amazing video as always! good inspiration for a c36 AMG m104 3.6L turbo project. AMG has already installed AMG cams, piston and rods. ready to go for a turbo install. waiting for your kit 😊
To remove carbon deposits on pistons I use Simple Green household cleaner. I’m not sure if they sell that in Germany. Here in the US you can buy it everywhere. It has no strong smell to it and works amazing. I just soaked a set of pistons over night that came out of a Mini N12 engine that burned tons of oil. I just used a toothbrush to scrub them and they look like new.
What is the reson your not using the oem pistons IT is already tested the the Will easy hold 200hp per cylinder. I understand You need lower compression but why not use shorter Rods . The are also wide range used. ?
I have watched your assbliing videos several times))) your explanation is super. I will a question if you don't mind. Which valve valve guide manufacturer would you recommend for 606 head rebuild?
My preference is to use the rod drilling for oiling and not squirters from the block .. this way all the bearings are given priority before piston cooling by oil. Hey buddy do you have the part number for those head bolts? this Video is 2 years old now how did it go ?
Great video , I’m doing a turbo project for my C230K have you any advice? I’m thinking MLS head gasket and forged rods looking to get 300bhp maybe 350bhp
Hello! Thanks for your video! I can't find pistons m104 90.15mm . And I will use pistons from ford expedition 90.20mm it cipher. But it flat without holes for valves. Is it possible or no? what are you thinking? Thank you so much!
Hey there. I have a 1996 c280 sportline. I was wondering if you know if it is possible to run it coil on plug by adding 3 extra standard coils and eliminating the 3 leads. Any info on the ignition system would be much appreciated.. Thanks : )
HI THERE I WOULD LIKE TO FIND OUT W203 MERCEDES MANUAL GEARBOX 6SPEED WHEN FITTING IT TO A OM605 MERCEDES DIESEL ENGINE. IF I CAN USE THE ORIGINAL FLYWHEEL OF THE W203 I WOULD LIKE TO EAR FROM YOU . REGARDS ANTONIO.
You have to try Paint thinner to remove the carbon deposit. This works most of the Times pretty good
Endlich jetzt wird es interessanter
amazing video as always! good inspiration for a c36 AMG m104 3.6L turbo project. AMG has already installed AMG cams, piston and rods. ready to go for a turbo install. waiting for your kit 😊
Stock headgasket, stock pistons, stock rods is good for 800hp on e85, in sweden there is allot of dristers with m104 700++hp
Very valuable information , keep it up with posting the videos 👌🏻
To remove carbon deposits on pistons I use Simple Green household cleaner. I’m not sure if they sell that in Germany. Here in the US you can buy it everywhere. It has no strong smell to it and works amazing. I just soaked a set of pistons over night that came out of a Mini N12 engine that burned tons of oil. I just used a toothbrush to scrub them and they look like new.
Erste paar sekunden gehört. Okay deutscher boy am schaffen😂👍🏼
Super Video auf deutsch wäre nicht schlecht
🥰
hello, I wanted to ask what connecting rods were installed and where they were purchased, I'm looking for 144 mm as amg
What is the reson your not using the oem pistons IT is already tested the the Will easy hold 200hp per cylinder. I understand You need lower compression but why not use shorter Rods . The are also wide range used. ?
I have watched your assbliing videos several times))) your explanation is super. I will a question if you don't mind.
Which valve valve guide manufacturer would you recommend for 606 head rebuild?
Try oven cleaner for carbon material.
My preference is to use the rod drilling for oiling and not squirters from the block .. this way all the bearings are given priority before piston cooling by oil. Hey buddy do you have the part number for those head bolts? this Video is 2 years old now how did it go ?
Use heated DMSO for cleaning carbon deposits.check on CZcams.
Hello have 103 Engine.Wonder can The 104 4 valve head pas The 103 block!? May son and me building Turbo And MaxxEcu Efi...
Hi, what manufacture for rods & mm length please?
Hi. Which inner valve spring did u use?
Great video , I’m doing a turbo project for my C230K have you any advice?
I’m thinking MLS head gasket and forged rods looking to get 300bhp maybe 350bhp
Do you know about what engine management system you will use on the M104?,HFM, ME2,or aftermarket and what turbo will you start with?
so Toto Wolff is now building M104 engines ....
Hello! Thanks for your video! I can't find pistons m104 90.15mm . And I will use pistons from ford expedition 90.20mm it cipher. But it flat without holes for valves. Is it possible or no? what are you thinking? Thank you so much!
Hey there. I have a 1996 c280 sportline. I was wondering if you know if it is possible to run it coil on plug by adding 3 extra standard coils and eliminating the 3 leads. Any info on the ignition system would be much appreciated.. Thanks : )
dieser geile deutscher akzent
HI THERE I WOULD LIKE TO FIND OUT W203 MERCEDES MANUAL GEARBOX 6SPEED WHEN FITTING IT TO A OM605 MERCEDES DIESEL ENGINE. IF I CAN USE THE ORIGINAL FLYWHEEL OF THE W203 I WOULD LIKE TO EAR FROM YOU .
REGARDS ANTONIO.
Hello, do you know who can help remap/tune m104 turbo on meqasquirt?
How much boost it can handle with stock rods?
Is it possible to make the noise of the m104 engine the same as the rb20det engine?
They actually sound very similar
Mein m111 hat andere Kolben ist auch Kompressor Modell aber die erste Generation die hat eine Vertiefung ist nicht so glatt wie der eine bei dir
Du redest wahrscheinlich vom 230er. Da liegt es an der größeren Bohrungen dass die Kolben vertieft sind. Gruß
@@CZSMotorsport genau 230 Kompressor stimmt die sind größer hab nachgeschaut
What are those rods?
I-beam design?
Yes, check link in description
How do your videos dont have 200k plus views ?
Because they lack quality and entertainment 😆
I watched the m104 vids all over again and i dont even own one 😂
What rods are you using?
You can find them in the online shop of www.stern-garage.com