How To Replace Passenger Side Axle Seal On A 2004-2008 Acura TSX
Vložit
- čas přidán 27. 10. 2018
- Brian Eslick from How to Automotive www.howtoautomotive.com takes you step-by-step through the process of replacing the passenger side axle seal on a 2004-2008 Acura TSX with 2.4L engine.
Affiliate link mentioned in the video for FEBEST 95HBY-35580811R Axle Case Oil Seal amzn.to/2D8Wpvp
Affiliate link mentioned in the video for OTC (7394 Universal Hub Puller amzn.to/2PZM0Fb
Affiliate link mentioned in the video for M18 FUEL 18-Volt Lithium-Ion Mid Torque Brushless Cordless 1/2 in. Impact Wrench W/Friction Ring Kit amzn.to/2D9Stum
Get your How to Automotive T-shirts, stickers, and more here: teespring.com/stores/how-to-a...
Affiliate link mentioned in the video for How to Automotive Tool Store www.amazon.com/shop/howtoauto...
Website
For more videos, tips, and to purchase recommended tools and products visit my website at: www.howtoautomotive.com/
Stay connected at:
Email: howtoautomotive@gmail.com
Facebook: / how-to-autom. .
Google+: plus.google.com/+HowtoAutomot...
LinkedIn: / brian-esl. .
Disclaimer
Owing to factors beyond the control of How to Automotive/Brian Eslick, it cannot guarantee against unauthorized modification of this information, or improper use of this information. How to Automotive/Brian Eslick assumes no liability for property damage or injury incurred as a result of any information contained in this video. How to Automotive/Brian Eslick recommends safe practice when working with power tools, automotive lifts, lifting tools, jacks and jack stands, electrical equipment, blunt instruments, chemical lubricants, or any other tools or equipment seen or implied in this video. Because of factors beyond the control of How to Automotive/Brian Eslick, no information contained in this video shall express or imply warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not How to Automotive/Brian Eslick. #howtoautomotive #AcuraTSX - Auta a dopravní prostředky
For those of you that have asked how they can tip me. You can now click the “super thanks” button and add a tip. Grateful for all my viewers and subscribers! This channel would be nothing without you!
Very professional, very detailed...he makes it look like a walk in the park.
Thank you!
Just completed this job on my son's 2003 Accord. No more leak! Thanks for your help!
Thanks! The old gasket used as a tool to pound in the new gasket saved me! Thx
Very helpful vid. What would be the best method for removing/installing the intermediate shaft and axel end set/snap ring? I'm installing the axels on my car and would like to install the new set rings correctly. Thank you
When I did mine I hit the seal till it was flush but my dust cap on the intermediate shaft is bent, would this cause any leakage I wouldn’t think so since the seal is what holds fluid in but then again the cap puts pressure on seal
The exact problem I have with my 2013 cr-v. Thank you so much!
Mike T it’s not to bad of a repair . You got this. Thank you for watching!
Thank you for the video. I learned something new today.
Thx for sharing. Direct to the point instructions. Keep up the good work.
Thank you for watching!
Would that leak transmission fluid and engine oil?
Great video, thank you!!
Do you know if it would be the same with a 2007 Ridgeline... for the passenger side and with an intermediate shaft? I need to replace the seal only on the passenger side and it sure would be nice it it was as easy as the TSX!
One of my half shaft bolts got stripped but I got the other 2 on there right and tight no issues while driving you think I’ll be okay ?
Great video thanks for the tips
I've got this problem on my 2013 RDX J series engine. Driver side. Leaking small amounts of transmission fluid. My mechanic is recommending I replace both the seal and axle. What are your thoughts? Would you replace just the seal or both while you're at it? I'm at 105K. OEM Acura axle is not cheap 😭
What if it makes a noise almost like there's a knot in my tire when I slow down or turn a certain way, would make that noise if the seal is broken?
Why am I having trouble sliding half shaft back in? Does it only goes in one way?
Great instruction! I noticed you got a cracked bushing in the lower control arm, where the strut fork is mounted on.
Did you have to drain the transmission fluid ?
Would this process be the same as the drivers side?
