How to Wrap Your Car's Spoiler with Vinyl
Vložit
- čas přidán 6. 09. 2024
- In this video, you're going to see how to wrap the spoiler on a hatchback using tools and material from Rvinyl available here:
www.rvinyl.com...
The first step is cleaning: take a tucking tool and run it along all the edges using Rapid Prep. Make sure you do a full 360 is cleaning those edges is absolutely critical for long term hold. Once the 360 is made, then it's time to clean the main surface and masking tape the outside edge. The masking tape will lower the surface energy and allow the film to be tucked deep inside these gaps safely without being overstretched.
Once all the masking tape on one edge, a setup, do the exact same thing for the other side if applicable. Here there's a tight gap so the masking tape being placed over the black molding which will allow the film to be picked up and tucked in nice and deep without overstretching. Here, the antenna is slightly in the way of the main piece, so it's being cut safely away ahead of time so the material can lay flat. This will help with workflow. Now that the material set simply fold of one half over and release the liner. In most cases because premium film is used, the material will be able to slide and glide across the surface so you can remove a large section of the wrapping film tack it onto the surface, then pull the entire liner off.
Pull the film evenly toward the other side. And now it's time to create 100 percent glass, which means a wrinkle free surface because if there's too many wrinkles on the surface and on the edges it can lead to overstretching and low quality. So here the film is stretched evenly away from the corner and then it stretched evenly with two hands pointing in what's called the triangle shape. So by spreading the film out by pulling it 45 degree angles from either side, this creates that glass like shape on the surface.
Once glass has been achieved, is always a good idea to add heat just to relax the film. This will shrink it slightly, so it'll keep it from overstretching once it's tacked on. Always apply the recessed areas first with an application glove, then take the squeegee that has a monkey strip corner with a felt buffer on it. This means the film can be taken safely to the surface and won't be scratched tech in one body line first, then squeegee the main flat area with firm, overlapping squeegee strokes. The film has what's called air-egress features on it, which means the air will float nice and even underneath the film. So this means no bubbles and high workflow. You can see with overlapping strokes, the process, once the film is glassed out, is easy and straightforward.
Now it's time to pick the film up and tuck it into any gaps, so here the material can safely slide off the masking tape and be tucked deep into the gap. This is for full coverage and hold. Then once everything's tucked in and set on a finger on the outside edge to double check for any attention and check for bubbles.
Now it's time to add heat. This activates the adhesive. So do a 360. And while doing this, look for any loose edges. It's very important that the film is 100 percent up before we get into the cutting process. Always click the blade, so it's extra sharp and for this particular cut is called a tuck and cut because the molding at the bottom tightly fits in with the spoiler at the top, the blade could be safely held in the groove. Make sure the angle of the blade is roughly 10 degrees towards the edge and keeps the knife at a 45 degree angle. Once the cut is made, come in with an Avery Dennison Flextreme and seal the edge.
So by running alongside the edge, it stays nice and straight and gives just enough material to wrap around the edge, which is then sealed with an application of what's one section is done, repeat the same for the rest of the top of the spoiler angled blade slightly away. So the film wraps around and keep that blade edge alongside the edge of the spoiler. Come back and seal the deal with a buffer in the squeegee. Remove the masking tape and repeat the exact same steps for the other half. It's all about having good body position, so never cut away from yourself, always cut to yourself and have a nice light touch. Once cut, retract the blade for safety, pull away the excess film low and flat away from the spoiler, and then immediately come back and seal the deal with the evidence in Flexin.
With everything cut out, the final step is to go over the entire hatchbacks spolier with a heat gun, this is to double check for bubbles, activate that adhesive and make sure 100 percent of those edges are nice and tight. Be extra thorough during this process. Also, if there's slight dull scratches on the surface, they'll be self healed with the heat. And then the final step is to wipe the spoiler down and remove any handprints and it's ready to go.
#Rvinyl #SpoilerWrap #HowtoWrap
What film would you use on your spoilers?
what is the name of the blue tap is that?
How many feet of vinyl wrap is needed to wrap a 350z spoiler like the Vader 3?
hey thanks
You're welcome!
Is it easy to remove? Would like to wrap my bike.
Dan, Yes it can be removed without damaging your bike. It is a bit of a pain, the adhesive has to be strong enough to stay in place. You can get an idea of the removal process here: www.rvinyl.com/how-to-remove-vinyl
What about underneath
Our apologies for the late reply. You want to wrap the underside of the hood? This area is not usually suitable for wrap as it is often left unfinished.
Was i wasnt clear meant underneath the spoiler
@@celestinoprien3387 Our apologies. Since it isn't going to be easily visible, they didn't wrap that part although they could have. Once issue would be longevity hanging like that almost parallel to the ground.
How much wrap would it take do the stock spoiler on a 2000 mustang?