The problem with this video is that it is so good, you’ve convinced me I can do my own fence, but I know from experience watching you makes it look easy, actually doing it is another story 🤣
I have no need or have any intention to do any fencing...... But i love to watch a crafts person doing a job well & explaining all the pitfalls.... Thank you for sharing 👍🏾
Everything about this procedure is spot on and very well explained. I've just used a similar method to fix a 100mm square gate post. For those with particularly brittle bricks or London's with the large frog, I'd suggest using 10mm allthread and chemical fixing adhesive such as Kem II. Recessing the timber holes is done in the same way, allowing for a nut and washer. Remember to check your thread lengths so they don't fall short to apply the nut and washer. For those keen on a fine finish can always plug the holes once complete.
Why have I not found you earlier! Excellent video, I'm crap at DIY but you take it step by step and explain everything without it becoming boring. Really pleased I've found you. Thanks mate, keep up the good work
This concrete screws idea will solve my current problem of an existing post has come loose from what looked like thin screws into rawlplugs into house brickwork. The whole fence is unstable at the house end and raking it apart is not in my capability or strength. I can drill through the wood post in situ though and put those heavy duty concrete screws in. Grateful for this video!
WOW! Once you mentioned bevelling the post i nearly tuned off - far too complicated for me I thought - but you simplified working out the angle so well that even an idiot like myself can work it (not that i need to because my wall and fence are parallel to each other!) The only other element I found not very DIY basic was the laser thingie - not got a one of those and don't want to waste money on a piece of equipment just to attach 3 posts. Had tuned in mainly to see what you used and was pleasantly surprised to see no raw plug required. Years of doing my own DIY from laying patios, house renovations, electrics, plumbing - i have never plucked up the courage to drill into brick!! Flippin' simple following your video!!Thanks alot!! x
This was a revelation. I was waiting for you to drill a hole large enough for a big old plastic rawlplug and you just screwed the bolt straight into the brick! I just never knew you could do that.
No idea how I ended up here. I'm not even putting my own fence up. But I had to see the finished article. Looks great! And very informative. Good job. 👍
I had a similar issue a few years ago, but wanted to fit a gate. I didn't bevel the fence posts though - I simply fitted the hinges to the flush fence posts in the normal way and let the hinges absorb the angle. Worked well and looked good!
This is why a professional job sometimes costs more than you'd expect. It takes a lot more time and effort to do the job properly. I used rawl plugs and large 10mm screws when I fixed my post to the wall. It seems secure enough.
Great video. Have done much of this over the years. I have drilled slightly smaller holes in the brickwork for concrete bolts to ensure. 10mm bolts, 10mm hole in post, 8mm holes in block/brickwork. I also drill and loosely fix bolts one at a time starting at the top, so you don't have problems if there is any movement.
In regards to the post fixing 100% the fencing on the other hand is not correct bottom rail to low, using screws instead of 50mm galv nails and no gravel board support in the middle good effort nevertheless (I’m a fencer)
You are really natural in front of the camera. I'm surprised you aren't on a professional show. You have good charisma are well informed and entertaining. Impressive.
1st of your videos I have watched. Not sure I have seen a more concise, well paced, well edited DIY video as yet. Also excellent camerawork and audio (including sensible use of music instead of a constant bed fighting with the presenter). I'm really looking forward to watching loads more. :)
Going to be doing a gate and a little bit of fencing. I was worried about the screws I'd use, or if I needed to use rawplugs, etc, and whether to drill into the mortar or brick. All questions answered and all concerns set aside. Excellent vid. Many thanks 👍🏻
Really appreciate this film. I need to replace rotten pieces of Door Jambs on our garage door, watched several films and was about to do an easy project, but then realized that all the films I saw before were about attaching that Door Jamb to the wood, and we have brick house, with the Door Jamb attached to the brick. The project turns to be from easy to not so easy, but I can proceed after this film. Thank you!
