Drawing Machine Assembly and First Try
Vložit
- čas přidán 4. 02. 2017
- Complete Bill of Materials:
3dmake.club/articles/drawing-m...
Files and software:
3dmake.club/articles/drawing-m...
My build of Drawing Machine by cyul (www.thingiverse.com/thing:1514145) with some little changes.
Here is an assembly video.
I ordered all the electronic components, rods,bearings, etc on AliExpress
Linear Shafts 8mm*400mm - 2pcs - ali.pub/1xattp
Linear Shafts 8mm*320mm - 2pcs - ali.pub/1xatr6
Linear Shaft 6mm*200mm - 1pcs - ali.pub/1xax78
LM6UU Bearings - 2pcs - ali.pub/1xau1h
LM8UU Bearings - 8 pcs - ali.pub/1xatyr
16 Teeth 5mm Bore Timing Pulleys - 2 pcs - ali.pub/1xavsh
16 Teeth 3mm Bore Idler Pulleys - 1 pcs - ali.pub/1xawbj
No Teeth 16 3mm Bore Idler Pulleys - 4 pcs - ali.pub/1xawbj
GT2 Belt - 2m - ali.pub/1xaudq
Arduino + CNC Shield + A4988 Drivers - 1 pcs - ali.pub/1xaukc
Nema 17 Stepper Motors - 2 pcs - ali.pub/1xath9
28BYJ-48 12V Stepper Motor - 1 pcs - ali.pub/1xaupz
Wiring Kit - 1 pcs - ali.pub/1xauz4
Power Source 12V 4A - 1 pcs - ali.pub/1xav4r
M3 Bolts - ali.pub/1xasl6
M3 Nuts - ali.pub/1xasw2
Buy in local hardware store:
M10*400mm Threaded Rods - 2 pcs
M10 Nuts - 8 pcs
M3*8mm Bolts - 11 pcs
M3*20 Bolts - 10 pcs
M3*30 Bolts - 8 pcs
M3 Nuts - 22 pcs
Inkscape gcode output extenstion for this thing based on MakerBot Unicorn gcode Output Extension: rgho.st/6xLQH5WJv - Věda a technologie
I'm totally digging the music
thanks a lot sir for a complete guide about grbl modification. you are only one who tell this. thanks again
MATHIMATICS I ACTION , THANKYOU FOR SHARING THIS HOME MADE DRAWING MACHINE
классный станок, классный видос, классная музыка)
Теперь осталось сделать так, чтобы в штатив можно было и фрезер поставить, и выжигатель...
Very nice Drawing Machine, I am building one for me. Thank you for sharing.
which software would you use
what can I say magic the music and video well done and thanks
Built the same with just Rs.2500 including all the parts mine was laser cut, rods were salvaged from old printers and the steppers were also from old xerox machines... The acrylic used was 16mm, 10mm & 6mm.. 120kg for acrylic scrap, parts took around 14mins to cut on co2 laser CNC 14mins x Rs. 8 = Rs.112, steppers cost Rs.60 each minebea 1.7amp 1.8deg, cnc shield +arduino uno+pololu stepsticks driver=Rs.1200, linear bearing Rs.600...
make a tutorial
Khadim Ali where and how I can get it?
Please, could you provide the dxf files? Unfortunatelly, I don't have 3d printer, just a small cnc router.
AA . Khadam Ali bhai . I want to see this machine . Can I contact you or can I buy from any place . Plz ? SMS me 03227663131
Hey ! Any chance I could get access to your laser cut files ? I wanted to print them first, but I guess printing them with an old ultimaker could be difficult. I would really appreciate your help !(: Thank you!
Hello, good job on builing it, looks great, thinking about making a similar one. What plastic did you use for parts? How much money did you pay for printing more or less? Peace!
If I want to increase my plotting area, what should I do? Will increasing the shaft size only do the job or shall I need to modify the electronics and code also?
Mind blowing ideas....
Подскажите пожалуйста куда подключить серву и нужен ли драйвер Zоси на шилде (при использовании сервы)? Собрал как в видео, все заработало. Есть необходимость на Z поменять мотор на серву. Пробовал grbl файл для сервы - машинка не работает совсем.
thank you for the stuff.
what is the firmware you used to control the Z axis with the 28BYJ-48 12V Stepper Motor please?
