i used orings. 23.2x 2.5mm the pins are a bit of a fiddle to get back in but they work. tried 150 psi gas and propain and they are still good. ive got the a1a 45rnd mags. so far so good
Do you have any proble with the bolt locking system of those mags ??? I have 4 new ones (EVO V2) and in all 4 the bolt locking lever doesn t seem to work properly ??????? Thx !
I would suggest filling them then doing 5 or 10 dry fire shots to purge the magazine and fill again. As long as you dont completely empty the magazine you should only have to do it once
@ollegoop9 not really. I just stripped it down, as per this video, cleaned and greased the base, put a squirt of silicon oil into the fill valve, made sure it was tight and that seemed to work
Hey I just got 2 of these mags today, my first 2 gbb mags to go with my new DE N4 rifle i just got. When i filled both mags, one mag is hissing gas from the top ribber square thing. I keep weighting iot and it is holding at 356/7g and my other one is 355g full, Is the hissing due to overfill? what could be doing it.
We are just starting to get the Gelblaster version of GBBR’s in Australia and I am finding your videos great keep up the great work
i used orings. 23.2x 2.5mm
the pins are a bit of a fiddle to get back in but they work. tried 150 psi gas and propain and they are still good.
ive got the a1a 45rnd mags. so far so good
Do you have any proble with the bolt locking system of those mags ??? I have 4 new ones (EVO V2) and in all 4 the bolt locking lever doesn t seem to work properly
???????
Thx !
what screwdriver u using mate looks sick
How do you apply the gasket sealer and what brand do you recommend
guns modify will make a version for VFC BCM GBBR ?
I have the same screwdriver, love it to death
what screwdriver is that
thx
How did you manage to get rid of the air bubbles in the GM pmags as the fill valve is next to where gas comes out as opposed to more traditional mags?
I would suggest filling them then doing 5 or 10 dry fire shots to purge the magazine and fill again. As long as you dont completely empty the magazine you should only have to do it once
@@Jaeger-Precision So fill, 10 shots, fill, 10 shots and thats the air bubble gone? no venting the gas via the pin?
@@Gisborne1990 should be yeah. Atmosphere is lighter than propane and will sit at the top of the magazine.
One of mine is leaking from the fill valve. Any suggestions on how to fix?
mine is aswell did u find a fix?
@ollegoop9 not really. I just stripped it down, as per this video, cleaned and greased the base, put a squirt of silicon oil into the fill valve, made sure it was tight and that seemed to work
:o
Hey I just got 2 of these mags today, my first 2 gbb mags to go with my new DE N4 rifle i just got. When i filled both mags, one mag is hissing gas from the top ribber square thing. I keep weighting iot and it is holding at 356/7g and my other one is 355g full, Is the hissing due to overfill? what could be doing it.
How do you rate them compared to the original magazines?
I highly rate them
@@Jaeger-Precision I definitely trust your opinion so it looks like I’ll be ordering some then thanks mate
@@scottelliott2843 if in uk. airsoft direct have them instock
I bought mine from wgc. UK shops sell them at ridiculous prices compared.
@@Jaeger-Precision you’re right about the UK prices when you ordered from there is so much of an additional cost when they delivered
Why the fuck is this so over engineered