Video není dostupné.
Omlouváme se.
How to Cut Laser Straight Fence Posts
Vložit
- čas přidán 25. 07. 2024
- I recently built a beautiful, modern, horizontal style fence that does not use fence post caps. Therefore, you really need to have nice straight and level cuts for the post tops!
In this video I will show you how to build a small tool to achieve straight cuts on your posts with a sawzall (reciprocating saw). This will work to cut 6x6, 5x5, 4x4 posts without issue.
Enjoy!
****************************************************************
If you enjoy and have benefited from my content and are feeling generous I would love your support! You can "buy me a coffee" here:
► www.paypal.com/donate/?hosted... ☕
By supporting my channel you are encouraging me to continue with this time consuming endeavor. A lot of time goes into design work, building my projects, filming the videos, editing the videos, etc. Plus it all costs money! Your generosity goes a long way in helping me bring you better content as often as I can!
Follow me on Instagram!
► / embraceracing 📷
If you liked this video, perhaps you will also enjoy some channels that I personally find inspiring and interesting...
DIY and MAKER:
► The Hacksmith
/ @hacksmith
► Adam Savage Tested
/ @tested
► Thomas Sanladerer
/ thomassanladerer
Car Content:
► Mighty Car Mods
/ @mightycarmods
► Drivetribe
/ @drivetribe
#diy #woodworking #fence
Not building a wooden fence, but taking this tip in for when I will be able to use it. Excellent results and straight to the point.
Thank you! Something to remember down the road :)
I like this. Nice, simple, and elegant.
Thanks for the kind words!
Good trick! When you cut posts square and flat like that, its good to cover them with clear caulking or pitch to keep water out from swelling or freezing which can cause the post to crack and split. Some folks will cut their posts tops at 30-45º in order to allow a natural slope for the rain to run off.
Thanks for the advice Shannon. I put some of the wood treatment on and I also had a horizontal "runner" or whatever you want to call it on the top of my fence protecting the posts :)
Great video sir, thank you. I built my fence last summer, but didn't get a chance to level out the posts before the snow flew. My original plan was to hit each post with my circular saw and finish with a pull saw. This is sooo much better. I have 40+ posts to cut so, enough said. Also, new subscriber, after a quick scan of your other videos, I'm a fan.
Thank you so much! This method should work great, I did about 24 posts or so with this method and flew through. The circular saw method is okay if you can get through in one shot, but if not the cuts will almost always be misaligned. Won't have to worry about that with this method :)
simple and practical! nice work!
Thank you!
Nice tip!
Glad you enjoyed!
Nice work.
Thank you!
Innovative idea. Thanks for sharing!
My pleasure 😊
Perfect! Great video!
Thank you!
This is great, thank you! Quick question...what do you use to line up the holes on either end of the 2 pieces angle iron? Clamps? A vice? TIA!
I was using a level to mount one side first, and then using the level again to line up the opposite side so you get it level across a flat plane. Thanks!
What a great idea. I will be building one or two of those my friend 😊
Awesome!
BRILLIANT!!!!!!!!!!!!!!!!!
Thank you!
Just so happen to have about 6’ of angle iron lying around . 🍻
Perfect!
This is awesome! One question: how did you affix the jig to the post so it doesn't bounce around during the cutting? Did you clamp it? Thanks in advance!
Yes I did, I drilled two holes in the jig and then used screws to temporarily affix the jig to the post while cutting. Thanks!
My situation is just a little different. I need to trim off only about 1/4" to 1/2" on deck rail post. If I were to screw to each side of the post just 1 piece of angle iron and run my sawzall along it, can I still expect to get a nice clean cut?
I think you could. You're going to have to try and go slow and perhaps apply some downward pressure (not too much, the blade will bend and likely get a cupped cut) but enough pressure toward the angle iron that the blade stays flat and doesn't want to wander up.
@@EmbraceMaking Thanks. I may have a couple of pieces of 4x4 laying around that I can practice on before doing the deck posts.
One inch wide angle iron? Thanks!
I believe it was, yes!
Firstly great video. First one I found after seeing 6x6 recipromate post jog. That beings said, consider the costs before you do this You may find that it might be cheaper to buy it from them. I didn't, but here's my Lowes list:
(4) x Perforated-Slotted Angle iron 1-1/2" x 1-1/2" x 1ft ( Prod.# 11104)
non galvanized 5/16 hardware:
(4) x 1-1/4" long bolts
(2) x 8" carriage bolts or 6" if you're only planning on doing 4x4 posts.
(12) washers (two in the middle, one on the bottom)
(6) nuts
Total: $35.XX CAD with tax.
Summary: Factoring my time and gas "and this isn't one those enjoyment through the build things as it's mostly just simple assembly" I probably would have been better buying the jig as it's the same price.
Good point. I think I had most of my material left over so it made sense for me to just make them.
@@EmbraceMaking - having the angle iron would have saved me $24. In any event, I have laser straight cut post tops and for the price and peace of mind it was worth every cent. Thanks again for the selfless donation of your time.
@@anodtothevoid You're welcome, glad it worked out for you!
Got a new fence put up, the guy who done it cut the posts freehand with the smallest chainsaw i have seen, and it was as straight as could be done...but i think i would have to use this jig, looks idiot proof ..
Yep its pretty idiot proof thats for sure! Thanks for watching!
@@EmbraceMaking ..Finished all my posts, worked a treat, bought the parts from BQ, and made one, very satisfying when you make something yourself..i only had 6 posts to do, was better than waiting on my guy coming back to cut them for me..i just like making stuff lol
@@EmbraceMaking Every time I build something idiot proof..... They build a better IDIOT!!! LOL
smart
Thank you!
I’d attach a mitre saw to the post.
I started with Woodprix plans.
A lot easier to buy on Amazon for like $20. Lol
For sure, but what fun is that :p
Link?