Good project. Could you list the bolts, nuts and screws, etc.? Thank you.
Muito Top!!
really creative
Nice video. Wanted to see how the movement work, it looks like CoreXY.
Hello Konstantin Konstantinov, I have already built the cnc plotter but I can not control the pen rise and fall.
I do not know if it has to do with the gcode file created in inkscape. When I am printing the pen is always in the same position, it does not go up or down. Can you help me?
Very very very gooooooood !
Too awesome work dear...
Can we use same mechanism for 2axis hotwire CNC machine?
which inkscape plugin is being used to create the Gcode?
Hi, I want to know how I could get the whole package to put together and how much would it cost? Thank you .
I was so impressed with your build. That I also build 1 like this. But theFiles and software link is broken. If you could share the files please
How to wire the pen holder motor, because it has five connectors while the cnc shield has only four connectors for each stepper ?
Thank you for this great project.
Pen is controlled by a servo i guess
Hi Konstantin,
Great job, I like it.
I already build similar drawning machine, but have a problem with calibration xy axis.
Can you tell me please, how to set the working surface of the machine (via inkscape or by arduino?)
Thanks in advance.
Same problem with me...did you fix it?
I have just built one like this but the controls are 45 degrees off as the clock turns. Is there something GRBL or $$ that can be changed to fix this?
If I increase the length of each X axis and Y axis to 100mm, do I need to change the code and modify the software?
And where do they change?
i find amaizing what u did !!! And i want to make also one like u did, at the moment i study electronics and i think it will help me a lot. a detailed instruction i found also at the website adress that you provide in the description but i need to know if :
do i need a 3d printer ??
do i need linux ?
Very nice video ji
Потрясающая работа =)
Потрясающая музыка я хочу слушать ее
I like those Indian drums in the background. I use that those sounds meditate. I like the video. ThanQ
background music.
first I feel like it coming from outside of my house .
.............. turn it off ....listen to your own music ... why the bitching ....
What the fuck do you have with those who didn't like this shit music?
What is the length of the threaded shaft and what is the measurement that it can draw (ie, Draw a maximum larger border line measurement L X W) Please reply..,...
Hello, may I ask does this work with colour paintings? Thank you.
How do I change the surface of drawing area ? I want to build a drawing machine with an area of 100cm x 100cm .
can you send me link of software and program link
do you think it is worth using this project for a 3d printer?
how did you connect the 28byj to the shield? the 28byj have 5 wires i you need 4 for the shield.
Hi, can you put a drawing file for example square or rectangle, because i have probably connected the wrong motors.
How do you route the belts ?
vare nice
I want to know how belt was connected
Please explain
My cnc pen plotter is going on the wrong side. When it draws the picture, it is not in this direction, but it is moving to the left side. how to fix it? Is it a software problem?
You are genius
Hello, the page with the software information does not work, what is the name of the software you use?
Greetings from dubai!
I plan on making this same arm. Can you explain in detail how you connected the belt? Also can I use this same mechanism with longer rods to cover 40x40 cm paper?
Ohh okay got it. Just to clarify you are using just one single belt that runs through the arm right?
Also what is the reach of the arm in the video?
Super
thankz
New link for writing kit please
Wow, nothing like checking your final edit before uploading huh
Hello Konstantin Konstantinov, I have already built the cnc plotter but I can not control the pen rise and fall.
I do not know if it has to do with the gcode file created in inkscape (mac), or if it has to do with the program I use to print (cncjs - mac).
When I am printing the pen is always in the same position, it does not go up or down and gives the error id = 23.
Can you help me?
Hello again Konstantin Konstantinov, I do not use any command in gcode to control the Z axis. I simply load the gcode file that was generated in inkscape and say to print.
What is the correct way to do, and how to command the Z Axis?
ty
How did u assemble belt
dear konstantin. what did you insert on board shield before inserted a4988? thank you so much
at 12:40. you insert things. before a4988?glue gum or anything?
ok. thank you so much. you connect pin ms1, ms2, ms3 to vcc for 1/16 step? and we'll can use inkscape for gcode file?
oh yeah. i understood. thank you so much. i'll diy it with material from old scanner and printer. hi
Konstantin Konstantinov are the micro shunt jumpers necessary?
