stihl ms200t 020t chainsaw look inside throttle linkages and switch also show why would not turn off
Vložit
- čas přidán 27. 04. 2013
- Stihl 020t / ms200t Quick look inside top handle throttle & choke linkage / on off switch area without bits falling out.
Show why saw may not be turning off at switch.
(This saw is an ms200t i called it 020 in video)
See my other vid on MS200t Brake band replacement /clutch cover strip down.
Like so many other people in the comments section, Id already made that first mistake. Found your clip when I was in damage control mode!! Thank you so much for such a clear and concise clip. Everything explained clearly enough for even a numpty like me to follow. The fact that you are still helping people on the other side of the world 9 years after posting is something you should be rightly proud of mate. Thanks once again.
Awesome video. Thanks....I knew i was in trouble at the beginning when you said, "dont do that...it all fell apart" (I was already there)...watched this and put it all back together. Runs great
My God . . . I did exactly what you did wrong, and of course all the linkages and springs fell right off to the work table. Three hours lost last night, and four more this morning with tweezers and tape trying to finagle the parts back in place. Almost in tears and then I found your video. You are an absolute God send. You have just reserved your seat in heaven my friend. Great Work!!
I know this is an older video, but it’s still helping tears later!
Thanks for posting. Essential viewing for MS200T owners.
Thank you for this good clear video. I didnt have the patience to find out the logic to put the parts together again... Saved me a lot of effort since i live in mid-France and there are not many stihl dealers with knowledge overhere! Thanks again!!!
This video saved my Chainsaw!
Thank's a million G1DDD for taking the time, and having the generosity of spirit
to make this video.
Many CZcamsrs have benefited from it over the journey, and more will benefit in
the future - there are lots of MS200t still (no pun intended) around!
You're a great man G1DDD - God Bless!
you just saved my butt. I took the handle apart to fix a sticky throttle, didn't take the kill switch off first and all the parts went BOING. Then came searching for a vid like this Thanks for the close up of the assembly so i could put it back together and for making this video. Too bad i didn't watch this first and hear your advice at the beginning...
my boyfriend managed to close it after multiple attempts, thanks to your video. The pieces had flown away. The problem was with the white switch. Thanks 🙏🏻
Legend, thanks mate, I think the spring on my cut off switch is buggered. Wont switch off but the spring won't stay in place. You should charge everyone 10 bob for watching this video as you have save me and everyone good money. In typical English fashion you are clear and concise in your instructions. Fantastic
SO FANTASTIC!! I did exactly the same mistake. Pulled the handle apart, and all the stuff fell apart. With this video i got it all together in 10 minutes. THANKS!!! Next time all check youtube BEFORE i take my saws apart. 🙏
Thank god you posted this. Made the same mistake and had pieces everywhere.
Thanks man! Many karma points for that one- a life saver!
Dyango
Cheers mate. I just pulled mine apart without removing the switch. Had it back together in no time after watching this video.
Can't thank you enough for taking the time to make this video. Like you said, only took a few minutes to get sorted.
Brilliant 👍👍👍
Man this video is gold, literally the most helpful video I have ever watched on CZcams. Very well done thank you
Bloody legend mate!!! Helped me out heaps.
Thanks from the Ferals
Thank you, I didn’t see the video until after I made the mess. I was able to fix the shorted stop switch and reassemble my chain saw because of this video. 👍👍👍
Thank you soooooooo mmmmuuuch my dear friend for making this video!!!! You saved me hours and hours to figure out how to reassemble this boody handle! Thank you!!!!!!!
Thanks for posting vid.What a fiddly job to do.Wouldve been lost without your help!
Thanks man! Easier than I thought! Time to go make some money!!
