Part 2 - How to Rebuild a Cummins Diesel 12 valve 5.9L 6BT Engine
Vložit
- čas přidán 23. 08. 2024
- In this video we show you how to install the pistons and rings in your Cummins 12 valve 5.9L 6bt diesel engine. These procedures also apply to the cummins 4bt engines.
Visit www.adventurevehiclesnw.com for conversion parts.
This has to be the best 6bt rebuild video on CZcams! Great job sir
Thanks!
Thumbs up for the way to measure bore taper👍👍👍
Yep, at 18:30 , the #1 piston is going in backwards. It was either a test, or a testament as to why you should install the pistons without the crank in place. Seems like all that has to be done is carefully lube and spin the #1 piston around...
The piston was rotated around. It was just how the video was edited.
Nice we are learning ,
انا سعيد لان نكتشف قناتك شكرا على تقديم هذا المحتوى الجيد
@ 18:30 it looks like you put the piston in backwards is this true?
I saw that
15:43 would'nt it be easier to just dunk the piston into a bucket of that stuff? lol
excellent video Thank you very much solved some doubts I had
Thanks man? The rings in my kit arnt marked top and came with no instructions. Put the chamfered edge up on second and part no. up on first👊😎
This is a great series. Butttttt. Did that first piston go in backwards?
The piston was rotated and installed correctly. The Video editing made it appear it was installed wrong. Thanks for watching the video so closely!!.
@@Jonesys 100% here to learn man I really like this series. You were so informative that it did in fact “look” as though it went in reversed to what you said. But thank you for taking the time to educate the people like me.
Hii when to replace piston and liner.
And you have honed the liner so will insert over size piston ring or normal piston ring
What about changing out the frost plugs....The front one is showing some rust.
Excellent video...How much does this engine weigh...what size Engine Stand do I need to hold a 6bt ?
Liked/Subscribed !
I believe they weigh about 1200 "fully dressed"
A paint brush would work too lol
Kindly assist. .. 12000 of an inch would be less than 3000 of an inch , whereas for 4 inch bore taper tolerance should be around 750th of an inch ... Pl correct me .. tricky situation
What brand and part number are those rings?
Why do there seem to be holes in the top of the pistons? I know nothing of diesel internals, but I assume the design is to allow some pressure release due to the super high combustion. Am I close?
It has to do with how the explosion is distributed across the piston as well as the flow of air and fuel so it can mix more efficiently.
Kurt Dukes, what you're seeing is the actual combustion chamber. The underside of the cylinder head on a direct injected diesel if completely flat unlike their gasoline counterparts.
How did you get the parts like the pistons so clean thanks
I cleaned everything in my insta clean recirculating parts washer.
Jonesy hey show/ or tell me more of your parts washer.
What if you just filled a 5 gallon bucket with lubricating oil and just dunk the entire piston in the oil like a infant baptism
Is that amount of wrist pin play normal on a 5.9?
i thought exactly the same around the 14 minute mark where hes lubing the gugeon pin up
When the rod and piston are not installed in the block there is a fair amount of play between the top of the rod and sides of the piston if that’s what you mean. When pistons in and rods bolted to crank it kinda takes up the slack.
Yo acabo de quemar mi 6bt ;(
Como fue que lo quemastes!?
Why did u rebuild this engine is everything was. Isn’t that a waste of money. Was there blow by or something that u thought was wrong with it or was this just a how to video
No offense, but seams like a waste of time on rebuild, looks like it was good to go for another 200k