@@ProperDIY I have another a question here: can I actually use the original holes and concrete screws? I will cut like 24 in from the bottom of the Door Jamb and replace it with a new piece of wood. Or I need to make an attachment in another place? In other words if you unscrew that concrete screw, can you screw it back, or it is like an ancor in some sense, and it is better not to reuse it? Thank you again.
@@olenaerhardt7725 Yes you can reuse them and the holes. Just ensure that when you tighten them fully they hold well - this sort of depends on how hard the brick/block is. If it's normal brick it will be fine.
Great video and good advice. 9:07, no need for pilot holes if you use a cutter design, of outdoor quality screw such as reisser. But as usual you will pay more for the convenience and time saving.......;)
Tip, put washing up liquid on thunderbolts before driving them into the brickwork. Makes life a lot easier. And ensure hole is drilled at least 10mm deeper than length of screw.
This video is very helpful, wonder why I didn't search before. I love the step by step explanation, great. I am a DIY er and this adds to improving my abilities. Looking forward to watching more.
The mechanical advantage of a screw thread driven by a 12” ratchet over a 6ft length of 4” pine is huge, especially with high tensile bolts. It would be easy to obtain a 2” deflection over a 6ft length. I’ve tried to use the stuff for forming jigs, and it’s useless. Only oak, ash or 6” pine was good enough. Nice work. I like your attention to detail on the join to the main fence.
Great video, but I wondered the entire time If a fence that would open wouldn’t have been a better item to put on that side of the house. Now you have to walk all around the building to get to the other side.
Great suggestions...loved the string to line up the screws. Loved the intro wherein you shaved off some of the 4 by 4. I would not have lowered the bottom 2 by 4 to ground level or below due to rain and in Canada snow. Animals will just dig under. Wind will eventually move the fence possibly as I left mine open in between a little....sort of...a 80 year old neighbour from Ukraine wandered over and took over. He could not speak English so the screws did not line up...and there were some things that he did that I would not...but my Lancaster mother taught me to respect age...hmmm? I loved the drawings. I guess when I make the gate, I will not trim off the 4x4 but will move the opposite side on the 90 degree angle and hope it works as I try to do an l shape to a metal fence...right? Well, as long as it holds to the grandchild is old enough to walk into the front...a good 2 years. But, thanks for sharing...quite professional. Oh,....thanks for the idea of countersinking the bolt. I am a super and the men that, long ago, did a fence and gate...did NOT sink the screws which seem to have caused a gap in the apt where I am living so the gate is tight due to the screws
Hi Stewart, thanks for your kind reply. All done now, you were totally right about the intense bitting in the wall!! It fixes extremely well indeed. Much much better that old fashioned rawl plugs! Thank you!
Masonry screws are designed to be removable and they support a much lower load than the same-size bolted anchor. Masonry screws are typically used for temporary fixings. In a permanent installation, a bolted anchor is far preferable. In this case, a (expensive sadly) galvanized M12 or M16 bolted anchor would be ideal.
Just found your channel. Looks good. Personally, and we all have our different ways, I have learnt over the years to always resin when affixing to brick/concrete. Yes, concrete screws can be very strong, but resin is fit and forget. Nice to see a fellow 🇬🇧 doing stuff like this on CZcams 👍👏
Thanks! I agree resin is absolutely the best fixing into a wall like this. In my day job I have used construct resin like Hilti Hit' which will fix anything. The negative side is it's permanent and not cheap. The average DIY'er will not be inclined to use resin.
@@ProperDIY Hello Stuart. Also very impressed with the concrete anchors into the brick. Are you able to tell us the manufacturer and name of the product? Would like to see if they’re available in the US. Love the videos!
Great video thanks, I learned quite a bit from that. Could I suggest that you cut a hole at the bottom of your fences to allow hedgehogs access? Lack of hedgehog highways is one of the reasons they are in decline.
Vital tip 👍🏻, we have hedgehog holes in front back and side fences and we regularly have hedgehogs in the garden sometimes they even hibernate in our hedgehog houses 😀🇬🇧
Nice video, used these fixings to hang a gate post on my brick wall. Top tip = spray the hole through the wood and the brick with some wd40 before putting the fixing in. Saves that nasty squealing and makes them easier to do up.
