CAMO DECK FASTENING SYSTEM!
Vložit
- čas přidán 7. 09. 2024
- #camo #decks #cedar Today we build a cedar deck using the Camo Deck system. This system uses a fastener device that helps hide the deck board screws.
Disregard: #decks #cedar #camo #system #hiddenfastener #carpentry #warren3 #customdeck
~-~~-~~~-~~-~
Please watch: "30 x 40 ATTACHED GARAGE BUILD! PART 2 #Carpentry #construction #remodeling "
• 30 x 40 ATTACHED GARAG...
~-~~-~~~-~~-~
Nice work man. I was going to get the KREGS DECK JIG until I saw this one that you use. Thanks for the video. Nice workmanship too homie. 🇺🇸🤙🏽
Thanks they work great!
Cedar looks good--for about 3 months and then it’s a disaster.just ripped up my own Cedar mistake that was bug eaten and rotted .In the future trying to pressure wash it they will end up beating the hell out of it since it’s so soft-That homeowners gonna regret using that stuff.you guys did a beautiful job building it though....
We suggest using a sealer like penofin to help for long-term life of the deck. Homeowners were going to seal there own deck on this job.
Good!!
Question why use bolts going into the post to support the load of the deck, why not notch out the post and rest the 2x10 on it.
That would offset the hand rail then. At leist for how I built it.
There is definitely more than one way to build decks! Also building inspector wants it that way.
@@Warren3carpentry notching a 4x4 will weaken the post too much to be a suffecient railing post
DCA 6 prescribes minimum 6 X 6 post and allows notching, the post to beam connection to the 4 X 4 in the video not so much. You also might want your crew to not install any joist hangars upside down.
The work looks very nice, where is this build located?....Is there a foundation under that slab?
We are located in South Dakota!
Curious on why you disn't use some sort of metal post base to keep the post off of the comcrete...They will start to rot in a few months
Yes i wish I had done that! Thanks!
What did you do with the board closest to the wall, you can only fit the drill on one side. An on the outer edge board, won't the outside screw hole be visible? What do you do when the outer board has a lip going outside the frame?
This deck job did have some face screws in those areas. However majority of the screws were used in the Camo fastener system. There are some other clips n such u can purchase also. For against walls and such.
@@Warren3carpentry thank you for the reply :)
Nice work!. Which is the rough cost for that job?
Thanks! I actually built 2 decks for this customer. I would have to check what pricing was per sq ft.
Great Vid! Sorry for dumb question.... What kind of wood are you using on the deck?
This is a cedar deck. Some of the hidden framing is pressure treated to save money for the customer. It turned out amazing!
Would you say the Camo Jig system is better than the Kreg jig for building a Composite deck not using fasteners? I was going to go with the Kreg jig but after seeing the Camo seem like less steps and looks good too?
I would say camo is better. No pre drilling
@@Warren3carpentry Screws are cheaper using the Kreg System though. Depending on the size deck you build can get expensive.
@@Warren3carpentry Actually I think the Camo might be Cheaper and looks easier. Thank you.
Greetings, what would you suggest for camo jig using composite treads?
I would use the short length stainless steel screws that camo has. Very small and hard to see!
Thanks very much. 👍🏼
Any issues using Camo screws on grooved Trex? I'm concerned it might pull the top lip down and maybe crack it...
I have yet to use it on trex!
@@Warren3carpentry I have, on non grooved. It worked great...but I'm building another deck and got a great deal on Trex ($2.50 per foot) but it's grooved. I'm going to give it a go.
Never screw joist in thru the face of the band. It looks unprofessional! Instead, toe screw them from joist side.
Thanks for the info! I will have to try that on the next home!
People who build without tool bags are a disgrace...
That person is my son, who just came by to help me. He has graduated with a degree in business management. And is a property manager in the biggest city in our state. So ya he is doing better than me... the one wearing the tool bags!
Stupid, distracting music.
Only been making videos for about 1 yr now, still learning. Thanks for the input!
I kinda liked the music! What is it?
@@MattGarofolo I get all my music on CZcams audio!
Do you happen to remember the artist? I don't know much about electronic music and hesitate to just jump in....there is just soo much of it. I do enjoy funky tracks....
@@MattGarofolo not sure there are so many songs in my Playlist I would have to go through them and listen to them till I found it. I would suggest going to CZcams audio and checking there music out.