A1 Recall Full Bed Replacement Video - Including the mandatory pictures for the Bambu Coupon

Join this channel to get access to perks:
/ @micbot
00:10 Intro
01:40 Pre-installation checklist
Old Bed Removal
02:21 Step 1+2 - Bed removal
04:05 Step 3 - Place Printer on its side
05:15 Step 4 - Disconnect gray box and wires
06:20 Step 5 - Remove Plastic Panels
07:20 Step 6 - Disconnect Power, ground and 4 pin cables
10:00 Step 7 - Route the old cables out of the printer and remove the old bed
New Bed Install
10:56 Step 1 - Place Printer upwards
11:10 Step 2 - Align and install new bed
12:00 Step 3 - Place Printer on its side
12:45 Step 4 - Route and connect the new bed cables
15:26 Mandatory Photo 1 - Secured 4pin cable
16:35 Mandatory Photo 2 - Ground wire secured
16:49 Step 5 - Reinstall the front back panel
18:00 Step 6 - Lock the heat bed cable
18:41 Optional Photo 1 - Locked Cable
19:00 Rear Panel Install
19:37 Step 7 - Reinstall and wire gray box
20:30 Step 8 - Install Backstop
21:05 Mandatory Photo 3 - Backstop
21:25 Photo Review
21:49 Test
Patreon: / micbot
LinkTree - 3D Printing Deals Coupons and more: linktr.ee/micbot
My 3D files and creations on Cults3D:
cults3d.com/en/users/MicB0t/c...
Anycubic Links:
M5s Pro: amzn.to/49sjFAl
M5s: amzn.to/49PDtgM
M5: amzn.to/4bO2nyZ
Wash and cure 3.0 Plus: amzn.to/48qXtFr
Wash and /cure 3.0: amzn.to/4bQw6Yc
M5s/Pro Screen Protectors: amzn.to/4c35eEy
M5s FEP Release Film (not ACF): amzn.to/3P04FBn
Resin: amzn.to/3SW935u
High Speed Resin: amzn.to/48wlYRp
Spare VAT: amzn.to/3TcNr6c
Resin Silicone Slap Mat: amzn.to/3TeblgL
Resin Filers: amzn.to/49QSDm2
ISOA 99.9%: amzn.to/48uZD6P
My Printers:
AnyCubic M5s: amzn.to/49kYsbb
AnyCubic M5: amzn.to/3uIpZ7v
AnyCubic Wash and Cure Station 3: amzn.to/3I7FcSQ
Ankermake Products: shrsl.com/4ee47
Creality Products: shrsl.com/4ee97
Anker Make M5C - amzn.to/3udY538
AnkerMake M5 - Canada: amzn.to/3kTrqeD / USA: amzn.to/3M1GFx8
AnkerMake Filament: amzn.to/3HLixv6
Creality Ender 5 Pro - Canada: amzn.to/3wM18Nn USA: amzn.to/42ZTvlI
Ender 5 Pro S1 - USA: amzn.to/3Zz8CiK
Creality Ender 3 - USA: amzn.to/3m4RsMh
Creality Ender 3 S1 - USA: amzn.to/3zlmLp9
AnkerMake M5 Link: amzn.to/3qjNWzp

[@glensmith-or1bp]

Going to tram mine just wondering if your planning a video. TYIA

[@MicBot]

Thanks for watching! Yes, I will make one this week.

[@glensmith-or1bp]

I finished my traming portion yesterday following the video off Bambu’s site via Ricky Impey’s site. But really wanted to post your video was very very precise and clear to follow so happy to report the bed change was perfect. Thank you very much it was a bit more than I expected and could of went bad but your tips I followed to the T! Again thanks a bunch already sent the photos in to Bambu.

[@MicBot]

Thank you for the kind words 😊