Nami Burn e headtube shaft/bearing exchange
Vložit
- čas přidán 11. 09. 2024
- In this video you could get the idea and process of
How to replace the headtube bearing,
Assemble the front rotate arm installed with CR40 steel parts, and these two could be done in the same time to service the bearing
All the process needed
The tools could be purchased from my side
tool for disassemble the bearing cup,
tool for install the bearing cup,
tool for lock the bearing nut.
Other video shows to remove the original shaft by cutting it off is in the chanel as well in the link below
• Front wheel rotate arm...
More information is linked into the facebook post
/ 1158903444789040
My email is shataofahm@hotmail.com for more information if needed
Thank you for the video. Just feedback -> My brand new Nami burn-e 2 max 40Ah with the newest LED lights and reinforced frame just developed a steering notch just after 500km of ride.
I am not a heavy rider just 85kg, and I didn't ride it in the rain, so not sure why this is happening on the model that should be "problem-free" . Well, I guess lets buy some tools and let's have "fun" with it. Otherwise, the scooter is very good :)
Should probably use bearing packer. Pasting grease only on the outside like that will probably cause notches problem we're all familiar with.
thanks for all this golden information!!!!
Aluminum one is black? New new one is steel silver?
Correct
Since when is the alumium ones been replaced with the upgraded steel version from the factory? I just ordered burn e 2 28Ah version and wondering do i have to replace the shaft.
it is not needed for replace unless you have a accident before on the unit, a crash or a bad hit
or you just worry about it
Hi Michael Sha,Quick question for you sir...I got this spring a 40Ah version and I notice sometimes that when I turn my steering wheel is not moving smoothly as I turn but in increments such like a pre-set position which cause me to feel like I don't have a controlled turning of the steering and causing an imbalance in the ride...Do you think that this is a sign that I need to change the bearings...again this problem is showing only sometimes.Thank you and looking forward for your clarification!
you could do a service to the bearing, and re grease it. most likely the bearing should be fine
Thank you very much Michael…will do it when I will take the scooter for service
Michael I bought the 72v 40ah model. How long should I take to change the bearings? at times the steering wheel became very hard, and I just loosened it a little with the special wrench, and the steering wheel became light, but before that it seemed to me that when turning the steering wheel it stuck, I thought that the bearing had broken.
When are the upgraded versions of the Burne MAX (Stem, NFC and Indicators) being shipped to Australia?
EDIT: I contacted Michael via email and he replied very quickly and said he believed they are already being shipped, but I should check with my dealer. I did exactly that and it turns out they are here and have the upgrades which is awesome!!! (as of 7th October 2023) Hopefully I should have it in a week.
Hello Michael,
When did you start to build in all the update parts?
Ordered a Burn E2 Max 40AH and it is from 04.2023. It is currently on the way from CN to EU. Do i already have all the updated parts that you showed here intalled?
I will open the motors and coat them with ECS 71 Urethane before drivind around. I will probably also make holes so moisture and water can get out of the motors.
Are the motor temp sensors installed on the hottest spots on the motors?
I have the Same Answer please Michael Sha Talk with us 😂
Question*
@@emilio13 i read on facebook that the ones produced in 2023 have already updated the stem but i am not sure if everything is updated. 🤔
no answer = no it is not 😨?
Okei when I Buy a New Burn E 2 Max 40Ah is it possible that the steel stem New bearings ist also installed (2023Charge)
Haha u using the tool I used bud must of been my pic that influenced ya
It's not as easy as you make it look.
Thank you for the video. The two silver rings which hold the bearings are upgraded or just the same as old ones? Can we keep old rings and replace only the bearings?
No
Sir good morning Do you sell a
C spanner to remove the bearings?
yes
@@michaelsha2781 where can i Order with head set and bearings
My model is aluminum, do I have to change to this new one in iron?
i suggest you make the change if you had a crash or hit something in high speed before
Where can I order this upgrade, I have seen it online but not sure if it's a copy or not, if you could be so kind as to send me that information. Thanks
There is a link for the Facebook post which have all the information, read it and you will know how to order and where to send payment and what info to provide
Link of post is in the description
Hi Mr Sha. I have a new Nami Klima… Do I need these parts too? Klima is awesome Scooter thank you sir!
no, only for some of the burn if you have concern
hi..Klima has this new one allready ? thx
Yes
Can I send my scooter back to get repaired
Problem I have 😢
Can u make a video how u weld frame?)
Why do i do that t
"Promo sm"
Come on ..where to find that tools Im paint sprayer not mehanic...Looks easy to you and probably 60 procent people can do that,me also just if find tool..
contact me for tool if needed