I've been using Acrylic devices or a few years now. From amplified units to pre amp units. I've also updated century old radio to s remote streaming radio. The unit to unit integration is fantastic. Pressing pause on one unit and play on another in a different room continues the music to whatever room you are sitting in.
I have two of these, and most issues I had have been resolved in a recent firmware update. However although they both work ok, the quality of the white LEDs is not great. They are both used mainly on the ARC input, on one unit the ARC LED is no so dim you can hardly see it, and the other unit, it's completely dead. All the other ones light up ok when you change input. On one of the units, the BT LED is also getting pretty dim. Just the white LEDs, the red Stby one is just the same as ever.
I am using a HP laptop I5 as source. HDMI out to tv HDMI in (non-smart tv). The Arylic connects from laptop by a USB C port to PC input on Arylic and Shows on unit display as DAC.
Hello,thanks for your video. One questione please. It's possibile connect the BP50 to the aux input of and integrated amplifier? Or I can use It only with a Power AMP? Thanks so much Diego
Hello 12VVids, I have a question that so far the gurus of turntables cannot give an answer too!! I saw that ground lug screw the pre amp and it came to mind again. My NAD 7400 power cord is not grounded, it is just a standard two prong 117v plug for the US. Can I ground my turntable to Earth Ground, the center screw of the outlet ?? Is there a reason that I should not need it? I have no hum connected to the ground lug of the NAD. Just a curious question. Thanks Bryan in EL Paso:)
Ground wire goes from tone arm ground to chassis of amplifier or preamp. Some turn tables ground this to the audio cable and thus won't have a separate wire.
I am on my 3rd Arylic BP50 and they all are doing the same thing. Randomly no sound so I have to rest or turn off and back on then it is fine. Just never know when it will cut off sound. Funny thing the sub out still works when the sound goes out. Any Ideas ? This happens on all outputs.
I am using a HP laptop I5 as source. HDMI out to tv HDMI in (non-smart tv). The Arylic connects from laptop by a USB C port to PC input on Arylic and Shows on unit display as DAC.
Replying to old comment, I have two BP50s that had this issue, there is now a firmware update to version 57 as of writing which resolved the issue on both.
I've been using Acrylic devices or a few years now. From amplified units to pre amp units. I've also updated century old radio to s remote streaming radio. The unit to unit integration is fantastic. Pressing pause on one unit and play on another in a different room continues the music to whatever room you are sitting in.
I have many running here and sold a few spares. All work great.
They have nice Bookshelves speakers as well. Excellent compact components for the beginner.❤
I have two of these, and most issues I had have been resolved in a recent firmware update. However although they both work ok, the quality of the white LEDs is not great. They are both used mainly on the ARC input, on one unit the ARC LED is no so dim you can hardly see it, and the other unit, it's completely dead. All the other ones light up ok when you change input. On one of the units, the BT LED is also getting pretty dim.
Just the white LEDs, the red Stby one is just the same as ever.
ESS ES9023P. Excellent DAC btw.
Yes
Nice tunes you got there.
I am using a HP laptop I5 as source. HDMI out to tv HDMI in (non-smart tv). The Arylic connects from laptop by a USB C port to PC input on Arylic and Shows on unit display as DAC.
Is DAC of good quality?
Hello,thanks for your video.
One questione please.
It's possibile connect the BP50 to the aux input of and integrated amplifier?
Or I can use It only with a Power AMP?
Thanks so much
Diego
Yes, you can
handy device to use best on an older stereo set up
Can you acces the music on the usb stick from your phone?
Never tried but I will say no.
Last week i bought one but ARC is not working on my setup. Tried everything but till now no succes. Anyone any suggestions?
Can I connect this to my Hegel Amp so I can receive and play the bluetooth signal coming from my audio-technica lp60 bluetooth turntable?
It has audio outputs so if your amp has audio inputs then yes
Hi! Can you tell me if the BP50 preamp will take the BT signal from (not to) my laptop to the preamp?
Yes
Hello 12VVids, I have a question that so far the gurus of turntables cannot give an answer too!! I saw that ground lug screw the pre amp and it came to mind again. My NAD 7400 power cord is not grounded, it is just a standard two prong 117v plug for the US. Can I ground my turntable to Earth Ground, the center screw of the outlet ?? Is there a reason that I should not need it? I have no hum connected to the ground lug of the NAD. Just a curious question. Thanks Bryan in EL Paso:)
Ground wire goes from tone arm ground to chassis of amplifier or preamp. Some turn tables ground this to the audio cable and thus won't have a separate wire.
Thank you for the info!!! :) @@12voltvids
I am on my 3rd Arylic BP50 and they all are doing the same thing. Randomly no sound so I have to rest or turn off and back on then it is fine. Just never know when it will cut off sound. Funny thing the sub out still works when the sound goes out. Any Ideas ? This happens on all outputs.
Never have had any issues with any of mine
I am using a HP laptop I5 as source. HDMI out to tv HDMI in (non-smart tv). The Arylic connects from laptop by a USB C port to PC input on Arylic and Shows on unit display as DAC.
Replying to old comment, I have two BP50s that had this issue, there is now a firmware update to version 57 as of writing which resolved the issue on both.
Nice app very responsive
seems only a US product wonder what like this in UK
I know this is an old comment, Arylic now have an outlet on Amazon UK, I've purchased two BP50s from there without issue.