3-Ton Engine Hoist With Upgrades | Building, Using, Full Review
Vložit
- čas přidán 4. 07. 2024
- My full review of the 3 ton American Forge & Foundry engine hoist along with several modifications I made.
0:00 Overview
3:10 Using Hoist
6:42 Before Mods, Complete Review
16:07 Performing Modifications
Here is a list of some of the stuff used on this hoist:
3" Pulley (6657N23 McMaster-carr)
Shim washers to center pulley (92141A102- McMaster-carr)
4" swivel casters (2523T14- McMaster-carr)
Winch (2600lb WLL Tyler Hand Winch)
M8 cage nuts for the boom (90955A103- McMaster-carr)
The swivel D-rings or whatever you call them that are mounted on the end of the boom I bought on Ebay. VERY hard to find. The listing called them "ADB Hoist Ring Bolt-On 880 lb Working Load Limit 180° Pivot M8 x 1.25 Thread"
Tags: Engine hoist Winch mod
Engine Hoist Mods
Engine hoist upgrades - Auta a dopravní prostředky
Being a diesel truck tech for over 40 years and a truck shop owner for 33 years now, I can tell you are a very seasoned tech who actually does the work. Your attention to the little details when explaining why you changed this or that can only really be understood by those who have actually done these things you are talking about and realize that what you have done to modify this, will actually help, in that exact situation you are trying to modify it for. For example, the plastic boxes motors and transmissions come in, unless you have never actually hooked a chain to one of those and tried to lift it out of the box, would you realize that the legs are too close together ( on most hoists) and you end up putting one side of the box up on the legs of the hoist. Excellent little point. The reversible hoist small detail about having to just push forward or back to go up or down. Unless you have never used a rachet type hoist or come-a long, would you know that tiny detail that is so important when trying to stab a engine. The hood insulation, the tilting of engine, the holding of engine in position, ratchet strap hooks for both sideways and front to back adjustment are all excellent details only seasoned techs will notice. Great job.
Thanks, I appreciate the kind words!
Just found your channel, very refreshing, well planned, well spoken, well presented. Proof that an intelligent hard working man can provide a great service for his customers and you seem to have plenty of work. I look forward to watching watching all your videos
That American Forge Hoist bears a striking resemblance to the old ExCell W1000 (2 ton) American made lift.
Yes it looks identical but I'm sure the 🇺🇸 model had much better welds!
G'day from West Australia😉
43yrs trade life as 3rd gen Automotive Engineer.
Just had to say the only good Engine hoist I ever had I built.
Everything currently on the market is junk.
Must be time to build another one. Annnd make sure it doesn't grow legs and run away like my original one did😊
Nice job buddy, thumbs up from me 👍👍
Hi T R. Love your well thought out modifications and fabrication skills applied to the stock engine hoist.
I can use these on my engine hoist (machine hoist, that's all I bought it for, lifting and moving machines).
I ain't an engine tech fan but enjoyed watching you modification methods. I like those HD casters as well. Cheers Tony
Perfect... Great Very Detailed Video !! Much Appreciated !! Thumbs Up all the way...
Badass!! Learn something from every video u post!!
Very nice mods. I'm going to install cast iron casters to drop the height of my hoist as I have had issues running into control arms & equipment. Plus my casters don't roll well. I'm also making the front two casters non-swivel. I can steer it from the rear we'll enough. Thinking about a winch...
I super enjoyed your quality work. I think the hand winch was such a good idea. Adds a lot of versatility to the cherry picker. I use an adjustable crane on on one of my racks. I have a pit that I usually use to pull engines, although I haven’t done one for awhile. The advantage of the pit is that u have full access to the underside of the car whilst lifting the engine out with a come along. I support the trans with a transmission jack that always stays in the pit.
Thanks for the compliment! And yeah the hand winch is now a mandatory accessory in my book.
Very well done! I’m going to do a custom build lift of my own design to be able to employ some of these concepts and modularity while also able to maintain a somewhat compact design. I’d also like to add an area to the rear to stack counterweights in order to lift much heavier loads and have thought a lot about a multi-stage boom section in order to gain some height. That would all essentially turn an engine lift into a mini crane…. Or possible death trap, but time will tell. 😂
Very clever .... good mods .... well done ...
Excellent video, thank you
Very good young man.
Dam them welds are amazing your work looks amazing also.
Hard to mess up with a Miller squirt gun!
Brilliant!
New subscriber!!
Nice job, how high can the end of the crane go up? I am thinking of buying this so I can lift Bridgeport Mill up and down. I am not sure if this is too small for me.
You are a GENIUS! It's crazy how such simple upgrades make a difference!
Have you considered changing the hoist wheels? Thank you.
Thanks but all the credit should go to the other CZcams channels that gave me this idea. Also, I did replace the front wheels in this video. The rear swivel casters I left alone.
@@TechnicianRed do you think the winch added a mechanical advantage? On my cherry-picker, I want to add most of what you've done. I, too, wish to make use easier and to get a better mechanical advantage. Somehow rig a block & tackle etc. I think I might be expecting too much from the lift. I use my lift to get equipment in and it of my truck. Most of the time, I'm alone doing this by myself.
Thanks again for your sharing your knowledge.
@@xFalconFixerthe winch would only add mechanical advantage with a pulley setup but your lifting speed would be cut in half at a minimum. The winch I have has plenty of power to do these light duty diesels and is still much quicker overall than using the hydraulic ram on the boom.
do you remember the lift truck model # that you removed the counterweight from and do you think a 2ton lift would remove it.
it will help me out a lot if you reply. THANKS
That top post bending can be cured with reinforcement before it bends.
Or adding a tube inside the boom arm, then drilling the inner tube to pin at the 2T mark. (2 pins, weight is on them)
The HF legs, remake them 90° from the back tube. This makes pallets fit inside the legs
And the winch, maybe welding a snatch block on top. Why redesign the wheel, and you'll get to keep the original hook
The original hook still works. I keep it hanging from the hoist at all times in case I need it. I switch over to the hook if I am lifting something over 1500lbs.
Great mods. Have you done any mods to remove a diesel our of a van?
No, I have seen only 1 van come into our shop in 2 years.
will that lift a isx cummins 15 litre out of a peterbuilt semi?
Not sure. I only work on light duty diesels and down.
I put an 8 ton pump on mine.