Video není dostupné.
Omlouváme se.
Softail street bob front undermount Led indicators
Vložit
- čas přidán 18. 01. 2020
- Quick video installing the Brown Industries undermount Led indicators on my 2019 Harley Davidson Softail street bob
Music:
Intro/Outro:
EDMUR QUINN - "RUNNING MAN" HARD 808 TYPE BEAT | No Copyright Trap
• EDMUR QUINN - "RUNNING...
Free Download Link
bit.ly/2URUipq
1st tune:
ƁƝƁ Productions
EME BEATS - "YANG" FREE TRAP BEAT | No Copyright Trap
• EME BEATS - "YANG" FRE...
SUPPORT TO:
EME BEATS
www.youtube.co....
/ eme_beats
Perform the LED Sync process:
-Turn ignition power ON (do not start bike)
-Turn 4 way hazard flashers ON
-Turn ignition power OFF
-Let hazard flashers run for 3 minutes
-Turn ignition power back ON
-Turn 4 way hazard flashers OFF
That worked perfect to mine FXBB 2018.
If that doesn't work, a load balancer will. The hyper flash is due to the reduced draw by the led signals, which causes the computer to think there is a problem.
Just a quick tip dude, when using heat shrink, you can use the fat barrel part of the soldering iron to shrink it instead of a lighter. 😊
Really helpful man! I just got these for my Fat Bob and was really hoping someone posted a step by step starting with disconnecting the stock Christmas tree ornaments.
Great to hear the vid was able to help you mate 👍👍
Hubby had the same issues hyperflashin with the SikTail he installed on his M8 Breakout, easy fix was to install CanBus Load equalizer pretty much screw them on and they are done, clear your codes and away you go, an easy investment of $8 each he needed 4 of them, he did a short video on my site, i ordered the same and got the load equalisers through our dealer and they are available online, cheers
I'm not entirely sure if it makes a difference because your signals are soldered but these are the instructions we had to use to get the indicators to stop blinking fast to on my brothers 2019 Harley Davidson Street bob. Hope this helps!
The BCM can self-learn once LED turn signals are installed if Hazards are active
after installation.
• Turn the ignition ON. Activate 4-way Hazards. Turn the ignition OFF and let the Hazards run for 3 minutes. Turn the
ignition back ON and turn off the 4-way Hazards. Turn the ignition OFF and then back ON.
• Check for proper turn signal operation in all modes. You may need to repeat the procedure if the turn signals still flash
rapidly.
Thanks for the tip brother I'll definantly try that one out 🤙
@@TheGingybeardMan did that work?
@@DTH8220 my bike didn't have any luck with that method.
Good job 👍🏼... but I like the stock indicators ... replaced by the white LED’s, since they stay on, more lights at night the better ...
Just fitted some of these on my 2021 Streetbob turn ign on put 4ways on turn off ign leave 4ways on for about 5 minutes then try it worked on mine
from a dust storm to pouring rain... Thx for the video
No complaints. Looks sleeker and definitely ties in with the overall look. As for the dust storm...damn
Thanks mate, I know the dust storm was like something straight out of mad max fury road 🤣🤣🤣
Bruh that Chewbacca scared tf outta me, but thanks for the post just got these and saw no videos on the install so thanks!
😂😂😂 super loud hey
I disconnected the front signal plugs and just the rears worked.. then I cut the wires beside the front lights now only 1 rear works
Congratulations on your rain!
I’m looking at getting a 2021 street bob and these videos help out a lot thanks keep it up my man
Thanks man, Hope you get the bike mate 👍
I did the same thing with my fat bob and I also had the quick flashing indicator. I found out that it is because the ecu sets a DTC for both front turn signals shorted all you have to do is clear the DTC's and it will work normal. Also if you have a fuel pack tuner you can also clear codes that way. That is How I got my signal indicator to flash properly. hope this helps.
Hi mate,
I’ve the same issue on my 2010 nightster. I have a fuel pack tuner, how do I clear the codes or does it need to go to a garage?
Cheers
Joe
Had samekinds in my 06 softail many years. It need resistor to work propebly.
Hi mate. Very cool and clear video. I didn't know how to do, I follow your steps, and everthing is ok. Big thank from France ;) I installed Heinz Bikes led indicators which are very similar to the ones from the video.
I still fail to fix the fast signal, while indicator are ok.
To fix the fast flash on the gauge you need to install load equalisers 👍
nice job man, I do like those 💯👍
Sweet vid, the indicators look great 👊
Thanks man 👍
Harley has a similar looking one brand Bailey. Is there any difference?
That’s beauty .
Who ever was the guy who disliked this video is a coward .
Ahhh can't please em all, trolls be trollen 🤣🤣🤣
Haha that’s is true brotha .
