Ive seen other mechanics say to never spray directly into the throttle body because the dirt inside will become slush and fall into the engine and make it worst. To spray on a microfiber towel instead
@alex-wr7hg Quite the contrary, it's oily. If it was dirty you'll hear it quick. Most likely the bearing for anything under 20/thousandths of an inch.
Whoops 😂at least I didn’t hurt mine doing it…was a electronic Acura throttle I did have to do a idle relearn afterwards but I expected that cause the throttle body was super dirty
@@recklessdecay7720in electronic throttle bodies there is a little computer on the side of it with some gears. Manually pushing the butterfly open can, in worst case, damage those gears. Usually though, you’ll just have to do a throttle body relearn process if you manually move the butterfly. Disconnecting the negative terminal on the battery can negate the issues tho. If it’s really dirty just remove the throttle body and clean it. Otherwise, spraying cleaner on it and cleaning it on the car will cause all those big deposits to go deep into your car and can cause worse issues
I did it manually off the truck and it did nothing, infact the truck ran amazing after removing the crazy amount of gunk I found. Guess it depends what vehicle
Man that looks brand new it's so clean! Mine was all kinds gunked up. Turn key to on and press pedal to open the butterfly plate is the easiest way I'd say.
the back of mine in my 2012 chevy colorado was so gunked up and dark on the back side i had to remove it completely to truly clean it all off, opened the flap manually gently and it caused 0 issues. after i reinstalled and went for a drive i couldn't believe how much better the truck ran, it was for sure gunked up bad affecting how it ran
NEVER EVER SPRAY THE CLEANER THIS WAY. 😱..YOU RISK DAMAGING THE MOTOR. THE CORRECT WAY IS SPRAY THE CLOTH WITH THE SPRAY CLEANER, AND CLEAN IT WITH THE SOAKED CLOTH, NOT THIS WAY, AND HAVE SOMEONE KEEP THE CAR RUNNING ON PARK, TO KEEP THE THROTER OPEN WHILE YOU WIPED WITH THE CLOTH.
Quick question how do I do this with my 2008 Lexus is250 I got to the throttle body and when when I tried to push on the gas the throttle body didn’t open, any tips?
Click bait.... Throttle body should always be removed for cleaning, then PCM cleared, engine started and allowed to idle for 12 minutes so PCM relearned baseline throttle position. Then vehicle driven for about 10 miles so it can relearn transmission shift points. This is the bad thing about CZcams... Anyone can buy a can of CRC throttle body cleaner, but most cannot do the job correctly.
Incorrect way to do it,especially when the throttle body is facing up. Gravity will pull all the dirt down. Removing the throttle body is required. Cleaning it and then resetting the system.
i think they say to turn ignition key foward first then i think you can move throttle by hand and clean it. double check with someone but i think that is fine to do that way.
Some electronic throttle bodies, mostly Nissan, can throw codes and even go into limp mode if the butterfly is moved without the pedal being pressed. Something about it messes with the throttle position sensor I believe but I'm not 100 percent sure on that
Toyota Master Tech said its perfectly fine, just be gentle. As a matter, he said DO NOT open it using the gas pedal. One can severely hurt themselves as the servo will shut the TB with force.
so key in on position foward and press throttle then spray and wipe.( can i open throttle manually if i cant find a helper?)with key foward in on position.?
cleaned it two weeks ago and forgot to disconnect the battery electrode and I also disconnected the plug and removed the entire throttle to clean it outside after installation it did not work in the correct way delay in pedaling and the pointer went down from 800 I tried all solutions but in the end it was set on its own
Watch detailed video here
czcams.com/video/Bqf6jrmwiyE/video.html
Ive seen other mechanics say to never spray directly into the throttle body because the dirt inside will become slush and fall into the engine and make it worst. To spray on a microfiber towel instead
Has he ever seen engine inside? It's the dirtiest place after exhaust pipe 😅
Indeed you're right and you have to remove it completely
@alex-wr7hg Quite the contrary, it's oily. If it was dirty you'll hear it quick. Most likely the bearing for anything under 20/thousandths of an inch.
Yeah no, that’s not how you do it, spray a rag and then clean, you will mess up your idle and sensors if sprayed directly to the throttle body.
You saved me $230. Thanks. Toyota dealership charging stupid prices
That's awesome
That is how you are supposed to do it you never push the throttle body flap with your hands or it will be damaged. Great video!
Great point! Thanks for watching
Whoops 😂at least I didn’t hurt mine doing it…was a electronic Acura throttle I did have to do a idle relearn afterwards but I expected that cause the throttle body was super dirty
Just curious, why shouldn’t you do it manually. If the car is off isn’t it the same thing as your pedal moving it open.
@@recklessdecay7720in electronic throttle bodies there is a little computer on the side of it with some gears. Manually pushing the butterfly open can, in worst case, damage those gears. Usually though, you’ll just have to do a throttle body relearn process if you manually move the butterfly. Disconnecting the negative terminal on the battery can negate the issues tho. If it’s really dirty just remove the throttle body and clean it. Otherwise, spraying cleaner on it and cleaning it on the car will cause all those big deposits to go deep into your car and can cause worse issues
I did it manually off the truck and it did nothing, infact the truck ran amazing after removing the crazy amount of gunk I found. Guess it depends what vehicle
Always take off your throttle body to clean it 👍
I removed throttle body. What's another four bolts if you got the time and tool.
