RC4wd C2X, Suspension Mods & Test Drive
Vložit
- čas přidán 26. 04. 2020
- Messing with the C2x from rc4wd, lengthening the wheelbase a little
If interested in supporting the channel, here is my patreon:
www.patreon.com/RCeveryday?fa...
Check out my Amazon influencer store page for some of these products;
amzn.to/2NMKTtX - Auta a dopravní prostředky
While I'm going a slightly different route with mine, you might want to check out the series I've done for some performance improvements to help the C2X! Great video!
Yeah I definitely need to watch that again I've had nothing but trouble with my c2x
You could dig a course in the back yard. That’s what I did. lol. Now our parks are still open so we’re pretty lucky. 👍🐒🇺🇸
Nice truck!
I know this truck is a little different than the TF2 lwb, but it should be close. It looks like they might have mounted the body a little higher. I used the body lift for the TF2 lwb and it created a space between the body and sliders. I flipped the sliders upside-down and that brought them up to the body (I had to remove the innermost bar to clear the body mount). Good call on extending the links, looks better! I hope this helps!😊
Good info 👍
Lead stick on weights are hard to get balanced. I've been using Beef Tubes Beef Patties. They replace the hubs, and also are 4mm off set. One ounce per wheel, all the weight ya need down low. Keep up the mad science my friend!!
Monita esa toyota me encantan las modificaciones tanto interior como estética de carrocerías modificadas.😍👍
Add weight between the Wheel and Tire you can buy weights that sticks to the wheel that goes up under the tire, that will give you your bottom weight
Lead bbs in the tires bird shot will work too
wonder if you can fit a leaf suspension with yota axles... it would give some weight to the bottom. I might have to test that...
you could get some beef patties wheel weights. you could also get wheel weights that go inside the wheels...hope this helps.
I see you are doing a bit of weeding, RC style.
cool
Could you put longer shocks on the c2x? Always looks like it needs to be higher compared to a d90, with the longer wheelbase it seems to hit the rocks.
How much Weight are you thinking of adding?
Truck looks brilliant 👍👍👍
Not sure if it was a mistake or not but I put scx10 ii axles on mine. Now my front end needs different links. Wish I could figure out a 4 link setup. But I’m knee deep into it and can’t go back. Lol
watch your vids all the time and subed from long time.... work on that back yard trail area!
Man I did for a while. It floods every time it rains and washes it all away.
Lead Weight in the wheels.
Hi how are you doing see I have a semi truck i run a model car garage and in turn them into rc I need a lil help with this semi truck I wanna replace the motor infant know how
Have you ever put a tf2 body on a scx 10 2 I have a set of mts that were 3 d printed to fit the original mounting holes on the tf2 body but the rear shock mts hit the bottom of bed and will not let holes match up any help you can give is greatly appreciated. You have some many awesome builds. Such attention to detail very talented
I did that once with an scx10 one, not much you can do about it, I just cut holes in the bed fo the shocks to stick through. Dinky RC use to make a anticancer system that relocated the shock so you didnt have to cut the floor, havent seen them in a while though.
What about the lead wheel wieghts? Ive seen ppl sticking them on the inside of the wheel adds low weight and its outta sight been thinking about trying it myself
lol been doing that since 2008… where you been?
@@RingLeaderElon man I had just got into crawlers I was into the basher seeing back then I’ve already started using them and stopped already. Lol.
Bird shot in the tires. They will always find the lowest cg.
Will the rc4wd K44 metal axles fit here? They’re the same width as the d44 plastic axles I believe.
They might. Not sure if the 4 link mount width is the same. The k44 are the same width as the standard yota axles.
@@RCeveryday I emailed rc4wd and their response was "This would work,
you may have to use some different length links in some areas." I'm still hesitant to buy as I am not yet 100% sure what other items to purchases or what modifications to use. Upon checking they are the same width and I think with the panhard and rear bracket it will fit. But I'm a little tight on budget and this is too risky for me at this point.
So did you make 4 2.5mm spacers? To place on each rod end? I just received my c2x in the mail.
I think they were 2.5mm. I have a bunch of spacers from yeah racing (I think). I buy the bulk packs of them.
Thanks man. Will look out for those. I like the bed you fabricated BTW.
Ok I'm slow how do I move the front axle forward my steering locks up every time I turn my crawler had this issue since day one all it's done is collect dust because of the fear of burning up the servo
I just added spacers to the front suspension rods. Maybe about 5 mm
@@RCeveryday thank you I'm not going to lie I just thought that sounded like it was too easy and I missed a step 🤣
Wheel weights
Where did you get the bed for it?
I just made the bed from an old body I had. There is a video of it somewhere in the playlist.
@@RCeveryday I wanted to see if I could mount the 2 door Mojave body on it. Those pumpkins were way to big. Changing the axles brought on more problems than anticipated.
Needs paint!
First