Cool man just about to throw some on my FatBob
I used to put my mirrors on upside down too but would put the left on the right and right on the left for a better fit ✌️
Looks great ah!, 😎 I've got them on my 19 SG. Alot better than the stockies. Oh yeah, we finally got rain up in the hunter too, forgot what rain looked like 😳🤔
Good vid mate.
Thanks mate, yeah they look so much better than the stock ones 🤙🤙. Here's to hoping for some more rain 🙏🤞
Amen to that. 🤞
Im installing led mini indicators on my 2016 breakout fxsb and notice the bike has 3 wires purple which is the power and a black which is ground wire and a blue which is the daytime running power. Now my question is the mini indicator only has 2 wires a red and a black. Do i need to make sure the daytime running wire is connected or can i just forget about it? Any feedback would be good thanks.
did you figure out which wire goes with which?
Any problems with that turn lights? Does it light up the read light on the panel? Any error code?
No problem at all and no error code. If you don't install resistors the indicator panel will just blink a little faster than usual. The actual blinkers themselves don't blink any faster than normal.
For anyone looking for some of these drag specialties makes some. I ordered from Dennis kirk.
Search "drag specialties handlebar mount signals"
Good job. Form FXBB thailand.
Another great concise diy vidy with no over enthusiastic presentation (thank Christ for that) stretching it out to get more adverts in or requests for likes & subs so I gave you a like & hit the sub button top job.
Cheers mate, appreciate it 👍
Gingybeard that sanding block deserves a bonus ;-) , the indicator male plug has the purple n black wires same as UK 1156 , has the main wire loom female plug a blue always live ? as im thinking of changing the 1156 turn housing to a 1157 housing . cheers
Soul purpose for its existence 🤣🤣🤣
Drag specialist are not that dear and brighter
Actually good point. I wasn't aware of those 👍
When I change the 💡 out of mine they quickly flash like that to but the light still blinks normal don’t know what’s going on but I don’t mind it
thats because the BUS Communications needs another resistance, else it will display this error.
Nice! Peace n Luv from Minnesota
Thanks brother 🤙🤙
Mate what resistor did you use and where is it located? I have Kellerman Atto DF 3 in 1 rear indicators, and Atto DF front indicators to fit. I know I need to fit a resistor but don’t know where. Cheers pal.
Hey mate I still haven't purchased any resistors for the indicators. I do plan on installing resistors in the future.
What mirrors are those
They're the stock mirrors flipped upside down
To fix kick flashing you must juste put WARNINGS ON, put th contact OFF, wait 3 minutes with warnings ON and after stop warnings and that's all. I did it westerday.
I purchased the Ciro Fang led inserts. I needed to re-cable entirely cause the led indicators have a extra function (stays on with the main light) and therefore three/3 wires) #justsaying
The Australian model lights do not have a running light which stays on with the blinkers. Hence our models only have two wires
Those nuts that connected the original blinkers, are they stock ?
It was that long ago man I honestly can't remember
Did you fit load equalisers to the front indicators to remove the quick flashing issue?
No not yet, I plan on getting around to it one day
God mate your good at doing stuff on ya bike. 👌👌👌👌👌
Thanks man, I almost enjoy working on it more than riding it 🤣🤣🤣
@@TheGingybeardMan well it keeps u busy out of trouble lol.
@@TheGingybeardMan are u a mechanic?
@@deanwicks3940 no brother, just a bloke who likes working on his bike 🤙🤙🤙
Looks trick👌. Under tank, usb box removal mod next??, haha
Hahaha thanks bro
finally, some nice videos of Street Bob 2019.
didn't you have to install the equaliser to fit the LED direction indicators?
I didn't have to for them to work as the company stated I didn't need to. I will however install some in the future to stop the fast slashing on the gauge 👍
The Gingybeard Man did you fit the Resistor to change the speed of the flashing? If so was it easy and where is the Resistor sat?
Awesome job man! Loving the digital dash.. where is this from?
Thanks man. The digital guage comes stock on the softail street bobs.
Nice job, just did this mod yesterday. Your vid was helpfull. Did you manage to fix the speedy turnsignal light?
Thanks mate. I havnt fixed the fast blink as it doesn't bother me, all it requires is some load resistors installed.
@@TheGingybeardMan ah ok, I think I'll go the same route. Although I have to fix something. My left side turnsignals won't come in. Hazard switch works all 4 lights, rightside works also, but not the left...
$15 shipped from ebay
Did you need a load equaliser mate ?
The indicators will function properly without one but a load equaliser will stop the fast flash on the indicator panel
Hey bro where did u get ur headlight fairing and digital speedo cover from?