Great video. Top marks on the way you explained how to trim the post. A difficult thing to explain. You did it very well - the advice was very clear and easy to follow.
Thanks for this. Good to see the job done properly. I fear that left to my own devices, I'd have missed a couple of steps out. I'm hoping my subscription to your channel will keep me on the straight & narrow. You need to re-think the background music... methinks. ⭐️⭐️⭐️⭐️⭐️ 🇬🇧
Very like myself. Some 'belt and braces' stuff, but that's good. As a joiner who's had to retire through illness, i find your videos informative and interesting.
Having watched you build the garden planter, you took this to another level. First class job, it makes a difference having all the tools but you certainly know what you are doing..........keep it up 👍
I work like you do, proper planning at each step. The problem comes if I try to hire someone. Cannot find contractors capable of this kind of exacting workmanship.
Lol. Contractor and exacting workmanship! They area rare species indeed. If you can find one to do even a half decent job you’ve won the lottery. Your only hope is to do it yourself!
I found that extremely interesting and useful. Would you consider showing how to fix a post to and irregular brick wall please? By irregular I mean a brick wall that is not straight up and down.
Ahh this is excellent! Exactly what I been looking for. Complete DIY noob here, had a pop at hanging a gate off the concreate post after (eventually) ripping out the ol' rotten one... After about 6 hours and a lot of swearing as my spindly little bolts kept snapping I came to learn the error of my ways. this video should do me justice, I feel much more comfortable tackling this., I'll let you know how it went:P Again, thanks a lot
I gotta say I think you are one of the 'OCD' tradesman that take longer to do a job than some fly-by-night who has a nail gun in his holster, takes his money an runs. But I take my hat off to you, not a major construction project but it a damned got job pal, very neat and precise and looks smashing, well done 😊
The amount of experienced tradespeople who don't understand the difference between a "pass thru" hole and a pilot hole, leaving posts wobbling!! Good advice 👍🏻👍🏻
An alternative way to create the angle (which might be a bit easier than sawing the angle) is simply to work out where the gap is 1/2" wide between the wall and the post. Then you can buy a piece of timber 1/2" square and screw it on to the side of the post, at the point where the gap is 1/2". Different sizes will also work at different points That will create the angle for you without the cutting. I used one of those concrete screws for the first time on a kitchen fitting job a few days ago. Normally I would drill a pilot holes for pozidrive woodscrews in the timber post, put the screws in the post, so the screws were just projecting out the other side of the post. Then I would offer up the post to the wall and tap the screwheads to get a witness mark on the wall (mark with a pen to make clearer). Then drill holes with a masonry bit and put in rawplugs. Once I've done all that I can offer up the post again and put the screws in. Works a treat, and most times produces a really good fixing, but it is a faff. Those concrete screws just go straight through the lot! no irritating rawplugs that are too short so you have to drill deep and try to put two in, only to have to cut the second one in half because it won't go in the whole way. What a palarva! So nice one for showing us all the new fitting system!
Brilliant job 👌🏻only criticism is the gimmick music I think you don't need that in you're video's ..... Subbed look forward to seeing what you do next .
Love your work Stuart, I’ve watched every video and your attention to detail how AND why is so useful. My only complaint, more videos please I’m getting withdrawal symptoms 😂👍
I’m just a diy dad who’s now taking a 15 year old pressure treated deck apart It’s biggest failure part was the ( post direct to wall in this vid ) My question as a diyer : would it have been any benefit to put a plastic packer between the post & brickwork to allow airflow through Any advice appreciated & thanks 🙏 again for your time making another excellent vid
I hope you have a table saw in your new workshop to make that bevel easier. Also you could have drilled your countersunk holes for the fixings before you did the bevel. Would make getting them straight to the brick work easier. Good tip on the order of the countersink. I've made that mistake before
Slight mistake describing the counterbored hole a countersunk one for the bolt head clearance. Brilliant video tho, great to watch step by step with explanations all the way through.
