How to Calibrate an ESC in less than 5 Minutes (2020)
Vložit
- čas přidán 4. 09. 2024
- Failing to calibrate your ESCs can cause your drone to fly funny, if it even flies at all. Learn how to calibrate your electronic speed controllers.
The RC controller used for this ESC calibration is the FlySky FS-T6
If you would like to build this Raspberry Pi drone, the parts list can be found below:
dojofordrones....
If you'd like a full 6 hour curriculum to jumpstart your drone engineering learning path, check out this course!
-
---
-----
dojofordrones....
-----
---
-
Seriously this is the ONLY way that worked for me thank you man! My setup: Pixhawk 2.4.8/ hobbywing xrotor 40A esc/ Racerstar 3508 motors
I was scared but it was so simple, thanks dude, have a really nice day
That was under 3 minutes. Thanks pretty straight forward.
Thanks a lot, you are easy to follow.
Thank you very much! Great explanation!!
just what i'm looking for, the best.
Thank you
It’s help me so much
I am fro Kuwait 🇰🇼
my new esc wont double beep, just keeps single beeping every few seconds, anyone know why?
Im assuming its just a shoddy esc
Thank you very much for this video I almost got a headache with my rc boat lol
Haha glad the video helped you! I've certainly been there
Thank you
really helping THANKYOU so much 🙏
Great video!
Thank you!! Glad it helped :)
Please help: We are new to RC aircraft, and we are stuck on this process.
After following your calibration instructions step by step, we move the throttle up slightly and then the motor jerks and stops then beeps 3 times as if it's confirming the calibration again. When I push the throttle up again, it jerks again and repeats the process. If you leave the throttle up, it beeps non-stop like a warning.
What could be wrong?
Thanks in advance.
How to calibrate my Holybro QAV250 pix23 v6
but without having a joystick ?
is it possible ? if yes, please gave me some hints to start searching
Thank so much. jajakallah khairan
Thank you very much!
Tq sir this trick is working, 👍👍😋🙏
Thank you man love you
Thank you 😀
No problem!
Thanks you solved ma problem.
Ding ding😂 nice job😅👌🏻
Thankyou sir, But should I do this process again to the other 3esc? or I need to connect all of them and do it once?
Could you explain as to why does it happen though? Like why sometimes ESC causes the scenario where you give half the throttle and then it starts..
How can I recalibrate my hobby queen brushless ESC it’s for a RC car and my motor is not even moving hardly any needs to be recalibrated I was trying to find a video on CZcams but need some help does this process work for any ESC
Can anyone help, my esc just keeps continuously beeping
Are you turning it on before the controller?
THANK YOU!
Im not hearing any beeps after plugging in the batterie. Could a bad motor stop the esc from calibraying?
Very good .
I will give it a try.
I've been working on a 1:32 scale touring car with a 10 amp drone esc.
I got it to work, but not properly.
One other thing. I'm not using a flight board. I dont know if that will make a difference.
Any suggestions would be helpful.
Thank you.
while trying to calibrate my 2 ESC they don't create those 2 ding sound and after that three . SO unable to calibrate any other issue which i can check ?
Hi! Great video! How would I do this with a pistol grip controller? I have an austar AX5S connected to a generic brushless 40a esc. Any help would be greatly appreciated! Thank you sir!
Can we recalibrate esc s