Immer wieder imponierend, vor allem wenn man die Umstände bedenkt unter denen geplant und produziert wird!👍👌 In den Industrieländern unbezahlbar, 100% Kopf und Handarbeit!
Yeah, I love the paint preparation. I wonder how long the paint will actually stick to the surface. I’m sure it looks pretty for a day a week maybe a month but I’d like to see it after a year. It’s all flaking off.
What would be awesome is seeing those guys produce parts or upgrades for thier shop. Making it from what we see now a normal decent shop with protections but made by them. That would be cool.
اللهم صل على محمد وعلى آل محمد كما صليت على إبراهيم وعلى آل إبراهيم في العالمين إنك حميد مجيد اللهم بارك على محمد وعلى آل محمد كما باركت على إبراهيم وعلى آل إبراهيم في العالمين إنك حميد مجيد.
The team of designers of the chief engineer who designed this gearbox is not qualified and failed: 1. Observe the overall structure of the gearbox and the construction conditions; With its existing construction tools, there is no reason to divide the work piece into three parts, and two joint surfaces are used; A reasonable partition only requires two parts and uses a single bonding surface. 2. Appropriate bonding surfaces, which can be: a. The common plane that exists in the extension line of the three gear shafts. b. The plane perpendicular to the center of the gear shaft extension line. 3. If there are no other special needs, my personally thinks that b. It is more reasonable, as long as there is no error in the measurement, the bearings at both ends of the three shafts, combined with the simultaneous construction, the shaft hole will be more accurate, and other bolt holes also save a lot of measurement work. Personally, I don't think that b. there are any difficulties in assembly.
Up until now, the biggest scraper on CZcams belonged to Fireball Tools. Also, check out that lazy ol' fart with the sunglasses, just sitting on his lawn chair. That's GOT to be the chief engineer.
For the sake of Allah, get some proper wrenches and maybe a pair of steel tip boots or something to cover your toes maybe I a pair of gloves too and I know how about some safety glasses you guys sure like living on the edge but you’re good at polluting that’s for sure
Just what was that cluster-fxxk at the start? Wasn't annealing, wasn't hardening, wasn't straightening...any thoughts? Haven't they heard of heat/dried CO2 for inserting shafts? Dropping that heavy weight and hoping? What's that all about? Can't they buy 350WT grade steel? Entertaining to watch BUT seriously, what are the workplace safety stats? Do they even compile them?
Not good practice to bore frame for bearings with clean faces then final assembly adding thick gaskets. Gearbox won't last long. Interesting method of assembly of shafts and gears also bearings onto shafts.😢
If the safety Nazis moved in on this factory, no more production, no more employment, no more company. They would become uncompetitive and the end would be disastrous for the local economy. Don’t try to impose western standards on this scenario. 😡
Everyone is talking about safety shoes but you people must use your brain little bit what is the temperature of workshop how you can wear steel toe shoes there?
Bueno no se qué pais es creo que alguien deberia darles. Alguna nocion al menos en seguridad . Por lo demas alguno debería aprender la genialidad del no tener lo que tenemos los demas
Are you kidding me why even by the paining I must be the company color I’ve seen everything now that’s a fabulous piece of machinery there fellas nice Hackett whack it
Set of idiots are on the job having so big work shop, they should have incorporated one hydraulic press to meet their range. Job could have been still easier & neat.
For the sake of Allah, get some proper wrenches and maybe a pair of steel tip boots or something to cover your toes maybe I a pair of gloves too and I know how about some safety glasses you guys sure like living on the edge but you’re good at polluting that’s for sure
Hello my friends, I am the inspector from OSHIT. Looks fine, carry on!
Love from India you are doing the great. One day I will visit all of you.
You guys are crazy. A hard hat or safety shoes would be useless, but you produce some awesome things.
I look forward to seeing more of your content.
Dangerous work. So You might get to see the Work, without a few of the Guys.
Immer wieder imponierend, vor allem wenn man die Umstände bedenkt unter denen geplant und produziert wird!👍👌
In den Industrieländern unbezahlbar, 100% Kopf und Handarbeit!
MashaALLAH
Watched full video .... incredible Professionalism and workmanship
#Pakistan_Zindbad
Great video. You guys are really good.
I ran a planner in the US in papermills. Loved the flat work. Broadnose for a great finish
Now THAT'S cooperation as these brilliant men work.
These ppl use what they’ve got…talented guys with those worn out machinery….
Just plain experience that gets the job done. Fantastic.