I just realised that there's nothing you can't do I will call you in a fortnight to come and do my garden and lots of things including the house alarms 😀
QUICK TIP: Drill your holes before you cut the angle... that way they'll definitely be 90 degrees to the brick when fixed! Quality video as usual. 👍
Fantastic tip. Thank you
Could you explain this a bit more? I am trying to do a fence gate, so this might save me time.
But if uou drill before you cut the wood, it would go in at an angle, the idea is to drill after cut so it's straight to the brick
@jamesfukndee no mate it will mean it goes into the brickwork at 90* and have a proper fixing. Best to drill then cut.
The problem with this video is that it is so good, you’ve convinced me I can do my own fence, but I know from experience watching you makes it look easy, actually doing it is another story 🤣
Great job! Used these bolts to fix my timber to the wall yesterday when I put a gate up. Never heard of them before but they fixed really solid.
Always clear! Greatest handyman teacher on the web! Love those fixings - seem so much better than the hammer in type which I've never been happy with!
Wow, thanks!
Remembering that the countersink should not be based on the size of the bolt head but the size of the socket you’re going to use to fix it.
True dat..
@@guysolis5843 it is no need to ask how I know😂
Remembering that it's a counterbore not countersink as that would imply chamfering the through hole, not drilling a blind bore as he did
Ok Dad...
@@YAWN.... Pleasure
I have no need or have any intention to do any fencing...... But i love to watch a crafts person doing a job well & explaining all the pitfalls....
Thank you for sharing 👍🏾
Thank you
Everything about this procedure is spot on and very well explained. I've just used a similar method to fix a 100mm square gate post. For those with particularly brittle bricks or London's with the large frog, I'd suggest using 10mm allthread and chemical fixing adhesive such as Kem II. Recessing the timber holes is done in the same way, allowing for a nut and washer. Remember to check your thread lengths so they don't fall short to apply the nut and washer. For those keen on a fine finish can always plug the holes once complete.
Why have I not found you earlier! Excellent video, I'm crap at DIY but you take it step by step and explain everything without it becoming boring. Really pleased I've found you. Thanks mate, keep up the good work
Thank you and Welcome aboard! Only been going since Jan so still very new to everyone!
This concrete screws idea will solve my current problem of an existing post has come loose from what looked like thin screws into rawlplugs into house brickwork.
The whole fence is unstable at the house end and raking it apart is not in my capability or strength. I can drill through the wood post in situ though and put those heavy duty concrete screws in. Grateful for this video!
WOW! Once you mentioned bevelling the post i nearly tuned off - far too complicated for me I thought - but you simplified working out the angle so well that even an idiot like myself can work it (not that i need to because my wall and fence are parallel to each other!) The only other element I found not very DIY basic was the laser thingie - not got a one of those and don't want to waste money on a piece of equipment just to attach 3 posts. Had tuned in mainly to see what you used and was pleasantly surprised to see no raw plug required. Years of doing my own DIY from laying patios, house renovations, electrics, plumbing - i have never plucked up the courage to drill into brick!! Flippin' simple following your video!!Thanks alot!! x
Literally thousands of videos on CZcams and this video is recommended everyday.
This was a revelation. I was waiting for you to drill a hole large enough for a big old plastic rawlplug and you just screwed the bolt straight into the brick! I just never knew you could do that.
I know! looks like rawlplugs are old fashioned now!
Depends on the type of brick, sometimes they just don't work...
Exactly what I was expecting to see. I'll have to look out for some of these concrete screws when I replace my gate post.
A spade bit produces a counter bore. A countersink is typically 45 degree taper for countersink screws. Yes a good informative video.
Well mannered presentation, good instruction and no fluff. Well done.
Thank you
Well said mate!
No idea how I ended up here. I'm not even putting my own fence up.
But I had to see the finished article. Looks great! And very informative. Good job. 👍
Glad you enjoyed it!
I had a similar issue a few years ago, but wanted to fit a gate. I didn't bevel the fence posts though - I simply fitted the hinges to the flush fence posts in the normal way and let the hinges absorb the angle. Worked well and looked good!
