Cruze M32 Transmission Fix!!! (Bearing Replacement for Getrag M32 6 Speed)
Vložit
- čas přidán 5. 12. 2020
- Today we tear apart the Getrag M32 six speed transmission in my 2012 Chevrolet Cruze Eco to find bad bearings causing my shifting issues and noises. All bearings get replaced with Timken upgraded bearings for a smooth shift and quiet running noise. Be sure to subscribe for more unreal content!!
good budy! i´m Portuguese and i´m rebuilding my OPEL ASTRA M32 GEAR BOX
Thanks for sharing this video.
Thanks for the vid! I wasn't sure if the bolt in the input shaft was reverse thread but you had a nice clear close up of it! (Right hand if anyone missed it)
to unscrew turn left the screw from the Primary shaft
Excellent job and great video, I certainly appreciated it.
Great video. Huge value here for me. I'm going to attempt this for my Vauxhall. Thanks very much for sharing this information❤
we have them in a wide selection of cars in the uk , i have one i need to rebuild. great lil video, dreaded chocolate bearings!
Very well done mate, nice work!
Thank you for sharing this information. Nice work
Insane man.
Did you think about rebuilding with metal bearing cage instead of plastic? Was there pitting on the rollers themselves? I believe once those plastic cages wear and there is slop in the bearing rollers and that's the source of this issue. That's why I always go with metal cages because they last.
I'm about to do this in my Getrag trans on my fusion, I'm going to measure the bearings OD, ID and width to size the bearing and then I'll order whatever flavor bearing I want that is compatible. Thanks for the video, definitely giving me insight into my future project!
I have a m32 aswell in my 1.9cdti 150 and i saw a video from uk i believe and they have upgraded the "pan" of the gearbox so the 5/6 can be more lubrificated and they also got bigger and better bearings. But i couldnt find a way to buy it to mount on my gear box
Hello Sr., I will appreciate if you can mention me when is necessary replace gear bearings, now I'm replacing all shaft bearings (easy to find new ones in Chile, three of them in bad conditions) but I'm not sure to disassemble input and counter shaft to replace gear bearings (not easy to find), symptoms: a lot of smashed metal in drain and filling magnet plugs and noisy manual transmission, many thanks!!
Very difficult to put out this shims . Any tool to buy for them? Have the same bearing tool to remove bearings. What kind of bolt was that?
Sixth gear bearing is the most common to go with the m32.
Can you share the parts list you used including part numbers? This is a fantastic video as I do foresee this coming for me in the very near future.
I would like that as well!
How long did you have the bearing problem before you rebuilt it? Mine has the output shaft problem now it seems....
Does the apply to the 6spd in the sonic rs? Do you have a list of tools that you used for this rebuild
I have some crunching when shifting and the gear noise from 20mph and up and want to do this rebuild.
What size was the input shaft bearings
hi, where did you buy your bearing cage extractor? Thx
Did you reuse All the shims/discs or put in New ones?
you need to reshim the axles when you put new bearings in
Thanks for the video! I have a corsa D Vxr as well and I have to change a synchro but I've been told by GM that not every m32 firt to second synchro can fit in my m32 gearbox because these gearboxes were put in other cars as well, so I can't find a way to make sure I buy the proper one 😰
Unfortunately it sounds like you need to take a chance and buy one and hope it fits. Not sure how else you’d figure it out
Take it apart and measure the synchro. You should be able to order based on dimensions. Someone has to know what you need if you have the dimensions, otherwise take it to a machine shop and see if they can fabricate for you.
I made the transmission parts for the Saturn SL and Ion
Have you had any issues since redoing the gearbox? Apparently the shims need doing when you rebuild it or the gearbox won't last as long?
I haven’t had any issues at all. from what I can tell the shims are to set the backlash on the ring gear, in which case they don’t need replacing as long as they go back in the exact spot they came from
@@bradenrein thats a massive weight off of my mind! I have literally just started to get my box sorted to day and the shimming is the part I'm worried about as I can't find any info on them regarding setting. Do you know if I can reuse the original shimms with uprated bearings for the gen 1 casing?
You can if you are just changing bearings and keeping both sides of the case like I did. If you upgrade the casing you need different bearings and new shims.
Do you have a link to where to buy the bearings? I have a 2012 Cruze eco also.... mine jumps out of 2nd gear when accelerating. I think I need syncro and 2nd gear do you know where to get these?
Vauxhall M32 Gearbox Shaft Bearing Rebuild Kit - TIMKEN was the bearing kit I purchased from www.bearings-online.co.uk
How do you get the shift tower in
Lots of wiggling to get it to align properly
Oh. s.r doutor, então e a referencia dos rolamentos? O mais importante ficou por mostrar, mais uma pessoa normal.
Круто. Молодец.
Cruze in US, Astra in Europe. Misfortune companions.
Hi, can i ask you do i have the same problem? czcams.com/video/l-lr9uVdGtc/video.html I have it moving on third and fouth gear.
If you’re having any movement of the shifter, it likely means one or more bearings are shot. It just might be a different bearing than the one I had shot