How To Install Lockwood 001 Lock To Apartment 10min
Vložit
- čas přidán 5. 09. 2024
- Quick video on how to install the Lockwood 001 deadlock on a unit front door with a metal frame. How to install a Lockwood 001 in under 10 min. Fire rated lock, insurance approved, Unit deadlock, Installed. To buy this lock see our lock shop .
#Locksmith #LockShop #Locksmithparramatta
www.drlock.com...
www.drlock.com...
www.drlock.com...
Younger brother installed lock 5 years ago & didn’t do a good job. Returned from overseas (ex pat) 5 years later & watched your video. Now have to find the key ha ha!! Cheers mate from NZ.
Amazing video! Much better than the instructions that came with the lock.
Big thanks!
after a couple of hours trying and going a bit nuts watched this little gem and done in 10. thx made my life that bit easier ;)
Thanks mate! I removed mine from my apartment to upgrade (or so I thought) with a Samsung digital lock, found out after the fire inspection that it’s not compliant so had to go back to the good old Lockwood 001! You video made my install back easy!!
Now I see why you suggest a local locksmith to install this lock thanks for showing us your own tricks neat.
Dr Lock. You are a super star. I couldn't get my key out of the lock while reinstalling the whole assembly. The "turn the key 180 degrees" after putting on the hub was an "unknowable" to me. Indebted.
Nice work! It's nice to see someone take so much pride in their work.
Dr Lock, I couldn't figure out one element of the putting the key in and turning 180. This video helped me fix it! Thanks!
That was a great job. Professionals do things properly. Amateurs like me do just the bare minimum in order to get to “put the tools away” time.
I didn't know Russell Crowe was a locksmith
Excellent tip on using the self tapping screws in place of a more expensive drill bit.
Learn something new everyday.
Thanks for sharing
great instructional video, the only mistakes I made were my own fault for not paying attention to the video 8:05 once you have checked it turns freely ensure that the v part of the wheel is facing in where the strike plate will be and then proceed to install the latch body. The key wont be inside the lock during latch body installation if you've done it correctly
appreciate this mate. prev install only used 1 screw for the inner plate so the barrel was getting loose. had to take it apart to get to the 1 screw tighten it up.
Beautiful lock. I wish they had more of these in the states... Thanks for sharing.
Thanks a lot. I was able to replace my old lock due to your videos. 👍👌🏅
Thanks for posting this...saved our bacon today as we had to install this lock on our front door! Cheers👌
Hi thanks for the video, took it off to paint the door, reassembled using your video, thanks from Adelaide
Thank you! Was stuck at one point and couldn't work out where I went wrong, it was the 180 with the key that I was missing
Excellent so nice guidance line
Dude you are great man
Hopefully see more new clips
Joo
London Uk 🇬🇧
Great vid, thanks 😊
You know when you use one hand to open the lock and it gets held in place, "hold back" on our lock this has become a hair trigger and lets go easily, is this a simple fix? Or is the lock worn out?
Lovely work! Pity you are not in Melbourne. As a rough guide what would it cost to supply and fit a Lockwood 001 on a timber door. Actually replacing an old Yale nightlatch. Backset is same at 60mm.
Thanks mate
Nice. Dang quick too. Are those screws in the jam really going to hold up to a swift kick? They look pretty short.
They are made to be forced off when the fire fighters use the big crowbar tool, I have tried kicking the door , not so easy, but not impossible
I’ve gone to plenty of break ins and I usually find the door is split in half or the jamb has split.
Ive seen breaking when they have cut the door inhalf basicaly pointless even having a lock. If they really want too get in they will.
Thanks so much for this video, I picked up at least 3 new tips from this. Much appreciated 👏👏👏
Great video, very useful.
Thank you, you’re a life saver !!!
No problem!
Nice video and explanation with easy instructions. How to make the nob not to stuck which hold the lock unlocked position?
excellent video - thanks
Very nice, cheers!