To think I used to machine gearboxes the size of a small house in the 1970’s to a 0.001” that ended up in sugar cane mills, this makes me weep .
What a job! That gear box is huge!!! Is it going in a ship? I'm glad it's them and not me. Good job though.
Pakistanis hardworking people
But brain less
Yeah, I love the paint preparation. I wonder how long the paint will actually stick to the surface. I’m sure it looks pretty for a day a week maybe a month but I’d like to see it after a year. It’s all flaking off.
What is this gearbox for? You should have explained this, or accompanied it with a video of how and for what purpose it is used إبراهيم من هولندا
Probably for heavy duty sheet bending, to build tanks
What would be awesome is seeing those guys produce parts or upgrades for thier shop. Making it from what we see now a normal decent shop with protections but made by them. That would be cool.
Clean tidy work area and all the proper safety equipment
and that it is hard to see clean gearbox inside before assemble
Wonderful hard working people.
Amazing!
As an engineer this truly makes me sick. This is manufacturing technology of the 1800’s. Warranty to the frontdoor.
I'm sure all the dust, grit, and metal shavings are there to aid in wear in processes, lol
Va até lá retirar vrsrs, moderninho...rsrs@@donburrito2485
Actually, it is manufacturing technology from the 1940's.
It works for such poor economy. That's enough.
Blah blah blah blah blah
Эти ребята в ночнушках меня восхищаются.
100% Nightmare fuel for OHSA folks
Covering dirty rust with paint, working with bearings on a dirt floor - definitely in need of quality control.
Excellent work❤💐👍👌
this shop needs a BIG
Jak można pracować mając taki totalny gnój wokół? I to prostowanie płyty na podłożu z piasku. Średniowiecze w XXI wieku.
設計這個齒輪箱的總工程師的設計師團隊不及格:
1. 觀察齒輪箱的總體結構,以及施工工況;以其現有施工機具,毫無理由將工件分割為三個部分,並且使用了兩個結合面;合理的分割僅需分割為兩個部分,且使用一個結合面即可。
2. 適當的結合面,可為:a. 三齒輪軸心延伸線所存在的共同平面。b. 垂直於齒輪軸延伸線所存在中心的平面。
3. 如果沒有其他特殊需求,個人認為b. 較更為合理,只要測量不出現誤差,三軸兩端軸承處,合併同時施工,軸孔將更為準確,且其他螺栓孔也省去了大量量測工作。個人認不為b. 在組裝上存在任何難點。
اللهم صل على محمد وعلى آل محمد كما صليت على إبراهيم وعلى آل إبراهيم في العالمين إنك حميد مجيد اللهم بارك على محمد وعلى آل محمد كما باركت على إبراهيم وعلى آل إبراهيم في العالمين إنك حميد مجيد.
Wow this guys father was good, an Irish guy slipped right in to a pakastanian..
Magnífico trabalho desses caras
Simplesmente sensacional!
this shop needs a BIG press
At 20:15 the men moving the rectangle blocks of metal,they must weigh 125 pounds each ,they have their safety shoes on.
The team of designers of the chief engineer who designed this gearbox is not qualified and failed:
1. Observe the overall structure of the gearbox and the construction conditions; With its existing construction tools, there is no reason to divide the work piece into three parts, and two joint surfaces are used; A reasonable partition only requires two parts and uses a single bonding surface.
2. Appropriate bonding surfaces, which can be: a. The common plane that exists in the extension line of the three gear shafts. b. The plane perpendicular to the center of the gear shaft extension line.
3. If there are no other special needs, my personally thinks that b. It is more reasonable, as long as there is no error in the measurement, the bearings at both ends of the three shafts, combined with the simultaneous construction, the shaft hole will be more accurate, and other bolt holes also save a lot of measurement work. Personally, I don't think that b. there are any difficulties in assembly.
Great job! One question: I've seen no lubricant for the gears. Running dry?
Up until now, the biggest scraper on CZcams belonged to Fireball Tools. Also, check out that lazy ol' fart with the sunglasses, just sitting on his lawn chair. That's GOT to be the chief engineer.
For the sake of Allah, get some proper wrenches and maybe a pair of steel tip boots or something to cover your toes maybe I a pair of gloves too and I know how about some safety glasses you guys sure like living on the edge but you’re good at polluting that’s for sure
Most complicated way to make metallic paste
Do you mean swarf ? You are not a machinist are you..?
