Make note that the risistor wire can only go in one way, if you find that it's not going through, you have the red cap upside down. Tried this, 💯% worked. Thank you for the detailed instructions!
I have a question. I installed new led marker lights to my 18 jl wrangler sharia an re hooked my oracle halo light like it was before an now I have no blinkers but when I disconnect the oracle light my blinkers work. Will this work for that 😮
Please go ahead and give us a call at 314-205-3033 Monday-Friday 10 a.m.- 5 p.m. CST, or shoot us an email at contact@diodedynamics.com, and our in-house US service team would be happy to help you with that.
I have those signals look so good white lights but can’t wait to buy those again without resistors need it or already incorporated in the near future since one of the resistors failed after only 10 months!
I installed a Switchback bulbs and resistors on my 2019 Wrangler the drivers flashes faster than the passenger and the bulb-out warning light comes on for about 3 seconds on the dashboard before it goes out any ideas why?
Only worked for the left (green&black) the right side did not work, I found a wiring diagram that show the right front is brown/white and black can you confirm
The sensors do get pretty hot, but they will only do so when the blinker is on. We don't have an exact temperature, but we recommend they are mounted to a metal surface away from other wires.
Hello, great video, very instructional. I have a question, Which resistors (Value) are appropriate for a 2018 Jeep Renegade Altitude brake/Turn led 1156?, Thx
Our LED resistors work on all model brake and turn signal bulbs. You can find them in the link provided below depending on how many you need! www.diodedynamics.com/catalogsearch/result/?q=resistor
More than likely you just didn't make a solid connection with the turn signal power and ground. We would recommend re-doing those connections, and confirming those wire colors. If you are still having troubles, please shoot us an email at contact@diodedynamics.com and we can assist you from there!
I installed these with the resistors in one side (passenger) and then I decided to test them. Neither side hyper flashes. Any reason why the driver side isn’t hyper flashing (without the resistors)? I’m thinking about not installing the resistors in that side...
I have a 2018 Sahara Unlimited JL. I installed the switchback bulbs purchased through you, but they stay solid amber. Come to find out after doing more research, the switchback bulbs wont work on the Sahara JL model. Would these resistors solve this issue? (the issue being that the lights are amber and not white LED at all)
You will need to install resistors with these bulbs! Go ahead and shoot us an email to contact@diodedyanmics.com, and our service team will be happy to help you troubleshoot!
These worked to kill the hyper flash on my DD LED turn signals. I also bought the tail lights which I love. Can someone please tell me which wires I need to install the tail light resistors on? I can't find a JL tail light wire schematic yet and I'm too lazy to chase the correct wires myself. Anyone know which color wires I need? Thanks!
Hi Tony, thanks for your support!! Please go ahead and give us a call at 314-205-3033 Monday-Friday 9 a.m.- 5 p.m. CST, or shoot us an email at contact@diodedynamics.com, and our service team will be happy to help you with that!
Hey there! Please give us a call at 314-205-3033, Monday-Friday 9 a.m.- 5 p.m. CST, or shoot us an email at contact@diodedynamics.com and our service team can assist you!
Hi there! Please go ahead and give us a call at 314-205-3033 Monday-Friday 9 a.m.- 5 p.m. CST, or shoot us an email at contact@diodedynamics.com, and our service team will be happy to help you with any installation questions!
This does not work for Sahara Unlimited models, for there are two bulbs. If you install a switchback it will stay white and the other incandescent bulb is your blinker.
When installing these, it will be one resistor per blinking bulb, so the same idea applies to all makes and models. The resistor will need to be tapped into the turn signal power and ground.
What resistor did you use ? I swapped from sport fenders to rubicon fenders with leds . I now have rubicon leds and wiring harnesses. Will the wiring color still be the same ? Will resistors work for the factory led setup ?
Hi Dean! We appreciate the suggestion and will be sure to pass it along to our media team. In the meantime, please feel free to give us a call at 314-205-3033 Monday-Friday 9 a.m.- 5 p.m. CST, or shoot us an email at contact@diodedynamics.com if we can answer any installation questions!
If I don’t install the resistors, would it mess up the system, with the hyper flash ? Basically can install my LED lights without the resistors and be okay ?
Why in the hell don't these car manufactures go ahead and start installing all LED lighting on new vehicles being sold. They are cheap now, efficient and long lasting. Stop using it as an "upgrade option" to suck more money out of our asses.
Make note that the risistor wire can only go in one way, if you find that it's not going through, you have the red cap upside down. Tried this, 💯% worked. Thank you for the detailed instructions!
Thanks for the tip!
I have a question. I installed new led marker lights to my 18 jl wrangler sharia an re hooked my oracle halo light like it was before an now I have no blinkers but when I disconnect the oracle light my blinkers work. Will this work for that 😮
Please go ahead and give us a call at 314-205-3033 Monday-Friday 10 a.m.- 5 p.m. CST, or shoot us an email at contact@diodedynamics.com, and our in-house US service team would be happy to help you with that.
I have those signals look so good white lights but can’t wait to buy those again without resistors need it or already incorporated in the near future since one of the resistors failed after only 10 months!
We're sorry to hear one of those failed! If you contact us at contact@diodedynamics.com, we can look into replacing it for you!
I installed a Switchback bulbs and resistors on my 2019 Wrangler the drivers flashes faster than the passenger and the bulb-out warning light comes on for about 3 seconds on the dashboard before it goes out any ideas why?