I bought the fairing from Memphis shades and the digital guage mount off a website called get lowered 👍
looks good crazy expensive for 2 little lights
100% I agree stupid expensive
Putting these on right now... I have 3 wires going to my stock turn signals: purple black and blue.... Think I should run the purple and blue together into the purple after stock wire??
Mate I only had two wires to wire up for mine. I presume your third wire is for running lights on your stock indicators. Is your Harley an Aus or U.S model. Our Aus models dnt have running lights in the indicators.
@@TheGingybeardMan American... Yep sure is running lights. So when I hook up both blue and purple together, I have running lights but then no blinkers. If I I just run the purple, no running lights but I have blinkers. And mine is doing the same thing yours is with the fast blinking on the dash. Thanks again for your quick replies bro.
@@behindthehandofdoom these brown industries indicators arnt suited for the running lights. So you can only run the blinkers with the purple and black wires. With the fast blinking you will need to install some resistors. It's no big deal and doesn't really bother me, so I havnt got around to it yet.
@@TheGingybeardMan what should we do with the blue wire? (Constant running)
@@behindthehandofdoom what did you end up doing with the blue wire??
Slick mate 🤙🤙🇳🇿🇳🇿
Cheers brother 👍
Hey mate , I actually have the same front brown industries indicators and also the same rear wunderkind leds as you . Both are great however , I have the same issue as you with the fast blinking dash light . You will also find that when you cycle through your diagnostics the BCM fault codes come up B2146c and B2141c which translates to both front right and left signal is open . There is no fault on the rear as they were originally leds . Jus the front two . I’ve tried the hazard light sync method an no win yet . I’m guessing a load equaliser will fix it but if you have found anything that worked to fix let me know . Cheers MH . 2018 FXFBS
Not yet mate I havnt bothered trying to fix it. I've also tried the hazard light sync with no luck. I'd say load equalisers are what's needed 👍
@@TheGingybeardMan Hi, Did You figure it out what to do with a fast blinking dash light? I have got also (same as Mark H) BCM fault code B2146c and B2141c. I've tried also the hazard light sync method with no luck. Probably load equlizers will solve the problem, but it shouldn't be nedded as the CAN BUS have a selflearning system. Also, if selflearning system doesn't work the turn light itself should blink fast but the same like on your bike on mine it flash normally.
Hey man what size did you get the sheild stickers made in? I like the look of those instead of the stock badges.
Hey mate I had my wife make the tank decals on a cricut machine. The dimensions are 10.7cm X 7.5cm 👍
@@TheGingybeardMan I appreciate that my dude. I've been following you for awhile. Just used your t bar video yesterday to do it on mine. Very helpful.
@@TheJdubb75785757 cheers for following the channel mate 👍glad to hear the vid helped you out 🤙🤙🤙
Where can i get this indicator?
From this website mate.
wunderkind-custom.com/en/motorcycle-accessories-shop-details/237/led-indicator-rear/136/indicator-taillight-combination-2stripes-for-fender-
LED’s looks great!! So how you liking the new Cams.?
Thanks man, yeah I'm really diggen the torque cam, it's definantly a noticeable change in power but nothing crazy 👌
The Gingybeard Man Cool good to hear that you love it!
I’ll putting the Stage ll SE-585 cams on my 16 FLSS soon can’t wait..
@@fililoboesparza5784 nice man 👍 let me know how those cams perform on the softail slim S
Where did you get your tank emblems at? I'm gonna remove my stock ones.
My wife made them with a cricut machine. If you have a look on my channel I did a vid on it 👍
Any recifiers needs due to the leds?
The indicators will work without resistors however there will be fast flashing on your indicator panel if you dnt install resistors
@@TheGingybeardMan yeah not fused about that lol
Bro if sons of anarchy came back you would be on the show !!! Keep up the mods on street bob !
Cheers mate, still have a load of things to be done to the bike 🤙🤙🤙
you should link the products you buy!!
Hey buddy can you send me a link for those???
Hey mate, unfortunately they're only advertised on their Facebook account and you can only place an order via a telephone call. Their Phone number is (02) 4954 4436 and the Facebook account is m.facebook.com/newcastleharleys/
those are cool but I like my running lights
Yeah the Australian Harleys don't have running lights built in the indicators.
The Gingybeard Man good videos man I watch them all. Always waiting for the next keep em coming brother.
@@blkfxbb327 thanks for the awesome feed back and for following my channel mate, I really do appreciate it 👍
Try keeping the hazards on for longer....at least three minutes. Should do the trick. 30 seconds isnt long enough.
Will do mate 👍 I'll let ya know how I get on
cheers lads we stock them online @ www.westcoastgarage.com.au
Sik AF
Stock are better