@@kenc3288 I am. But this gearbox will mostly make metal paste and do some power transmission on the side
Can anyone give an example of what they use these gearboxes for?
Another cool video! But seriously guys, build a press will ya????
Not the greatest safety record, but at least they use steel calipers 😂
Nossa q incrível. Parabéns pra vcs gostaria de saber pra q serve isso?
Manufaktur good job
At 21.00 the guy cutting in the background got a hot foot 😂
I have never seen a planer of that size before. I wonder how old it is.
I used to operate a hydraulic planer that size in my apprenticeship in the 1960’s. Also in an industrial gearbox plant in Australia.🇳🇿🇳🇿
Dobra? To obraz nędzy i rozpaczy.
I'd like to see it working in place.
Neat and clean
That's not how drop forging works fellas
Just what was that cluster-fxxk at the start? Wasn't annealing, wasn't hardening, wasn't straightening...any thoughts? Haven't they heard of heat/dried CO2 for inserting shafts? Dropping that heavy weight and hoping? What's that all about? Can't they buy 350WT grade steel? Entertaining to watch BUT seriously, what are the workplace safety stats? Do they even compile them?
They were just checking they still had gravity.
Talk about bad engineering.
Not good practice to bore frame for bearings with clean faces then final assembly adding thick gaskets. Gearbox won't last long. Interesting method of assembly of shafts and gears also bearings onto shafts.😢
i see about 400 osha violations
And people wonder why America has difficulty competing in the manufacturing sector.
OSHA had spoiled Americans.
If the safety Nazis moved in on this factory, no more production, no more employment, no more company. They would become uncompetitive and the end would be disastrous for the local economy. Don’t try to impose western standards on this scenario. 😡
They have less injury than OSH Countries. These people know how to keep safe.
@@paulkurilecz4209have they?
Belo trabalho. ❤
Belo trabalho ❤
It is wonder why there are no set pins btween gearbox frames, Are there any special alignment methods ?
they rely on the bearings? quite simple to use set pins
What machine has such a gear box?
Apa nama alat ini dan apa fungsinya..?
Everyone is talking about safety shoes but you people must use your brain little bit what is the temperature of workshop how you can wear steel toe shoes there?
Ask a man that when he has to lose a toe or something else.
@@patrickrooney5130 that's just a story
Jab aap log etna bada kam karrahe ho to kiya etna riks kinyo lete ho hedrolic pares masen banalo
1 input 3 output where are these going to be used if it's not a secret?
It is used to drive rolling mills
Die Arbeiten wie vor Hundert Jahren, ohne jegliche Sicherheit. Primitiv ohne Ende
Semua kerja dama pikiran akal dan tenaga
Các bạn làm kiểu gì mà gây ô nhiễm nghiêm trọng
That’s soo dangerous work
Alat apa itu?
Bueno no se qué pais es creo que alguien deberia darles. Alguna nocion al menos en seguridad . Por lo demas alguno debería aprender la genialidad del no tener lo que tenemos los demas
Абсолютно бесстрашные ребята к их станкам просто дойти по этим ценам уже подвиг и они на этих гроба такие вещи делают.
Are you kidding me why even by the paining I must be the company color I’ve seen everything now that’s a fabulous piece of machinery there fellas nice Hackett whack it
21:10только этот архиме знает всё
🙏🙏🙏👍👍👍🙏🙏🙏
Почему ютуб перевирает комментарий?
Её ведь всё равно изкривит.там сварка присутствует
Mein Gott, schlimmer wie im Mittelalter. Und in Germany macht man ein Theater wegen Feinstaub.😱😱😱😱😱👎👎👎 Viele Grüsse aus Germany
Set of idiots are on the job having so big work shop, they should have incorporated one hydraulic press to meet their range. Job could have been still easier & neat.
Maquinaron las cajas de balero sin los empaques. Van a quedar ovalados.
and loose
Work without safety 😢
Need a new dress designer.wtf..
Me encanta ver como mantienen las normas de seguridad limpieza y orden
Сука, ну нагрей ты этот подшипник, его их мучать🥺
🥵
These guys are a joke. Half ass all the way.
Se
shit jab
Про уборку рабочего места не слышали???
Зачем? Завтра опять будет то же самое.
@@vitali623 да там неделями не убирают, если не больше.
For the sake of Allah, get some proper wrenches and maybe a pair of steel tip boots or something to cover your toes maybe I a pair of gloves too and I know how about some safety glasses you guys sure like living on the edge but you’re good at polluting that’s for sure