Taking an Arctic Cat Diamond Drive Apart
Vložit
- čas přidán 5. 01. 2014
- Hey CZcamsrs....
Check these guys out product works real good I add it to every tank of fuel!
Promo Code Gives you 15% off
Promo Code: KCYukon1
www.fuelox.com
I have tested this out and my results were impressive, no more 20 products to add to your fuel... One product covers 5 different things. 1.) removes water 2.) Improves Power and fuel economy 3.) Stabilizes fuel 4.) Reduces Emissions 5.) Lubricates Engine components
Works in all engines 2 stroke, 4 stroke and Gas or Diesel engines
Stuff I use to make videos
Action Camera's that I use as of 2020!
Garmin Virb + Mic Technology
amzn.to/3eO4Ls1
Rylo 360
amzn.to/3eQoR54
Lexin Mic Hookup
amzn.to/3cQETdw
Want to chat email me @ kc@kcyukon.com Cheers!
Diamond Drive Change Oil • Change Oil on Arctic C...
Diamond Drive Apart • Taking an Arctic Cat D...
Diamond Drive back together • Putting an Arctic Cat ...
Diamond Drive Explodes • Arctic Cat Diamond dri...
Diaomnd Drive with Reverse Part 1 • Diamond Drive with Rev...
Diamond Drive Reverse Part 3 • Diamond Drive with Rev...
Diamond Drive Bearing Change • Change Diamond Drive B...
Taking an Arctic Cat Diamond Drive Apart
Brought to you by Irwintech search it! Like it and subscribe thanks! - Auta a dopravní prostředky
Nice looking at the light bulb on the floor ha ha
Yea I know lol :)
awesome video, very informative. Just a tip: when you're filming a video like this with a GoPro mounted on your chest, GoPro's don't show objects in shadows or darkness as well as a digital camera, so when you show, for example, the planetary gears inside the diamond drive and how they go in, if you set up a trouble light or flashlight to illuminate it while you're doing it, makes it a lot easier to see on video.
Tip#2: the thin steel "C-shaped" clips that are used to seperate the parts: they're called "circlips".
Another tip: if you're having trouble getting the outer race of the bearing out, heat the edge up with a small propane torch, it'll pop right out. Vice versa, when installing the new bearings: Put the new bearing in the freezer for 10 minutes, heat the edges of the gear case where the bearing is going into with a propane torch, when it's nice and hot, quickly pull the bearing out of the freezer and it will slide right into the hole with minimal effort (steel expands when heated, and contracts when cooled).
Cheers mate, keep up the videos, very helpful for a guy like me! You've saved me a lot of money!
awesome happy to hear it helped out, I have always just done this as a hobby to help others I'm not in this for the money like some of the professional you tubers. My equipment is not very high-quality so the videos are what they are. Anyways I'll pin your comments as there is some good advise you posted Thanks!
hey also thank you for comments as well this helps me build better video's for the future!
would have been great if camera was on the project most off the time
It is what it is this is a hobby for me....
nice vid keep it up
Joe Helland thanks!
Thanks for the info brother I got a feeling I'm paranoid about taking apart my 2006 SaberCat to replace the track lmfao.. I will proceed with caution 😉
Glad I could help
What are you using to set your sled on its side without messing up the plastics?
+Chris Haddox Hey Chris in a pinch I have an old snowmobile track that I use.
Did you just use a vise to press the bearings on? Thanks
That bearing should slide off and on with little work. I would use something like a socket and place it on the inner circle of the bearing and then tap it on with a hammer. Inner circle of the bearing must be used for contact. hope that helps cheers.
Thanks for the reply
How do I get the ring gear seal off the dd case?
Do you still need help?
@@KcYukon I figured it out. Thank you though
Nice job filming the floor
I tried
Well, its a cat
Yes it is!!! thanks for watching!
All i can see is the floor
ya back in the days when I wasn't very good at this... .oh wait im still not very good at this this youtube garabage I mean ;)
That diamond drive is junk dude. Time for BDX lite.
I would be interested in checking it out do you recommend them have you been using a box lite for long?