GIMBAL BEARING REPLACEMENT - How to Replace the Gimbal Bearing on an Alpha Drive
Vložit
- čas přidán 29. 08. 2021
- In this video we’ll show you how to replace the Gimbal bearing on an Alpha drive. Gimbal bearing replacement can be done in a couple of hours. Do it yourself and save money!
Get FREE unlimited Shipping, Movies and more - amzn.to/3jbgbsH
Click on the Links Below to Purchase:
*Sierra Gimbal Bearing 18-2100 - amzn.to/3yrvL9n
*Quick Silver Gimbal Bearing Generation 2 Drives - amzn.to/3yBhC9E
*Gimbal Bearing Removal/Puller/Alignment/Installation Tool - amzn.to/3DvFCih
*Alpha Drive Gasket Set - amzn.to/3kBwi3B
*Quick Silver Bellows Adhesive - amzn.to/3BosMjZ
*Marine Grease - amzn.to/2QP6dQp
*Grease Gun - amzn.to/3zudlGw
*Sledge Hammer - amzn.to/2WBMwRW
*Craftsman Tool Set - amzn.to/2D9Qhoo
*Craftsman 1/2 inch Drive Ratchet - amzn.to/3k2JqNs
*Craftsman 1/2 inch Drive Extensions - amzn.to/32zT436
*Craftsman 1/2 inch Drive Socket Set - amzn.to/38nHU4C
*Craftsman Torque Wrench 1/2 inch Drive - amzn.to/3cwcTwL
*Craftsman 1/2 inch Impact Wrench - amzn.to/2YeshL7
*DeWalt 1/2 inch Impact Wrench - amzn.to/3kGGt79
*DeWalt Cordless Drill - amzn.to/3zwtIlU
*Wire Wheel - amzn.to/3BrFG0w
*Scraper - amzn.to/38p1KfI
*Pry Bar Set - amzn.to/3t0fNC6
*Nitrile Disposable Gloves - amzn.to/2RO0kqi
*Gojo Hand Cleaner - amzn.to/2HgIuXF
*Shop Towels - amzn.to/2ZQvnTs
*Fixin To T-shirt - amzn.to/33OgqTg
*Scallywag Pirate Hoodie - amzn.to/2P7L2vt
* Fixin It is an Amazon Associate and earns from Qualifying Purchases.
email: fixinit7@gmail.com
Instagram: / fixin_it_
TikTok: vm.tiktok.com/wmnw6v/
#fixinit #boating #gimbalbearing #howto #diy #bearing #formula #repair
Disclaimer:
Due to factors beyond the control of Fixin It, I cannot guarantee against improper use or unauthorized modifications of this information. Fixin It assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Fixin It recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Fixin It, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Fixin It. - Jak na to + styl
Thanks for the video, its awesome to see you ain't letting no bionic leg slow you down! Let me sling that drive like a paper weight! NICE!
I knocked my gimble bearing out with a brass drift and one smack of a hammer. The last guy didn't even get it all the way installed! GEEZ. It was 10mm from the seat!
Thanks for putting this video together! I almost killed my new bearing not seeing the grease hole! Lifesaver Bro
Thanks for watching!😎
I didn't see how you got the seal out. Gotta be an easy way to do it.
He used the same puller he used for the bearing
What did u use to hold the gasket
you don't need any sealer for the gimble gasket, just the O ring
YOU CAN NOT BEAT ON THAT PART OF THE BEARING. YOU JUST RUINED IT!!!!!
My bearing retainer keeps popping out halfway around.
He didn't grease the U joint while he had it out.
He did. Just didn’t film it.
I’m a certified tech, I’ve seen wrong doings and wrong tools…. Buy the correct tools and stop showing people the wrong way… your gimble seal came out probably because you used a slide hammer…
How not to change a gimble bearing 101.
Destroyed the new bearing by beating it in by the inner race which puts pits in the the inner and outer races causing pre-mature failure then didn't torque anything properly and at the end hits the threads on the trim cylinder shaft with a hammer and wonders why the threads were damaged in the first part of the video. Also why didn't they figure out the cause of the water leak and repair that plus new u-joints from sitting in the water. Should never use a wire wheel to remove gasket material as you can damage the soft substrate and every zirc needed to be greased along the way as well. How not to service an out drive. Poor maintenance is inexcusable, just look at the condition of the boat and out drives, I'd move on to a video from more experienced competent instructors!