What is the rush for dude. If feels like you showing off how quickly you can get it done rather than how patient you cN explain. Thanks btw
I need to replace an old one but I can't get the old one off the door, the external part has no visible screws
Dr Lock! Great vid. I don't know what's going on with my 001, but all seems to be working as per your vid, until the door is actually shut. The key won't turn from the outside. I think it's got something to do with the secondary, but not really sure. Distance is about 4-5mm from strike plate when closed. If I hold secondary all the way in though when door is open, key wont turn at all. We normally only use from inside to open and hold back, but obviously annoying when door blows shut and lock ourselves out in back yard >_
Sounds like the back of the lock is not all the way back, it needs to be put on. pushed back, then the 2 screws, if the lock is not all the way back from the front the key will not turn all the way
@thousand Years Of Oppression
Had the same problem with my lock.
I compared it to another 001 and the problem is with the manufacturing of the backing plate. Take lock off door and screw it all together and try to unlock with a screwdriver. The problem will still persist. Now back off the side screws and install two small spacers between backing plate and the lock body. Tighten up side screws. The problem will go away.
Take it back and get a new backing plate, or do as I did (poor mans way) and bend the lugs to make up for spacer. You need a strong vice and a coal chisel. It’s a crap fix but it does work
Have you ever tried fitting the strike first? I find it a quicker and cleaner fit
I have this one on my door but I can’t get it off. Any tips?
Hi Dr.! Which bolt cutters are you using to cut off the tailpiece? I bought a Kingcrome one (Bunnings) but I'm really not happy with it.
How much would you charge for doing that job
Great video!!
Hi my key from inside is not working its stuck at at one point ,opening closing fine but not locking from inside please advise
the lock is not set to the same key as the outside
Hey mate. We live in an apartment and have this model. For some reason the deadbolt doesn't retract sometimes. Does it just need some grease?
nice work.
hey man that was cool good stuff
Great Video super informative. Could this be keyed alike to say, Yale deadlocks?
not to a yale different key shape
Not sure if you can help me. I replaced a whitco deadlatch attached to my external steel door using instructions supplied & your video which I watched multiple times. My issue is the door doesn't stay closed, I can close it & then just push it open with my hand. I have no idea what I did wrong.
you need to adjust your strike most likely up or down, the latch is not going into the strike
Question. Does that meet fire regulations and is it possible to change an existing deadbolt to a self closing latch?
The 001 dose, you will need a 001 sleeve to change a deadbolt to a self latching lockwood 001 , but they are currently sold out
Awesome tips my friend. I've got a question. As a new locksmith in the US what key cutting machine would you recommend me buying? As always bud keep up the awesome work.
Hi, hat is your budget and what do you need the machine to do ?
@@DrLockShop 2500 is my budget and I need one to cut auto and residentials like kw, SC, and a few other. I need to save as much as I can so I can buy other tools as well like lock out tools for auto
Tennessee Lock Picking This might work for you. www.clksupplies.com/collections/semi-automatic-key-machine/products/the-hpc-power-speedex-key-machine
czcams.com/video/J6VLkkmU4dw/video.html
Why we need to cut that thing you show us on the video can u please explain
it connects the front cylinder to the back part of the lock, its made to be cut to size of the door, if left long it wont work
Dr Lock thank you for your reply i ll try to fix this problem tomorrow today i wAste my time but after watching your video seems like i can do it by myself
When you state that the lock won't comply if installed too high. What do you mean by that? Fire rated compliance?
No council, it will still work in a fire, but the hight is part of the fire door regulations, needs to be accessible for short people too, in short , if you mount the lock high to keep the kids in, you may get asked to lower it when they do a fire inspection
@@DrLockShop Thanks. Is there a set height limit stated?
Also with the 3mm packing, how much out would the door have to be with the frame to use a packing?
Can that same unit be installed on right side inwards opening?
yes right or left ... www.drlock.com.au/store/lock-shop-locks-domestic-commercial-locks-deadlatches-nightlatches-deadlatches-lockwood-001-deadlatch-0013k1sc?search=0013&page=2
@@DrLockShop thanks! Only thing is my key holes are upside down 😆 maybe I can spin cylinder around but not then lever?
Oneday people want to change digital lock swap handle lock , 001 lock will trouble to Put on, because it’s too close...
Not advisable For Main Door.. This is Hard To Open From Out side if Your Key Forgot Inside... If you Need Go Inside You Force To Open It destroy The Lock..
any good locksmith will just pick the lock without damage
Assume video