Remote Water and Gas Metering with the EKM Push Data System

This video is is an introduction to pulse counting with EKM Metering water and gas meters. It also explains EKM Metering's system for reading the pulse output water and gas meters remotely with the pulse counting v.4 Omnimeter and EKM Push data system. Finally the video explains the various software options for viewing the pulse data, once the EKM Push system has made it available in the cloud for free.
Water Meters:
www.ekmmetering.com/ekm-meteri...
Gas Meters:
www.ekmmetering.com/ekm-meteri...
Omnimeter Pulse v.4:
www.ekmmetering.com/ekm-omnime...
EKM Push Gateway:
www.ekmmetering.com/ekm-push-c...
Lever Nut:
www.ekmmetering.com/ekm-lever-...
Dielectric Grease:
www.ekmmetering.com/dielectric...
CAT5e Shielded Stranded Cable:
www.ekmmetering.com/4-twisted-...
Customizable Package for Water and/or Gas and/or Electricity Metering:
www.ekmmetering.com/remote-wat...
---------
Encompass.io:
encompass.io/
Encompass Tutorials:
help.ekmmetering.com/support/...
---------
EKM Dash Software:
www.ekmmetering.com/meter-soft...
EKM Dash Tutorials:
help.ekmmetering.com/support/...
---------
EKM Widget:
www.ekmmetering.com/widget
---------
EKM Push Open API Documentation:
documents.ekmmetering.com/api-...
---------
Omnimeter Installation Video:
• How to Install an Omni...
Setting the v.4 Omnimeter LCD Display:
• How to Install an Omni...
---------
Thanks for watching!

[@menardtexsampson3745]

Thanks

[@menardtexsampson3745]

Hi is this a one time purchase set up
Or does it have a monthly bill attached to the set up of the meter. How much does this system cost

[@EKMMeteringInc]

Hi Menard,
Thanks for the inquiry.
It is a one time purchase. EKM does not charge any recurring fees for the system, software or the EKM Push cloud data service.
The cost of the system will depend on what you're needing to meter. We do have pricing available in our online store so you can get an idea of the cost there: www.ekmmetering.com/pages/hardware
Or if you fill out our contact form that should give us a pretty good idea of what you're trying to do and we will be able to give you a quote for the products you would need. Our contact form can be found here: www.ekmmetering.com/pages/contact-us
If you have any other questions please include them when you submit the contact form.
Regards,
Adam

[@wismaranton4525]

what is the pulse width that the inputs can handle, i have one water meter with pulse width of 80ms?

[@EKMMeteringInc]

The Omnimeter Pulse v.4 can handle pulse widths as short as 20ms, so your 80ms pulse should not be a problem at all.

[@stegerauto3105]

Does anyone have some knowledge on reading the units manually. I am using the EKM-PGM75. The reading on the second unit inline is higher then the main unit on the line.

[@EKMMeteringInc]

The black dials on the PGM-075 rad in increments of whole cubic feet. The red dial reads in 1/10 cubic foot increments. Make sure that the meter is not over pressurized (7.25 PSI max). If you have any further questions about your gas meter please do not hesitate to contact our support tram at [e-mail]

[@TradieTrev]

Are these NMI approved for the Aussie market?

[@EKMMeteringInc]

Our water and gas meters have not received NMI approval. We have 3/4" and 1.0" models that have received Type Approval by the California Department of Weights and Measure for revenue grade metering. If you need NMI approved meters, it is possible to use 3rd party pulse output water and/or gas meters with our system for for remote reading. So if you find NMI approved pulse output meters there is a good chance that our remote reading system will work with them.

[@Tri-hua]

Is there a wifi solution without using internet cables?

[@EKMMeteringInc]

Thanks for the question. Our new EKM Push3 gateway, which we are currently offering as beta testing units, can connect via WiFi or ethernet. You can find the Push3 on our website here: www.ekmmetering.com/products/ekm-push3-cloud-data-system

[@AndyHernandez-fp7mu]

I have a question? So I want to monitor only 1 breaker Im will it only read that breaker if I connect it to it?

[@EKMMeteringInc]

Yes you can use our electric meters to meter one circuit instead of the main feed to the panel. When using our Omnimeters, the current transformer(s) would be installed on the branch circuit wire(s) instead of the main feed wire(s). More on meter installations can be found in our online Knowledge Base here: help.ekmmetering.com/support/solutions

[@bkellam]

Why would you stop showing how to wire it part way through? Trying to figure this out is maddening.

[@EKMMeteringInc]

If you have questions about your install please send them to [e-mail]. We have support agents available to answer your questions. We also have an online Knowledge Base, which is a great resource as well: help.ekmmetering.com/support/solutions