Man that looks brand new it's so clean! Mine was all kinds gunked up. Turn key to on and press pedal to open the butterfly plate is the easiest way I'd say.
the back of mine in my 2012 chevy colorado was so gunked up and dark on the back side i had to remove it completely to truly clean it all off, opened the flap manually gently and it caused 0 issues. after i reinstalled and went for a drive i couldn't believe how much better the truck ran, it was for sure gunked up bad affecting how it ran
It will take you a while to realize throttle body cleaner is just a fancy brakleen 😂
Yeah Ill just go with what The Car Care Nut says about cleaning the throttle body.
I cleaned one side of my throttle body will i have better throttle respond if I take it off and fully clean it?
Before I start to clean the throttle body do I need to disconnect the negative side on battery?
Yaaa nice job ..spray it right in the engine
Its made for that
NEVER EVER SPRAY THE CLEANER THIS WAY. 😱..YOU RISK DAMAGING THE MOTOR. THE CORRECT WAY IS SPRAY THE CLOTH WITH THE SPRAY CLEANER, AND CLEAN IT WITH THE SOAKED CLOTH, NOT THIS WAY, AND HAVE SOMEONE KEEP THE CAR RUNNING ON PARK, TO KEEP THE THROTER OPEN WHILE YOU WIPED WITH THE CLOTH.
I cleaned mine but took a few mins to remove it entirely wanted to make sure i cleaned it up good without sparying inside my intake manifold
Quick question how do I do this with my 2008 Lexus is250 I got to the throttle body and when when I tried to push on the gas the throttle body didn’t open, any tips?
Same but i have a 2011 is350. Did you manage to figure it out?
Check out the “crc throttle body cleaner instructions video “ nothing wrong in what he has done .
Do you know what houses are connected to the air intake duct? I can't find it anywhere. I'm assuming a crankcase vent hose and a pcv hose.
Clean The Air Filter Box Too, Replace The Air Filter At The Same Time.
Yes, that's howbit is supposed to be
Everything gonna change after it 🤣
Faxxxx bro u know
Did it help 😊
Same method se clean karne par car k RPM phle se kuch jyada increase ho gye h..... Kuch solution ho to bataye....👍🏻
Click bait.... Throttle body should always be removed for cleaning, then PCM cleared, engine started and allowed to idle for 12 minutes so PCM relearned baseline throttle position. Then vehicle driven for about 10 miles so it can relearn transmission shift points. This is the bad thing about CZcams... Anyone can buy a can of CRC throttle body cleaner, but most cannot do the job correctly.
Thing looks clean loll..only a small cleaning with rag needed…yes disconnect battery or you may lose a finger …like this
Thanks..so its ok to clean the electronic throttle body..just throw spray there
Ypu will need to reset your throttle body position sensor otherwise you will be idling at like 2k revs
И грязь с дросселя частично во впуск улетела?
When HE SPRAY DIRECTLY in the THROTTLE BODY Im LIKE 😧😧😧😧
That's how it's designed for, check the using of crc throttle body cleaner
Incorrect way to do it,especially when the throttle body is facing up. Gravity will pull all the dirt down.
Removing the throttle body is required.
Cleaning it and then resetting the system.
But the side that get dirty is the back😭😭 bro clean the front side
How did you manage to leave the flap open? Doesnt it close after you let go of the gas pedal?
here is the detailed video
czcams.com/video/Bqf6jrmwiyE/video.html
👍👍👍👍👍👍👍
Is it not better to remove the throttle body.... spraying that into engine can't be good... none the less the carbon buildup dripping inside aswell
I spray the cleaner onto foam tipped swabs and never directly into the intake.
That's incorrect way , the throttle body should be removed from intake then cleaning from both sides, avoiding the direct to spread inside engine.
But my mechanic didn't do it that way so it causes up and ďown
I opened my throttle by hand and cleaned it, is that okay?
i think they say to turn ignition key foward first then i think you can move throttle by hand and clean it. double check with someone but i think that is fine to do that way.
Some electronic throttle bodies, mostly Nissan, can throw codes and even go into limp mode if the butterfly is moved without the pedal being pressed. Something about it messes with the throttle position sensor I believe but I'm not 100 percent sure on that
Toyota Master Tech said its perfectly fine, just be gentle. As a matter, he said DO NOT open it using the gas pedal. One can severely hurt themselves as the servo will shut the TB with force.
You should take the throttle body off the engine and actually give it a good cleaning
عمل رائع وجميل جدأ
🙏🙏
so key in on position foward and press throttle then spray and wipe.( can i open throttle manually if i cant find a helper?)with key foward in on position.?
You never push the throttle body flap with your hands or it will be damaged. You must get a helper to turn the key on and step on the gas pedal.
@@allimkhan7540 i appreciate that. i cleaned a couple plates but fortunatly didnt push. good info. 🏁
@@allimkhan7540i was slightly pushed that plate, is it ok?
2 nd question please. does battery need to be disconnected? one video said yes but ive never done that. ( thanks for video. very good.)
cleaned it two weeks ago and forgot to disconnect the battery electrode and I also disconnected the plug and removed the entire throttle to clean it outside after installation it did not work in the correct way delay in pedaling and the pointer went down from 800 I tried all solutions but in the end it was set on its own
If you disconnect the battery, you can't open the throttle the way he did in the video
@@fortunatedad7695 i appreciate reply. 🏁
You're supposed to take it off to clean it
I'm just should how this cleaner can be used, everyone don't have enough tools and on some cars, the whole intake has to be removed
I did this and my check engine light came on 😢
Check all the clam and the other items that you have worked and let me know.
Never do this on a honda.
Why? I did on mine except I spray the cleaner onto foam tipped swabs.