This is why a professional job sometimes costs more than you'd expect. It takes a lot more time and effort to do the job properly. I used rawl plugs and large 10mm screws when I fixed my post to the wall. It seems secure enough.
Correct
Great video. Have done much of this over the years. I have drilled slightly smaller holes in the brickwork for concrete bolts to ensure. 10mm bolts, 10mm hole in post, 8mm holes in block/brickwork. I also drill and loosely fix bolts one at a time starting at the top, so you don't have problems if there is any movement.
At last somebody who knows what they are talking about! Good tips good advice!
Very much appreciated!
In regards to the post fixing 100% the fencing on the other hand is not correct bottom rail to low, using screws instead of 50mm galv nails and no gravel board support in the middle good effort nevertheless
(I’m a fencer)
Top marks for PPE use!
My first time watching your videos and in the first 5 minutes I instantly subscribed. Great video mate
Thank you - very much appreciated
Same here 😁
You are really natural in front of the camera. I'm surprised you aren't on a professional show. You have good charisma are well informed and entertaining. Impressive.
Thank you so much 🤗I haven't been offered any show but I do have my own channel with no one telling me what to do so good enough for me!
@@ProperDIY Fair enough!
Brilliant no long winded story telling, few ground rules and off we go. We'll done
Thank you!
1st of your videos I have watched. Not sure I have seen a more concise, well paced, well edited DIY video as yet. Also excellent camerawork and audio (including sensible use of music instead of a constant bed fighting with the presenter).
I'm really looking forward to watching loads more. :)
I watched this in full and enjoyed it I must be getting old.
I know the feeling!
By old i think you mean wise?!
😁👌
Yup, how-to's for things we're never going to do. I don't have a single brick on my house but I'm here 🙃
Going to be doing a gate and a little bit of fencing. I was worried about the screws I'd use, or if I needed to use rawplugs, etc, and whether to drill into the mortar or brick. All questions answered and all concerns set aside.
Excellent vid.
Many thanks 👍🏻
Really appreciate this film. I need to replace rotten pieces of Door Jambs on our garage door, watched several films and was about to do an easy project, but then realized that all the films I saw before were about attaching that Door Jamb to the wood, and we have brick house, with the Door Jamb attached to the brick. The project turns to be from easy to not so easy, but I can proceed after this film. Thank you!
No problem - I'me glad you liked it and found it useful
@@ProperDIY I have another a question here: can I actually use the original holes and concrete screws? I will cut like 24 in from the bottom of the Door Jamb and replace it with a new piece of wood. Or I need to make an attachment in another place? In other words if you unscrew that concrete screw, can you screw it back, or it is like an ancor in some sense, and it is better not to reuse it? Thank you again.
@@olenaerhardt7725 Yes you can reuse them and the holes. Just ensure that when you tighten them fully they hold well - this sort of depends on how hard the brick/block is. If it's normal brick it will be fine.
@@ProperDIY I see. Thank you very much.
As an apprentice wood machinist. One my jobs was cut the arris rail ends to a bit of point. And make matching holes in the post.
Nice one!
I've been a fan of Dynabolts for years but those anchor bolts have just changed my mind.
If I could go back and do it all again, this is what I'd be learning. So satisfying.
Brilliant. Some great tips there. Is anyone else screaming 'gate! - make an access gate!!'....no, just me?
Great video and good advice. 9:07, no need for pilot holes if you use a cutter design, of outdoor quality screw such as reisser. But as usual you will pay more for the convenience and time saving.......;)
Tip, put washing up liquid on thunderbolts before driving them into the brickwork. Makes life a lot easier. And ensure hole is drilled at least 10mm deeper than length of screw.
This is like a City and Guilds workshop lesson. Wow. Thanks.
I use a pritt stick to fix timber to brick work, saved me a fortune over the years.
This video is very helpful, wonder why I didn't search before. I love the step by step explanation, great. I am a DIY er and this adds to improving my abilities. Looking forward to watching more.