Only worked for the left (green&black) the right side did not work, I found a wiring diagram that show the right front is brown/white and black can you confirm
Hey David!
Please reach out to us at contact@diodedynamics.com, or give us a call at 314-205-3033 M-F CST, and we'll look into this with you!
So it’s gonna hot only when the turn signal is on, but not while the led fender light DRL working right ?
Correct. They don't produce heat unless the turn signal is active.
How hot does the resistor get? I’m concerned about using the product overall because of that.
The sensors do get pretty hot, but they will only do so when the blinker is on. We don't have an exact temperature, but we recommend they are mounted to a metal surface away from other wires.
Hello, great video, very instructional. I have a question, Which resistors (Value) are appropriate for a 2018 Jeep Renegade Altitude brake/Turn led 1156?, Thx
Our LED resistors work on all model brake and turn signal bulbs. You can find them in the link provided below depending on how many you need!
www.diodedynamics.com/catalogsearch/result/?q=resistor
Followed video. Didn't work. Ideas for troubleshooting? Can I remove and try again or are the wires shot now?
More than likely you just didn't make a solid connection with the turn signal power and ground. We would recommend re-doing those connections, and confirming those wire colors. If you are still having troubles, please shoot us an email at contact@diodedynamics.com and we can assist you from there!
I installed these with the resistors in one side (passenger) and then I decided to test them. Neither side hyper flashes. Any reason why the driver side isn’t hyper flashing (without the resistors)? I’m thinking about not installing the resistors in that side...
Hey Mike - you will need one resistor per blinking bulb, as more than likely this was due to the CANBUS system when testing.
I have a 2018 Sahara Unlimited JL. I installed the switchback bulbs purchased through you, but they stay solid amber. Come to find out after doing more research, the switchback bulbs wont work on the Sahara JL model. Would these resistors solve this issue? (the issue being that the lights are amber and not white LED at all)
You will need to install resistors with these bulbs! Go ahead and shoot us an email to contact@diodedyanmics.com, and our service team will be happy to help you troubleshoot!
These worked to kill the hyper flash on my DD LED turn signals. I also bought the tail lights which I love. Can someone please tell me which wires I need to install the tail light resistors on? I can't find a JL tail light wire schematic yet and I'm too lazy to chase the correct wires myself. Anyone know which color wires I need? Thanks!
Hi Tony, thanks for your support!! Please go ahead and give us a call at 314-205-3033 Monday-Friday 9 a.m.- 5 p.m. CST, or shoot us an email at contact@diodedynamics.com, and our service team will be happy to help you with that!
Any idea why the turn signal works but the headlight doesn't?
Hey there! Please give us a call at 314-205-3033, Monday-Friday 9 a.m.- 5 p.m. CST, or shoot us an email at contact@diodedynamics.com and our service team can assist you!
The resistor gets really hot so much you can't touch it. Is this normal?
Yes, this is normal. We recommend mounting them away from plastics, fabric, or other wires.
I want [need] light bar for my JL!
Awesome! We plan to release more products in the coming months!
Can I extend the length of the wires?
Hi there! Please go ahead and give us a call at 314-205-3033 Monday-Friday 9 a.m.- 5 p.m. CST, or shoot us an email at contact@diodedynamics.com, and our service team will be happy to help you with any installation questions!
This does not work for Sahara Unlimited models, for there are two bulbs. If you install a switchback it will stay white and the other incandescent bulb is your blinker.
When installing these, it will be one resistor per blinking bulb, so the same idea applies to all makes and models. The resistor will need to be tapped into the turn signal power and ground.
For the Sahara unlimited. I am upgrading to the oem led DRL and blinker. I would need two resistors? One for blinker and one for DRL?
@@tysonnez2009 Hi there! What year is your Sahara?
Diode Dynamics 2019
@@tysonnez2009 You will need a pair for the blinkers, but you shouldn't need one for the DRLs!
What resistor did you use ? I swapped from sport fenders to rubicon fenders with leds . I now have rubicon leds and wiring harnesses. Will the wiring color still be the same ? Will resistors work for the factory led setup ?
Our resistor kits are universal! You can check them out below!
www.diodedynamics.com/led-resistor-kit-pair.html
If you are looking for an example for an install, you can check out the video below!
czcams.com/video/WyUh1ztBH84/video.html
I think you need to show us how to do it on a work bench or move you hands out of the way ,cant see what you doing..thx
Hi Dean! We appreciate the suggestion and will be sure to pass it along to our media team. In the meantime, please feel free to give us a call at 314-205-3033 Monday-Friday 9 a.m.- 5 p.m. CST, or shoot us an email at contact@diodedynamics.com if we can answer any installation questions!
If I don’t install the resistors, would it mess up the system, with the hyper flash ? Basically can install my LED lights without the resistors and be okay ?
Hi there! Yes, you can install these bulbs without resistors, however it will likely cause your blinkers to hyper flash.
Diode Dynamics would my Jeep be okay with they hyper flash ?
The hyper flash shouldn't cause any issues with the rest of your Jeep's normal functions.
Diode Dynamics do you have LED headlights? For the Jeep Wrangler, if so can you do an install video? Thank you so much for answering all my questions.
Happy to help! We plan to release our SL2 LED head lightbulb for the Wrangler in the coming months, and we will definitely do an installation video!
Why in the hell don't these car manufactures go ahead and start installing all LED lighting on new vehicles being sold. They are cheap now, efficient and long lasting. Stop using it as an "upgrade option" to suck more money out of our asses.
Yes