Stuck Flywheel How to Remove Stuck Flywheel on Outboard Motor
Vložit
- čas přidán 23. 07. 2024
- T-Mikes Website
t-mikesvintageoutboards.com/
T-Mikes Ebay Store
www.ebay.com/str/simtechfarms
T-Mikes Logo Coffee Cup
t-mikesvintageoutboards.com/p...
T-Mikes Mail In Repair Service
t-mikesvintageoutboards.com/m...
T-Mikes Parts Broker Service
t-mikesvintageoutboards.com/p...
T-Mikes Service Offerings with Prices
t-mikesvintageoutboards.com/r...
Master Tuneup Kit
t-mikesvintageoutboards.com/p...
Tuneup Kit (no coils)
t-mikesvintageoutboards.com/p...
Coils
t-mikesvintageoutboards.com/p...
Tuneup Kit
t-mikesvintageoutboards.com/p...
Spark Wires
t-mikesvintageoutboards.com/p...
Spark Plugs
t-mikesvintageoutboards.com/p...
Fuel Pump Conversion Kit 5.5 HP
t-mikesvintageoutboards.com/p...
Fuel Pump Conversion Kit 7.5 HP
t-mikesvintageoutboards.com/p...
Fuel Pump Conversion Kit 10 HP
t-mikesvintageoutboards.com/p...
Fuel Pump Conversion Kit 15 & 18 HP
t-mikesvintageoutboards.com/p...
7.5 10 HP Fuel Pump 18-7350
t-mikesvintageoutboards.com/p...
18-2682 9.5 10 15 HP Gearcase Kit
t-mikesvintageoutboards.com/p...
5.5 to 18 HP Carburetor Kit 18-7043
t-mikesvintageoutboards.com/p...
3 to 7.5 HP Impeller 18-3001
t-mikesvintageoutboards.com/p...
9.5 10 HP Impeller 18-3003
t-mikesvintageoutboards.com/p...
15 18 20 HP Impeller 18-3002
t-mikesvintageoutboards.com/p...
Flush Kit 5.5 6 7.5 9.5 10 HPs
t-mikesvintageoutboards.com/p...
Stop Switch 9.5 HP
t-mikesvintageoutboards.com/p...
Tiller Grip 1958-1968 3-50 HP 52-1001 204188
t-mikesvintageoutboards.com/p...
52-1003 Lever Pin 0304155
t-mikesvintageoutboards.com/p... - Jak na to + styl
Just found your video, been fighting with this flywheel for an hour, your truck worked like a charm
It worked. I have a 1975 Evinrude 85 hp outboard and the flywheel was so tight. Looked up what to do with a stuck flywheel and your vid was the first one. It took about 5 cycles of thumping with the 5 pound sledge then tightening slightly. Finally popped off. Replaced stator, ignition coils and rectifier. Fixed all the issues I had.
Thank you, I'm now a subscriber, I appreciate you.
Chicago Mark here. Thanks T Mike for the great video. I did remove the flywheel from my 73 evinrude 18 hp using your method. Thanks again.
Great tips. Worked for me on my 25 yr old Yamaha 8 ps ! 3 times three strikes and pop went the fly wheel.
Your videos are awesome and so helpful! I was hesitant to keep cranking with my fly wheel puller, worrying I would strip the bolts. This video helped me get me get my stuck fly wheel off after 3 rounds Keep the videos coming!
I love the way you speed up the commercials.
Thanks again Tmike. Your videos are always great! Stay cool and please never stop what you do.
Anytime that I have removed a flywheel prior to reinstalling I used anti seize to make it easier to remove the next time. Yes the crack shaft is tapered as well as the flywheel it really does not have fit snug like tapered tool in a lathe or drill press. I have also had success removing the stuck flywheel by tapping on the perimeter of the flywheel rather than on the top of flywheel puller. And if really necessary I will evenly heat the flywheel but not too hot!😀🛫
The only thing I could add is to try and lift the puller (if you can) as you are hitting with the hammer so that you aren't pounding the bearings in the power head as much.
I would file or use a small grinder to make the top of the puller able to use a socket wrench again. I also like the 3 whack trick then retighten the bolt. Thanks.
You make good job. Can you work sometime on evinrude 2 hp +/- 1978 and explaine the maintenance regard's
Great video!
Great Video Mike 👍
Mike. Excellent video as always.
I find that sliding in shims to lift the flywheel helps too. That gives the crankshaft a little room to “drop” out of the flywheel.
Do you EVER use heat? Doesn’t the heat demagnetize the magnets?
Bien fait, mon ami Ti-Michel !
Mike
I’m about to remove the flywheel on a 1940 3.3hp Evinrude.
It has no holes for a puller…
So how do I get this one off?
I’ll make a video
@@michaeljsimonplease make the video !!!