Excellent tips. I never think of using line but to mark where the Arris rails are over featherboard, it's the only way!
This guy is the father figure I wish I'd had 👌
That makes me feel old however I'll take that as a compliment.
Really impressive job. I was just looking for tips on fixing gate posts to the wall, but really liked the fence and all the handy tips. Thank you.
Thanks. Just assume the fence post is a gate post!
Justin Timberlake would be proud
The mechanical advantage of a screw thread driven by a 12” ratchet over a 6ft length of 4” pine is huge, especially with high tensile bolts.
It would be easy to obtain a 2” deflection over a 6ft length. I’ve tried to use the stuff for forming jigs, and it’s useless. Only oak, ash or 6” pine was good enough.
Nice work. I like your attention to detail on the join to the main fence.
Quite right!
I’ve been watching your videos the last few days to get some ideas - they are great so thank you. Keep up the good work and I love the humour 👏🏻👏🏻
Glad you like them! Will do
Great video, but I wondered the entire time If a fence that would open wouldn’t have been a better item to put on that side of the house. Now you have to walk all around the building to get to the other side.
Always tended to use the shield anchor bolts but they look a tad outdated. Will be giving these concrete screws a try now they look ace. Good job 👌🏼
Me too and they now seem a bit old fashioned!
Cheers for the great guide, i'd never used concrete bolts before, will definitely use again.
Great suggestions...loved the string to line up the screws. Loved the intro wherein you shaved off some of the 4 by 4. I would not have lowered the bottom 2 by 4 to ground level or below due to rain and in Canada snow. Animals will just dig under. Wind will eventually move the fence possibly as I left mine open in between a little....sort of...a 80 year old neighbour from Ukraine wandered over and took over. He could not speak English so the screws did not line up...and there were some things that he did that I would not...but my Lancaster mother taught me to respect age...hmmm? I loved the drawings. I guess when I make the gate, I will not trim off the 4x4 but will move the opposite side on the 90 degree angle and hope it works as I try to do an l shape to a metal fence...right? Well, as long as it holds to the grandchild is old enough to walk into the front...a good 2 years. But, thanks for sharing...quite professional. Oh,....thanks for the idea of countersinking the bolt. I am a super and the men that, long ago, did a fence and gate...did NOT sink the screws which seem to have caused a gap in the apt where I am living so the gate is tight due to the screws
Excellent!
Hi Stewart, thanks for your kind reply. All done now, you were totally right about the intense bitting in the wall!! It fixes extremely well indeed. Much much better that old fashioned rawl plugs! Thank you!
Excellent! I'm so glad it went well.
This guys a legend. Are you local cos my wife's crap at DIY!
This is easily the best comment I've had so far!!! Very good!
8:24 onwards for a couple of seconds.... shut your eyes and just listen!!! 😂🤣😂🤣
Brilliant video, really informative and well put together!
Glad you enjoyed it!
Masonry screws are designed to be removable and they support a much lower load than the same-size bolted anchor. Masonry screws are typically used for temporary fixings. In a permanent installation, a bolted anchor is far preferable. In this case, a (expensive sadly) galvanized M12 or M16 bolted anchor would be ideal.
I don’t even have this in the job list but still enjoy knowing how to!
Good advice Jim, 👍I've done similar but used Dyna bolts to attach the timber to the brickwork, but your method is neater. Cheers Jeff.
Just found your channel. Looks good.
Personally, and we all have our different ways, I have learnt over the years to always resin when affixing to brick/concrete.
Yes, concrete screws can be very strong, but resin is fit and forget.
Nice to see a fellow 🇬🇧 doing stuff like this on CZcams 👍👏
Thanks! I agree resin is absolutely the best fixing into a wall like this. In my day job I have used construct resin like Hilti Hit' which will fix anything. The negative side is it's permanent and not cheap. The average DIY'er will not be inclined to use resin.
@@ProperDIY Hello Stuart. Also very impressed with the concrete anchors into the brick.
Are you able to tell us the manufacturer and name of the product? Would like to see if they’re available in the US.
