Constant Current Regulated Power Supply Module For Making Gans
Vložit
- čas přidán 21. 08. 2024
- This is a video on how to use the ZK-4KX constant current regulated power supply module to make Magrav GANs. The following link is an excerpt from the 86th KSW on how to mass produce the Magrav GANs the way it is done at the factory:
• 86th KSW GANS mass pro...
Model Number: ZK-4KX:
ZK-4KX CNC DC DC Buck Boost Converter CC CV 0.5-30V 4A Power Module Adjustable Regulated Power Supply
Amazon link:
www.amazon.com...
eBay link:
www.ebay.com/s...
Wiring diagram and panel cutout template pdf files
tinyurl.com/2p...
Electronic Enclosure Box Project Box with Fixed Ear Black 4.5 x 3.5 x 2.2 inch
tinyurl.com/4x...
Banana Jack Red
tinyurl.com/36...
Banana Jack, Black
tinyurl.com/ys...
10pcs DC Power Jack Panel Mount Connector 3-Pin 5.5 x 2.1mm
tinyurl.com/yw...
The alligator leads were made with a 3 ft length of red and black 20 gauge zip cord plus a pair of 1.75 in insulated alligator clips:
20 AWG Red/Black Auto Zip Cord
tinyurl.com/4p...
Large Insulated Alligator Clips, 1-Red/1-Black
tinyurl.com/3u...
Red Banana Plug, Plastic Shell
tinyurl.com/2p...
Black Banana Plug, Plastic Shell
tinyurl.com/39...
Thank you so much for your reply Yes I spelt it wrong , Interesting and nice to learn something new every day , keep up the good work
You're welcome.😊👍
Thanks for making this video, how did you set it to constant current?
You have to set the voltage higher than what it needs for the desired output current. That will automatically kick it into Constant Current mode because it forces the unit to limit the voltage to stay within the current setting. In the video right around the 3:05 minute mark, it's running at about .95 volts. As soon as I press the U/I (user interface) button you can see that the voltage was set for 12 volts. After I set the current to .500 amps and press the U/I button again it goes back into normal operating mode. You can see for a frame or two the output voltage increases from .95 to 1.0 volts which is way under the 12 volts setting. I hope this helps.
What is magrev gans , never heard of it and nothing on Google
Try searching magrav gans. I get a whole page of links. I hope this helps
These ZK units have one huge flaw. If you toggle it on and off with a CC limit set when you turn it back on the CC limit goes out the window if it’s anything over a couple hundred mA at most. Dangerous if using to charge Lithium Ion.
Disconnecting power entirely from the unit resets this so you just have to add a switch or something on the power in.
Thanks for the comment. I noticed something similar. I've been unplugging the power to end a batch, then plugging it back in to start another batch. I noticed sometimes the CC red LED wasn't lighting up, so I repeated unplugging it and plugging it back in until the CC red LED lit up. I was a little disconcerting.
@ericklein5097 In my situation I think it was popping out of CC mode because the output voltage was too low. The output range of the units I bought is 0.5 to 30v (although I've seen it get as low as 0.47v and the CC mode would still hold). I use 1 gallon containers and just by luck they usually start out right around 0.5v and as the job progresses the voltage gradually increases. Today it was popping out of CC mode because I forgot to top off each container with salted water. As soon as I did the voltage increased just enough to keep it going in CC mode.
Is this a dc-dc booster step up/down or does it have to have ac input only.
It's a DC-DC step up/down module. It needs a DC supply.
Awesome thanks
Please, what is the value of the capacitor connected to pin 1-2 of the illuminator ic lm358?
Sorry I don't have that information.
what are you making and what does it do
I'm making GANs (GAs to Nano of Solid matter). It is to be used as a coating for a plasma energy device.
oh word so pseudoscience, I feel you@@plasmaworkshop