Is this a manual transmission or automatic? Is the seal the same for both?
Very nice video, Thank you!
Thank you. Did everything go smooth for you?
Thanks for the video! Acura wanted near $700 for this...
Question, I know you cleaned where the seal goes, and then lubed up the inside before sliding the axle. How come you don't lube the seal with ATF before putting the seal itself in?
What's the part number on the CV axle
Would this cause a vibration in the car if bad?
do you need to drain the transmission fluid first?
No you don’t need to.
Nice one .
125 SM thank you!
So there was no need to remove the strut fork, tie rod, sway link?
Hi where did you get the puller you used for removing the driveshaft? Thanks
Ben Pattison I got it off a Tools truck. There is an affiliate link for it in the description ⤵️
So wait, how far do you put the seal in? Until it stops? I tried to replace mines and now it’s leaking. I feel like I didn’t put it all the way in.
Jordan Kim did you ever receive a response on this? I’m about to do mine
Same with me I don’t know what I did wrong
Does replacing the axle seal, the same for makes and models
mckoy lach This Seal is pretty much the same on Acarus in Honda’s .
Could someone tell me if this is A COMMON transmission fluid LEAK on the TSX ???
I went under my son's 2006 TSX yesterday and all the engine is very clean, no leaks at all, except for that SAME SPOT where the Axle joints the Gear Box. Thanks in advance 😎🤝🏻🙂👍🏻 Nice Video
I’m 2 years late but this happened to mines because I’m low to the ground so my axle is bending the seal out. It depends on how well you treat the car and especially if you use “m” the tsx in some way goes into sport giving it more and if you go from 1-2 fast your axle is going to pop out from the torque since tsx are untuned from factory not making all its power and reliability
Same for Honda accord 2004-07?
Thank you
mckoy lach thank you for watching!
So the seal doesnt bottom out when installing it?
nice
SVANG VICHITH original video thank you!
would these same steps work on a 06 acura tl?
Yup same set up
What should be the cost of this job?
it's the same for acura tl 04?
Why torque the tire lugs to 79? I through spec was 80?
In the manual it's 79. something... He rounded down, I round up. Doesn't matter. 1ft lb isn't going to make a difference.
Why am I having hard time sliding back in? It only goes back in half way
Did you check if the new and old axle are the exact same type and size? Compare the splines, the number and width of the spline teeth especially. Same size clip ring?
How much would it normally cost to do it at the automotive repair shop?
10 - 20$ for the seal and about 60 for Labour
$330 in my city, which is way out to lunch.
$100 for labor in Michigan
@@Taronenko1 same in boston
What a frickin awesome video. You just gave me the confidence to do it myself..
Nice. Good luck with it. Thank you for watching!
@@HowtoAutomotive thank you.
Doing axle seal ..... do I need to drank the transmission fluid first?
No. Only drain it if it needs servicing.
in left and right side of my axle inner cv joints have little oil ,,,,,it mean both side of axle are leaking transmission oil right? left and right side it should be dry all the time am i right??
Andywensheng cao where it go’s in the Transmission yes it should be dry.
How to Automotive thank you now I know what to do ........
No, don't drink transmission fluid.
I did change my using your this video it is really easy but now the seal is leaking transmission oil i need to do the job again maybe the seal was defective
It possible it’s the wrong seal
How to Automotive thanks for the reply i remove the seal again yesterday and tiny spring in the seal was not in place i purchased that seal in oreilly auto parts i will purchase another today and install it seem how it goes
The muffler is on the way did you remove any other part am doing that on my Acura TL but there’s other parts blocking bolts
I didn’t but if it’s a different year things may be slightly different.
👍👍👍
Saved me 1,000 dollars
Nice love hearing that! Thank you for watching!
I forgot to tell you i have a 2006 tl. Is the the same procedure?
Good vid... However, the torque for the lower ball joint is 65 ft lbs not 30
👍🏿👍🏿👍🏿 thx
Can you drive the seal on too far?
Yes you can’t possibly driving too far.
@@HowtoAutomotivewait, your answer is contradicting itself.
Yes
Older models2002
links for parts and tools are in the description