Love the videos!
Great video thanks, I learned quite a bit from that. Could I suggest that you cut a hole at the bottom of your fences to allow hedgehogs access? Lack of hedgehog highways is one of the reasons they are in decline.
Vital tip 👍🏻, we have hedgehog holes in front back and side fences and we regularly have hedgehogs in the garden sometimes they even hibernate in our hedgehog houses 😀🇬🇧
@@AJ-qn6gd Excellent, thank you for that, they need all the help they can get.
Good point - a job for me tomorrow.
@@ProperDIY,Top man 👍🏻🇬🇧
Lovely job. Those concrete screw fixings are brilliant
Thank you
I'd agree. I used them to fit a canopy over my back door... Worked a treat.
Great advice always nice to watch these kind of videos they help you do the job only once rather than wastage. Thank you and please keep them coming.
Thanks, will do!
Nice video, used these fixings to hang a gate post on my brick wall. Top tip = spray the hole through the wood and the brick with some wd40 before putting the fixing in. Saves that nasty squealing and makes them easier to do up.
You can put nylon spacer between post and brick stops damp traveling.
Great video. Top marks on the way you explained how to trim the post. A difficult thing to explain. You did it very well - the advice was very clear and easy to follow.
Thanks for this. Good to see the job done properly. I fear that left to my own devices, I'd have missed a couple of steps out. I'm hoping my subscription to your channel will keep me on the straight & narrow. You need to re-think the background music... methinks. ⭐️⭐️⭐️⭐️⭐️ 🇬🇧
Thank you!
Get rid of the muzzak altogether we stopped the vid because of it
Very like myself. Some 'belt and braces' stuff, but that's good.
As a joiner who's had to retire through illness, i find your videos informative and interesting.
Well thank you very much.
I use these floor bolts for all my wood to Stone fixings, great things.
Absolutely brilliant, real professional, well explained, and suitably informative and inspiring enough for me to do mine! well done!
Thank you very much
We call those screws "Thunder bolts" here in Ireland. They really are a leap in the right direction.
Really enjoyed the vid. Professionally done with no faffing around, well done. I’ll be checking your other vids.
Thank you Swiss Tony! Lots more to come.
Spot on direction, like those bolts going to give them a go for double side gates posts. 👌
Having watched you build the garden planter, you took this to another level. First class job, it makes a difference having all the tools but you certainly know what you are doing..........keep it up 👍
Thank you
I work like you do, proper planning at each step. The problem comes if I try to hire someone. Cannot find contractors capable of this kind of exacting workmanship.
Exactly. Even with their so called 'professional training' no one seems to care as much about the detail as yourself!
Lol. Contractor and exacting workmanship! They area rare species indeed. If you can find one to do even a half decent job you’ve won the lottery. Your only hope is to do it yourself!
Cracking video, all bases covered, plain speaking, very well edited, spot on !
Much appreciated
I found that extremely interesting and useful. Would you consider showing how to fix a post to and irregular brick wall please? By irregular I mean a brick wall that is not straight up and down.
Ahh this is excellent!
Exactly what I been looking for. Complete DIY noob here, had a pop at hanging a gate off the concreate post after (eventually) ripping out the ol' rotten one...
After about 6 hours and a lot of swearing as my spindly little bolts kept snapping I came to learn the error of my ways.
this video should do me justice, I feel much more comfortable tackling this.,
I'll let you know how it went:P
Again, thanks a lot
I gotta say I think you are one of the 'OCD' tradesman that take longer to do a job than some fly-by-night who has a nail gun in his holster, takes his money an runs.
But I take my hat off to you, not a major construction project but it a damned got job pal, very neat and precise and looks smashing, well done 😊
Thank you I think. BTW I'm not a tradesman, I'm just a DIY'er.
Impressed by those bolts gripping hold !
Me too. If the brick is strong the fix is solid
Thanks for the great insight and step by step guidance on the fencing!
Thank you
The amount of experienced tradespeople who don't understand the difference between a "pass thru" hole and a pilot hole, leaving posts wobbling!! Good advice 👍🏻👍🏻
Thank you!
