Tutorial: Surface Boarders || Dr Decks

Sdílet
Vložit
  • čas přidán 27. 08. 2024
  • We go over what surface boarders are, how we like to do them, and how to instal them.
    -----------------------------------------------------------------
    Dr Decks Merch: dr-decks.mysho...
    -----------------------------------------------------------------
    Connect with us:
    / drdecks
    www.drdecks.com
    www.therebelca...
    #drdecks #tutorial #surfaceboarders

Komentáře • 24

  • @riflebear1711
    @riflebear1711 Před 2 měsíci +1

    I highly appreciate that rasping for a finished egde. Respect.

  • @deanmccabe8783
    @deanmccabe8783 Před rokem +1

    A dry erase board to show details on the subject your covering? Might be good for us new to this.

  • @BigJohnson1566
    @BigJohnson1566 Před rokem

    Looks good from my house, nice work.

  • @kjbennett7858
    @kjbennett7858 Před 3 lety +5

    Good morning Doc... Could you possibly send me the links for the spacers, G-tape, and your favorite fastening system?

  • @cmcer1995
    @cmcer1995 Před rokem +1

    I see that drdecks doesn't comment back to answer questions which is sad as many questions are spot on and need to be clarified. Attaching the border is fine, but the main decking doesn't have any consistent framework to attach to and support those ends. I guess you have to install another joist.

    • @bash6519
      @bash6519 Před 29 dny +1

      im wondering what would be an allowable overhand for the main decking,. There has to be another joist there for it to break on or at least overhang an inch or so

  • @riflebear1711
    @riflebear1711 Před 2 měsíci

    For a picture framed border with slightly twisted framing underneath that makes the board rock, what do I do to overcome that?

  • @WebbedPete
    @WebbedPete Před 2 lety +3

    Two comments:
    * Borders not Boarders ;) -- unless you have boarders living on the borders 😀
    * What you did NOT show is how you supported the ends of the main decking that butts against the surface border. Are those 3 inch blocks, or does the main deck cantilever past the last joist? And by how much? (I see Azek recommends no more than 1/2" cantilever. My existing decking? They say don't do it, period.)

    • @thatguy1060
      @thatguy1060 Před rokem

      Thanks. I wondered what the hey he could be talking about.

  • @toolbeltconstructionllc

    Dr Decks what is your favorite deck builder forum?

  • @levelseven9841
    @levelseven9841 Před 2 lety +3

    I prefer butt joints over miters, but some customers don't approve.
    Miters are a pain. No matter how tight you make them, once they shrink in the winter, they never grow back to where you set them.
    Don't know why

    • @CMCraftsman
      @CMCraftsman Před 2 měsíci

      You need to pocket screw them from below and use 2P10 glue. I’ve never had a miter open up.

  • @CarlosMUrbaez
    @CarlosMUrbaez Před 2 lety

    what's the impact T torque adapter you are using ? please

  • @Brockthedog315
    @Brockthedog315 Před rokem

    Do you ever show us what the framing looks like before you start Laing these boarders? So far I’ve never seen you do it.

    • @kirstenrussell1012
      @kirstenrussell1012 Před rokem

      Look through the Instagram or earlier videos, there are plenty

  • @donnasaul2069
    @donnasaul2069 Před 2 lety

    Help , I used Deck Screws... the inspector said I used drywall screws...They were not !! So now can add 1 of the simpson LUS28. ...

  • @xyzct
    @xyzct Před 2 lety

    Wait ... I'm confused. Did he flip the board over? AZEK Vintage is only textured on one side. I don't get it.

    • @wazzeradk9398
      @wazzeradk9398 Před rokem

      I think he flipped it end for end.

    • @CMCraftsman
      @CMCraftsman Před 2 měsíci

      Wolf serenity is finished both sides. That’s what he’s using.

  • @tommygun5038
    @tommygun5038 Před rokem +1

    I'm not offended. There's always that urge to overthink things.

  • @loganpatterson4674
    @loganpatterson4674 Před 2 lety

    Surface borders?

    • @KeithWhittingham
      @KeithWhittingham Před 2 lety

      I assume that a surface border is a change of board color or form to create different areas on the deck, or just surround the whole deck

  • @farmermike9262
    @farmermike9262 Před 2 lety +2

    Bro, are you kidding me. This was not a tutorial on surface boarders. Seems like the handful of vids of yours I watched were after thoughts and you do way more explaining than your actually showing. No like or subscribe for you