THE BRAND NEW ENGINE IS ALMOST DONE! 💯 Cylinder and clutch mounting Puch Maxi ADDY
Vložit
- čas přidán 15. 07. 2024
- Today Chris and Erik will continue building the new ADDY 50-1A block! So far everything is going according to plan!
The setup of this moped:
- ADDY engine | bit.ly/ADDY-motor
- DMP 2.0 Crankshaft | bit.ly/ADDY-Kurbwelle
- Claw clutch | bit.ly/ADDY-Claw
- MLM clutch housing 21 teeth | bit.ly/ADDY-Kupplung
- PVL ignition | bit.ly/ADDY-PVL
- Driveshaft with helical gearing |
- Airsal 70cc NM | bit.ly/ADDY-70cc
- PSR head 70cc NM for Airsal | bit.ly/ADDY-PSR
- Manifold 15mm | bit.ly/ADDY-Ansaugstutzen
- Bing 15mm | bit.ly/ADDY-Bing
- Original air filter | bit.ly/ADDY-Luftfilter
We've reached the cylinder/head and clutch, so we're almost there! They also discuss the number of Newton meters you can tighten different parts with! Good to know.
Enjoy watching, and leave a comment in the comments what you like about this show!
00:00 Intro and what do we need today?
03:15 Installing the clutch
21:50 : Cylinder installation
Puchshop.de - The online Puch shop from Puch fanatics, for Puch fanatics.
► www.puchshop.de
Puchshop.de - The online shop for cheap Puch parts
With over 70,000 Puch parts and accessories in stock, Puchshop.de is the largest online shop for Puch parts and accessories. Due to our large stock and fast service, we can often ship the same working day.
Follow us on social media and stay tuned!
Link tree ► www.linktr.ee/puchshop
Facebook ► / puchshop
Instagram ► / puchshop - Auta a dopravní prostředky
Immer schön wenn der Chef auch weiß was er tut und auch selber schrauben kann. !
😎
Zoals altijd weer een super duidelijke uitleg hoe het goed gedaan moet worden.
Wenn der Motor fertig ist,,, schickt ihn mir zu Weihnachten 😉
Danke für deine Arbeit Chris, toller Kanal 🖐
Danke! 🤩
Entgraten ist das deutsche Wort was ihr sucht 😉
Nimm für den Kolbenring einen kabelbinder drumm, aber dreh den Binder so das er nicht rastet damit du ihn einfacher entfernen und wieder verwenden kannst
Top video's! Ik ben ze allemaal aan het kijken. Ik ken van vroegen maar 1 ontsteking bosch met de puntjes. Ik zou best wat meer willen weten over de verschillende ontstekingen
Daar kunnen we vast een keer een video over maken!
Ist das nicht im Endeffekt Porten?
Ik zit te genieten van jullie enthousiasme, en nieuwe puch delen. 👌
Maar koppelings moer met 35nm aandraaien? (koppeling zit bij een goede conus passing, met veel minder NM al muurvast) 👍
We zeggen altijd, vast is vast! Alleen 'volgens het boekje' moet de moer zo strak...
Auf Deutsch sagt man Kanäle Entgraten oder Kanten Brechen 👍💨
Ahh super. Danke!
In English we would say bevel or maybe chamfer. De-burr too, many words to explain the process!
äh,äh,äh
Auf Deutsch sagt man Kantenbrechen beim Zylinder
Ah super! Danke!
Kanten brechen, mache ich sowieso immer.
Top top!
Bevel auf deutsch =fasen
💯