Lexus LS400 Wiring Harness Tuck (Without Removing Fenders!) - 1UZFE V8
Vložit
- čas přidán 26. 08. 2024
- What's up big girls. Today we show you how to do a wiring harness tuck on a Lexus LS400.
If the video was helpful, please like it and consider subscribing!!
Link to Subscribe:
/ @biggirlsgarage8331
Also Check Us Out on Instagram and Tik Tok!!!
Music:
Cloud (Prod. by Lukrembo)
#biggirlsgarage #BGG #Lexus #LS400 - Auta a dopravní prostředky
Why isn't this more commonly known about? I was literally about to spend hours removing the fenders, trim pieces and lights to tuck my harness', and all I need to do is take out the liners and drill holes.... you are a life saver!
I was going to do the same, but I looked under there and figured I had enough room to make it work. Not sure why everyone does it the complicated way. Good luck!
Just finished doing both harness’ about 15 minutes ago, still a ball ache because of all the bolts that hold on the arch liner, but I saved so much time avoiding the fenders because of you 😂 thanks again mate
No bro don’t do it do it the right way there’s a reason we take the fenders off these guys are lazy and obviously don’t care about the car
@@dylankeepers2064 why
@@dylankeepers2064 yeah why? What makes this wrong
Bro jus saved me from spending a couple hours taking the front of my car apart😂😂greatly appreciated to you my good sir💯
Great to hear! Maybe you should subscribe as a form of gratitude ;)
Legend bless up for this video R.I.P Kobe tho fr
Respect and love
Woohoo, good job boys!
hahah the oblivion scene so good
A gentleman of culture. Show love
If i have ever seen a good tutorial with great jokes, this is IT!
There are no jokes. Only passion.
Your Genius is showing 👀
Intelligence is the new sexy
I plan on doing this today. Wish me luck 😅
Best of luck warrior
Do u have to tuck both driver and passenger side?? Wish I would've have seen this before I did driver side this morning 😭😭
Yeah you have to tuck both of them, way easier to not take off the fender haha 👍
- Shawn
Be thankful you did it the right way bro this was butchered
@@dylankeepers2064 how was this butchered?? Seems like you're just butt hurt you took your fender off and didn't do it this way. Not saying that way isnt a good route!! I rerouted mine through the engine bay on my sc300 and I'll probably do it this way on my ls400.. There is no harm to the wires or anything wrong with this way that I can see. Unless you're seeing otherwise?
Lmao that intro 🤣🤣
Very saucy
Saucy just for you
Did you still have to cut notches? Or where did you put the harness through?
much appreciated
You had me at chungus
A Man of culture i see
@@biggirlsgarage8331 ( ͡° ͜ʖ ͡°)
Always see vids on the wire harness but nobody ever says anything about the thick layer of metal that can potentially cut into the tire lol. I’m tryna find an alternative other than using a grinder and shaving it down
You can get rubber edging to slip onto the sharp edges. Another way to do it is to cut a slit lengthwise down a small rubber hose and slip that on
I ended up grinding it down and smoothing it out @@areitu
I don't see how this is much different than the 'right way' besides the fact that you're drilling into the frame, which exposes some bare metal and will rust over time.
If I go this route, I'll probably hit those holes with a few coats of rust preventative paint... but other than that it looks like a perfectly acceptable way to go.
Its easier. If done properly shouldn't create any issues
Same process for drivers side ?
Yessir. The wiring looks a little bit different but it is the same process. Good luck.
Have you had any issues so far driving with it like this ? Doing this tomorrow
None whatsoever
@@biggirlsgarage8331how about now? Still holding up good? Also how low are you
Why does dylan think this is butchered and not correct? Have you had any issues at all? Do you drift ur ls?
Never drifted it, no issues, who's Dylan?
Did this last??
Yes, we sold the car. But we assume it has lasted since.
@@biggirlsgarage8331 genuinely appreciate the reply gonna do this now, i got bcs ready to install tomorrow and this had me stressing a bit
Good luck!@@1uzpete
How hard is takin off the fender liner
Just a couple of bolts, few clips and a subscribe button to click ;)
@@biggirlsgarage8331 did it today hella easy bless
@@ribhi1864
fuck me, where was your video earlier, I literally just came back from removing my fenders and putting everything on, and nothing alligned like it was before lol
Oof that’s tuff
I legit remove my fenders in less than 5 minutes it isnt that complicated
It's always nice to have a 2nd option though. 👍
Love and respect
Respec and love