An alternative way to create the angle (which might be a bit easier than sawing the angle) is simply to work out where the gap is 1/2" wide between the wall and the post. Then you can buy a piece of timber 1/2" square and screw it on to the side of the post, at the point where the gap is 1/2". Different sizes will also work at different points That will create the angle for you without the cutting. I used one of those concrete screws for the first time on a kitchen fitting job a few days ago. Normally I would drill a pilot holes for pozidrive woodscrews in the timber post, put the screws in the post, so the screws were just projecting out the other side of the post. Then I would offer up the post to the wall and tap the screwheads to get a witness mark on the wall (mark with a pen to make clearer). Then drill holes with a masonry bit and put in rawplugs. Once I've done all that I can offer up the post again and put the screws in. Works a treat, and most times produces a really good fixing, but it is a faff. Those concrete screws just go straight through the lot! no irritating rawplugs that are too short so you have to drill deep and try to put two in, only to have to cut the second one in half because it won't go in the whole way. What a palarva! So nice one for showing us all the new fitting system!
Subscribed, good presentation, straight talking, clear instruction/advise and an easy manner.
Thank you.
I'm doing a similar job and I found your video very helpful. Thanks
Great video, my only concern would be the bridging of the damp course.
Great video. Easy to understand and kept it simple.
Thanks
Brilliant job 👌🏻only criticism is the gimmick music I think you don't need that in you're video's ..... Subbed look forward to seeing what you do next .
Thank you
Painful that generic yt music. Your content is fine without it.
The house will fall down before that fence 🤟🏻
Love your work Stuart, I’ve watched every video and your attention to detail how AND why is so useful. My only complaint, more videos please I’m getting withdrawal symptoms 😂👍
Imagine working for him ( not in the sense of learning things ) but one of those guys that everything got a story
I worked with him he’s a superb knowledgeable operator
Don't know how I found my self here but it was very educational.
Now to do a vid on that snapped fence post in the back ground 😉
I will do
Really enjoyed watching this one! Very good way of showing how to make a template for the angle to cut. 👏👏👏
Thank you
Excellent, clear demonstration.
Awesome advice. Thanks a million. Ive done some fencing before but there are a load of good tips from you. Nice one.
Thank you
Nice job. Love the detail of scribing then end board. A proper job! 😊
Glad you liked it!
Omg thank you. I literally have the same project with the same geometry. You're #1
Thank you for providing such excellent material
Brilliant video, Bravo. Makes it look easy but also gives me the confidence to do it myself. Thank you.
Thank you
@@ProperDIY mk
@@ProperDIY k
I’m just a diy dad who’s now taking a 15 year old pressure treated deck apart
It’s biggest failure part was the ( post direct to wall in this vid )
My question as a diyer : would it have been any benefit to put a plastic packer between the post & brickwork to allow airflow through
Any advice appreciated
& thanks 🙏 again for your time making another excellent vid
Thank you. Really well produced video tuition. And I liked your humour🙂
Glad you enjoyed it!
great vid. did not need music but that aside I learnt a lot. Really helpful, packed with tips. Thanks
Glad you enjoyed it!
Great video, very professional mate.I too was shocked at how much those concrete screws gripped.
Thanks
I hope you have a table saw in your new workshop to make that bevel easier. Also you could have drilled your countersunk holes for the fixings before you did the bevel. Would make getting them straight to the brick work easier. Good tip on the order of the countersink. I've made that mistake before
Great to see you using your safety gear!
Always have to else I'll get told off by the Safety Manager!
Great video, your drawings on the whiteboard + explanation were spot on. Thank you.
Thank you
Slight mistake describing the counterbored hole a countersunk one for the bolt head clearance. Brilliant video tho, great to watch step by step with explanations all the way through.
I'll have to remember that!
Very impressed by how it's turned out,. Very good video 👍 well done
I just realised that there's nothing you can't do I will call you in a fortnight to come and do my garden and lots of things including the house alarms 😀