Thanks very much! All back together with a working on & off switch. I also did exactly what you said not to at the beginning 🤦♂️
Brilliant video i had the same trouble taking mine apart for the first time very helpfull thank you
Thanks for posting. Wished id watched first. Just spent 30 mins looking for the bits that sprang out in a pile of sawdust !! I had a broken stop switch wire. Grrrrrr
Thanks for the video. I did the exact same thing today and this video got me out of the s**t lol. Top man cheers
Thanks for this, good to see someone who takes care to give good clear information. I did one of these about 10 years ago, but you forget don't you?. Cheers
Cheers Andy, appreciate comment.
Just to say thanks for the vid it helped me out of a spot!
So good. Thank you. Saved me hours.
Thank you very, very much, have the same saw, whick leaks oil, but with your video I come a big step forward!!!!
You just saved me so much time! Thank you!!!!
top video, you helped me a lot.greetings from Germany, keep it up
Thank you very much for the video, it really helped me.
Keep up the good work
Thanks for your video really helped me out today.
Thank you so much for making this video.
Great video! Thanks for the help!
Perfect video...! Thanks a lot! Today i have repair my saw with your remarks.
It‘s really the best manual about the on-off-switch - also for german person! Greats from germany!
Awesome mate did exactly the same as you. Was about to smash it to bits haha. Lifesaver thanks again.
Fantastic mate. Cheers
Cheers dude I would of been screwed without this video!!!!!!!!
This video saved me big time thank you so much
Fantastic video, well done!
Thank you so much for this really helpful
Brilliant, 🖒🖒🖒
You saved me man. Thank you!
Great video. You saved ne from just given up and throwing it away. 😆
Top man, wish I’d watched this before taking it apart though 🙈. Meant I could put it back together though 👍
Thankyou! Lifesaver!
Mil gracias Hombre .1000 Thanks man!
So the way I shut my saw off is turn the switch back to the choke position. I guess the same wire is bad you say yours was broken. Thanks again
Thank You So Much For You video God bless You
Brilliant ! so helpful
thank you very much did same thing you did
thanks for this mate
Great video thank you
rop zeer bedank voor uw video ga door
Thankyou for positive comment, appreciated.
Cheers Glad video helped, thats great.
Wish I watch this before I started and I had the same problem 😂
Thats great, im pleased mate. Cheers.
Thanks for video
Great vid m8
Very handy,Thanks!
Just saved me paying someone to put my saw back together when I took the handle apart!
Thanks brilliant bud! love it
Many thanks, saved my arse 👍
Superb!
Mate you just saved my ass with this video. I feel like we both deserve a pat on the back for getting that shit back together haha
😂😂😂👍
Absolute legend
Life saver!!
Awesome…….thank u….
Thanks!!!
Thanks❤
How do you go about fixing the saw if the selector switch is moving into full choke independent of depressing the throttle and springing from full choke to run (independent of pulling the throttle)?
THANKYOU!!!!!
wish I could give this video 10000 likes you just saved my ass brother lol thank u
You can tell you're a ham. Very helpful, just bought one of these sounds like it may have carb, fuel, exhaust issue box down after running 20 secs. Any ideas which stihl saws share the same parts.? I have an 021, 023 and 029 so if I need parts I might buy more than one. And probably use cheap Chinese copies depending on the part. Anyway thx
and thanks again!
Thanks for the great MS200T information. Could you show how to remove the MS200T flywheel.
Thankyou, glad to help. As for clutch removal here is a great video already uploaded : Stihl MS200 Chainsaw Sprocket & Clutch Removal, Inspection & Refit its by guy called inciderinfo Cheers
Dzięki przydało misię to
Show how put kill springs in
So funny because it's what I did too. Thought if I could do a 192 it couldn't be harder
Thank you so much I got stuck on the bottom connection spring. Very informative, and had a good laugh
I love you
He don't show how the two spring leads fit in at the front , the right or top most one is kinda obvious.
The lower one is not, he shows where it contacts the choke on off switch but absent is how it lays in the handle.
Invest in some good handle Torx wrenches.
Took me ages first time also
Orange wire to orange plastic white wire to white plastic. It's color coded for a reason
Ditto
Ya know 020 is a nickname because 020 is an earlyer saw there was never an 020t ?
Thanks!
glad to help