this system cost?
I don't understand why it's necessary to insulate the lines going to and from the field. Why can't the supply and return be run on opposite sides of a 24" trench and serve as part of the system? Picking up heat along the way? It's essentially the same thing as linear pipes in the field.
This trench is narrow and runs along the side of a swimming pool. Not everyone has the room for a 24inch trench and even if you do it can freeze.
@@SkillBuilder So if you have room for a 24" trench and can bury it as deep as all the other lines, the supply lines should not be insulated and therefor figure positively in the heat calculations, correct...? Seems like this would be the preferred option.
Also, I know you have a bone to pick with air source heat pumps but a German engineer type fellow I've built stuff for for years over here in california is telling me Viessmann is coming out with a new model that is ridiculously efficient. Are you aware of this and, if so, what's your thinking? It sure would be a lot easier to go with that thing than doing all the digging. I've got plenty of area to work with but none of it is flat.
By the way, thanks for responding.
Just looking at this is must have cost an absolute fortune . Just a replacement oil boiler cost me ÂŁ6K
Yes a lot of money
Lol how chill was Roger back then?
still the same, don't take all that ranting seriously, it takes a while to crank me up to that speed.
How about just have wall mounted units for heating and cooling, boil the kettle to wash up and use an electric shower. No need for ground source at all if you don't mind not having hot water coming out of the taps...an air source digital scroll inverter is pretty efficient and you don't need to be a landowner to have one.
That looks like a 'Rich-Mans-Toy' or a 'Universal-Debt-Generator' to Me đ€šđ€
One big electric heater how do you get 8 degrees to 30 degrees and the cost is extortionate
Love your videos, have you thought about doing an ask the expert show monthly? I'm sure lots of people would be interested on you and your teams opinions.
You read our minds, It is coming soon and will be on Wednesday nights
If it weren't for the installation cost this is the smartest thing people could do. It actually works all year round. It takes little energy to change ground heat from whatever it is 60-64 degrees to 70 and it takes very little energy to just blow a fan across that 60-64 deg temp in the pipes and actually a thermostat because most of us don't want it that cool in the summer. *It's not too bad of a forward investment. The biggest hurdle you have to overcome with most people most of the time is what it costs today versus what its total cost is. I've figured some people only have 8 bit systems. So along comes 32 and 64 bit and there's just.. there's too much communication gap. Like if someone tells me if I believe on Christ then this I understand the whole picture but most people only got enough just to hang themselves and for whatever stupid reason most preacher's never tell enough to actually be useful.
Does the ground over time cool and progressively reduce the efficiency of the system?
Yes, it can happen very quickly and we have seen cases where the ground has frozen. You can see a potential problem where the pipes run alongside the swimming pool.
@@SkillBuilder Truth is the daughter of Time, Roger!
Ground temp to 2-3 m depth varies seasonally (quite slowly across most of uk). Daily solar gain builds up âheatâ , but heat is also being lost via evapotranspiration so there is quite a complex flow of heat in the shallow subsurface (esp if there is shallow groundwater too). GSHP systems are âsupposedâ to be engineered to factor in soil thermal conductivity (which controls how well the soil will absorb and transmit heat/cold. Conductivity is a function of soil type and moisture content - and these can change considerably with depth - as well as laterally not all soils are as uniform as the one that is this video). If the collector is not designed correctly (too shallow, too closely spaced), then the system can freeze the ground (simply dumping more âcoldâ than the soil can conduct away) the compact systems really do have to be designed carefully, slinkies - less so. The idea is to strike a balance over the year, during winter you extract heat from the ground, over the summer the ground recovers naturally via solar gain (if you run a reversible system for air conditioning, you can pump heat into the ground- which can cause plant distress as you desiccate it). Generally, shallow GSHP go in about 1m depth (checkout the video - are those folks super short? Walking along those trenches?). As a geologist (with some experience of GSHP in Europe) I think too many of these systems are still being installed far too shallow- installers use shallow trenches because of costs but also to avoid rules about shoring trench walls over 1.2m deep (trench support kit is costly). Thermal gain âsweet spotâ for many uk soils is closer to 2m depth not 1mâŠitâs all about balancing that heat exchange- for which you want a steady temperature that you can work with and deeper is more stable than shallow. If your system is too shallow you may get marginal benefits in spring as the first 0.5m of ground warms up quickly, but you also run the risk of freezing as winter sets in and the solar gain tails off (there is a time lag as well- so itâs complicated ). If your system is too shallow (or you mess up the conductivity calcs) you really are going to end up not getting the COP=4.
Not with a water well system.....much much MUCH less expensive.
I guess you would make your money back in about 30 years
I doubt that, it would need replacing by then
Wow!! That must have been hugely expensive and totally inappropriate for the majority of properties in the UK. I live in a two bedroom terraced house built around 1900 ( 2 or 3 bedroom Victorian terraced houses are very common to most UK towns and cities). Internal wall insulation wouldn't work and exterior at the front only any good if the whole row had it done. Would maybe work at the rear? As far as heat source for water and heating I'm kind of stuck with gas or electric both of which are becoming more expensive very quickly. My rear garden (yard) is a sun trap in the spring and summer so it's a shame there's not some way of capturing this heat and storing it insulated under the house for winter use. I've no idea how this could be done or the longevity of heat held in storage systems. Are there any case studies for UK terraced houses and methods to insulate and heat such properties?. Only other option I can think of is knock them all down and start again!
Treble
I agree with all you say and storing heat under ground won't work for that long. I think we need cheap energy, that should be our goal and there are lots of people working towards it.
You can buy ground mounted solar PV panels and storage batteries. That would help with the rising electric costs