Hi there. I got little problem when i make a print it printing 45 degree angle why it’s happen?
Can i use longer screw shafts
For bigger drawings?
sir can you plz tell me that how did you mount that gt2 pulley..?
Hi, how do i modified the code so that it recognizes M3 and M5 commands?
i still dont get how you get 2 axis motion with both stepper on the x axis...:( didnt show the cable routing.
I've been designing my own and use the same belt system. I found this video which explains the motion: czcams.com/video/_nzxGOKhHSY/video.html
@@RJFeddeler thank you for the link and saving my day pal.
Sir ,Kindly make vedio on software installation n implementation .
Hi, how do you manage z axis movement!
Where must i the belt together ???
I make this machine but wen i rotate one motor the machine move in 2 direction
Hi, Konstantin Konstantinos, congratulations for the video. It's very useful.
Can you send me the link to the 3D part that supports the arduino. That it does not exist in the site where they are, another. Thank you
thank you Konstantin Konstantinos
how to wiring motor to cnc shield board, please master ?!
ty
Can someone help me?. Why have some change the code in 16:33 ??
What is the function when you change this ?
how to insert belt plzz explain properly
Can you just say what type of screws you are using. Type and dimensions please.
Hola, amigo como puedo adquirir ese producto. Por favor ayudame.
I tried to download the gcodecreate.zip but it said that it is a virus.
Can I get a safe download somewhere?
can i help you peeka? i installed it. and using it. not virus.
How can I connect to servo? which pin should I use?
how to insert belt explain properly
What is measured by the size of drawings of 3D objects?
This machine worked based on inkscape Android application or not..??
hi, thank for video is best :D
what you are using to open your .h files ? 16:36 ?
again hi :) this time it gives such an error can you help me what should i do? Error: Expected command letter
I would like to buy only the plastic parts, how can I do?
how to make plastic stage ,end 1, end2 ,pen holder and its procedure
hello sir when i move x+ it moves diagonally can you help me to solve the issues
What kind of 3d printer is this??
I would like to buy one but I have no idea what should I choose...
the malyan m150 doesn't look very promising to me... Witch one do you use?
I am looking right now at a Tevo Tarantula what do you think of it?
Good job , can you sent new link for your files.
Can you please share the software and firmware link. Link is dead
how much filament did it took?
В чем измеряется размер чертежей 3д обьектов?
can I get the STL files of these 3d prints
Do the parts have a 3D printer view
Just haw u connect the GT2 belt ?? plz answer
What are some of your minor changes?
dear konstatin. can your machine write a letter or create signature? is this axidraw machine?
so. how can i write a letter? or create signature. i use inkscape to make gcode. but i don't know how to make this machine can write line.
do you have facebook? we can add friend and chat together.
i use axidraw hatch fill extension tools
Can you share if there is a grbl download link?
good
can you provide 3d printing file? thank you very much🙏
Please anyone can help me ? I want to build same one, but bigger, were can I buy the staff please help me
I've been trying for 6 months now but the servant doesn't
I don't know what else to do!!
Thanks for your video i have 3 questions
1. you included in your order Linear Shaft 6mm*200mm - 1pcs and i didn't saw in your video
2. The Bore timing pulleys you wrote 16TB5 are they 16T 6W B5 or 16T 10W 5B
3. what is that Linear shaft at 15:02
The Linear shaft is cut two pieces 100mm x 2 , and this it at 15:02
Where I can buy it.
I followed all ur steps..in gcode sender.. i upload a gcode file.. it doesnt working..
Can it be used for writing?
Осталось собрать 3д принтер, есть видео?)
what its the name of this song? i like
Can u make a belt setup video
Which one did you use? 28BYJ-Stepper 5V or 12V?
Marcelo Oroquieta I wonna know too
dear 3Dmake
I have done all the things ...
except drawing....I tried same tux mono in A4...but it draws to small...even though I give your values....pls help me bro
Hi bro can you guide me, becaus e my machine moves on xy directoion when given signal for x direction only... Can you help me